Resumen del contenido incluido en la página 1
CCA5/7 Extractors
Manual for Installation, Use and Maintenance
Passionate about style
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
Resumen del contenido incluido en la página 2
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment. This appliance is not designed to be used by people (including children) with reduced physical, sensorial or mental capacity, or who lack experience or knowledge about it,
Resumen del contenido incluido en la página 3
Using your Extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for approximately 15 minutes after the end of cooking. A - Light switch B - Power indicator light C - Power switch A B C A1 A2 C1 C3 C2 C4 Fig. 1 To switch the extractor light on or off • Slide the light switch to position A1 for off, or A2 for on. To switch on the extractor, or change the motor speed • Slide the power switch to the position required dependent
Resumen del contenido incluido en la página 4
Care and Maintenance IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. Cleaning You should use a non-abrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. You can clean you extractor effectively by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth, for example the CDA E-Cloth. Cleaning the grease filter
Resumen del contenido incluido en la página 5
Changing the Light IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. DO NOT CHANGE THE LIGHT BULB IMMEDIATELY AFTER USE AS THE BULB WILL BE HOT. ALLOW IT TO COOL BEFORE REMOVING IT. 1. Unfasten the sliding brackets on either side of the cover panel and the cover panel will hinge open. 2. Remove the faulty light bulb and replace with a light bulb no more powerful than that specified on the rating plate. 3.
Resumen del contenido incluido en la página 6
Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSED SPUR OUTLET AND PROTECTED BY A 3A FUSE. We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations. DOUBLE POLE SWITCHED The wires in the mains lead of this appliance are coloured in accordance with the FUSED SPUR OUTLET following
Resumen del contenido incluido en la página 7
Electrical Information Mains electrical voltage: 230 – 240Vac. Total rated power consumption CCA5: 150W. Total rated power consumption CCA7: 300W. Troubleshooting Please note: Your extractor is equipped with a motor protection device that will switch off the motor to prevent damage from overheating. This may happen during cooking when most or all of the zones/burners are being used simultaneously. This is normal, and the extractor will work again once the motor has cooled sufficiently. If yo
Resumen del contenido incluido en la página 8
Installation When the extractor is to be installed above an electric hob, the minimum distance between the hob and extractor must exceed 600mm (650mm is recommended). When the extractor is to be installed above a gas hob, the minimum distance between the hob and extractor must exceed 700mm (750mm is recommended). If the instructions provided with your gas hob state that the required distance between the hob and extractor must be greater than 700mm, then that is the distance that should be obs
Resumen del contenido incluido en la página 9
257 284 Mounting your Extractor The extractor can be mounted in one of two ways: 1. Mark out the dimensions of the cut-out based on your hood; the dimensions required are as follows: - Version Cut-out Width Cut-out Depth CCA5 495 257 CCA7 695 257 2. Hold the extractor in the housing and secure to the canopy using 4 wood screws, located in the corner of the extractor, as shown as C in figure 3. We recommend that you seek the help of another individual when carrying out this task.
Resumen del contenido incluido en la página 10
Resumen del contenido incluido en la página 11
Resumen del contenido incluido en la página 12
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
