Manual de instrucciones de Pro-Ject Audio Systems RPM 6.1 SB

Resumen del contenido incluido en la página 1

INSTRUCTIONS FOR USE
Pro-Ject RPM 6.1 SB

Resumen del contenido incluido en la página 2

13 16 6 1 6a 22 3 15 17 2 4 7 7 1 8 18 5 9 21 20 33 45/78 SPEED Speed 33 45/78 Speed Box SPEED BOX 23 23 23 33 45/78 SPEED Speed 33 45/78 Speed Box SPEED BOX 24 38mm 17 21 37mm 9a 3a 25 © Audio Trade GmbH · Pro-Ject RPM 6.1 SB · Revision 20.2.06/1.5.06 2 14

Resumen del contenido incluido en la página 3

PRO-JECT RPM 6.1 SB Controls, features and connections 1 Motor transportation screw (marked red) 2 Stepped drive pulley 3 Drive belt * 3a Hook 4 Hub * 5 Sandwich platter * 6 Tonearm counterweight * 6a Downforce scale 7 Tonearm lift lever 8/18 Tonearm rest and removable transport lock 9 Tonearm tube 9a Tonearm base 13 Power supply socket 14 Phono output sockets and earth connection 15 Anti-skating weight adjustment scale 16 Anti-skating weight * 17 An

Resumen del contenido incluido en la página 4

Set-up Screw the two feet (23) onto the threaded bolts located on the underside of the plinth. Make sure the surface you wish to use the turntable on is level (use a spirit level) before placing the turntable on it. Carefully insert the spindle of the hub (4) into the bearing. Fit the drive belt (3) around the hub (4) and the smaller diameter part of the motor pulley (2). Avoid getting sweat or grease on the belt as these will deteriorate the performance and reduce the belt's lifespan. Use

Resumen del contenido incluido en la página 5

Adjusting the vertical tracking angle (vta) Put a record and the record weight on the platter. When the needle is lowered into the record groove and the tonearm is not resting on the lift arm, the tube of the tonearm should be parallel to the surface of the record. If it is not loosen both allen screws in the tonearm base just enough to allow vertical movement of the arm pillar without force and slide the arm up or down until it is parallel. Carefully retighten the allen screws without ap

Resumen del contenido incluido en la página 6

Mains power connection The turntable is supplied with a power supply suitable for your country's mains supply. Check the label before connecting to ensure compliance with the mains rating in your house. Connect the low voltage plug from the power supply to the socket (13) on the rear of the record player before connecting the power supply to the mains. Switching on and off Pressing the power switch (20) alternately starts or stops the motor. Changing replay speed 33 45/78 SPEED Speed 33

Resumen del contenido incluido en la página 7

Potential incorrect use and fault conditions PRO-JECT turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances. Therefore the following list of common fault symptoms is included. The platter doesn't turn although the unit is switched on: The unit is not connected to the m

Resumen del contenido incluido en la página 8

Counterweight Hub Power supply Accessories 2 motor transport screws (marked red) Tonearm transport lock Please remove feet bevore repacking Platter Record weight © Audio Trade GmbH · Pro-Ject RPM 6.1 SB · Revision 20.2.06/1.5.06 8 !

Resumen del contenido incluido en la página 9

Produktübersicht Phono pre-amplifier Phono Box II Amplification and RIAA equalisation for MM and MC cartridges Dual-Mono circuitry for improved channel separation Available in silver or black finish Phono pre-amplifier Phono Box SE Amplification and RIAA equalisation for MM and MC cartridges Selectable impedance for MC cartridges Subsonic filter Dual-Mono circuitry for improved channel separation Tube phono pre-amplifier Tube Box II Amplification and RIAA equalisation f