Resumen del contenido incluido en la página 1
PT2275SW / PT2285PW
Touch Screen LCD Monitor
USER’S GUIDE
www.planartouch.com
Resumen del contenido incluido en la página 2
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced,translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission. Windows is a registered trademark of Microsoft, Inc. Other brand or product names
Resumen del contenido incluido en la página 3
Table of Contents Usage Notice Precautions............................................................................................................................. 1 Introduction About PT2275SW / PT2285PW ............................................................................................. 2 Touch Screen for PT2275SW ....................................................................................... 2 Touch Screen for PT2285PW ................................................
Resumen del contenido incluido en la página 4
Usage Notice ! Warning - To prevent the risk of fi re or shock hazards, do not expose this product to rain or moisture. ! Warning - Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Do: • Turn off the product before cleaning. •
Resumen del contenido incluido en la página 5
Introduction About PT2275SW / PT2285PW The PT2275SW / PT2285PW is a 22" fl at panel screen with an active matrix, thin-fi lm transistor (TFT) liquid crystal display (LCD). Features include: • Direct Analog signal input • Direct Digital signal input • Active matrix TFT LCD technology • 1920 x 1080 resolution • 22" viewable display area - 16:9 aspect ratio • 31.47 ~ 82.3 KHz horizontal scan • 56 ~ 75 Hz high refresh rate • 0.24825mm x 0.24825mm pixel pitch • Auto adjustment function • Mu
Resumen del contenido incluido en la página 6
Touch Screen for PT2285PW • Project Capacitive touch screen for fi nger input only • Surface: Glare treatment • Interface: USB controller • Transmittance: 90%±5% ® • Driver: Windows 7, VISTA 64/32 bits, XP, 2000, XP Embedded Express, Linux, ® Apple Mac OS. 3
Resumen del contenido incluido en la página 7
xxxxxxxxx / xxxxxxxxx xxxxxxxxx USER’S GUIDE www.planartouch.com Package Overview LCD Display VGA Signal Cable Power Cord USB Cable ( A to B) Audio-in Cable RS-232 Cable (PT2275SW only) Cable Cover Touch Screen Driver DVI-D Cable Installation CD-ROM User’s Guide Landing Strip Screw 4
Resumen del contenido incluido en la página 8
Installation Product Overview • Front View PT2275SW PT2285PW • PT2275SW Bottom View (Without Stand) AUDIO DVI IN AC IN VGA IN RS-232 USB • PT2285PW Bottom View (Without Stand) Audio DVI IN AC IN USB VGA IN 5
Resumen del contenido incluido en la página 9
Start Your Installation 1. Lay the LCD fl at on an even surface. 2. Remove the stand back cover by pulling in the direction of the arrow as seen in step 2 diagram. 3. Move the stand into position as seen in step 3 diagram. 4. Connect the cables to the appropriate connectors as seen in Step 4 diagram. Use step 4-1 or 4-2 diagram if using the RS-232 serial connector. Use step 4-3 diagram if using the USB connector. Step 2 Step 3 Step 4-1 Step 4-2 Audio Audio DVI VGA Power RS
Resumen del contenido incluido en la página 10
5. Take the optional cable cover and screw from the accessory box. Position all cables under the cover lip as seen in the step 5 diagram. 6. Using a Philips Head screwdriver, insert the screw (CPMSP M3x10) into the cable cover and monitor as seen in the step 6 diagram. 7. Re-attach the stand back cover to the LCD stand by pressing fi rmly until the tabs snap into place as seen in the step 7 diagram. You may also keep the cables in order by using the cable organizer. Step 5 S
Resumen del contenido incluido en la página 11
Connecting the Display (Figure 9.1) To setup this display, please refer to the following fi gure and procedures. 1. Be sure all equipment is turned off. 2. Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet (9.1). 3. Connect the D-SUB or DVI cable from the display's VGA or DVI input connector to the D-SUB or DVI connector of your host computer and tighten the screws (9.1). 4. Connect the Audio-In cable from the audio input p
Resumen del contenido incluido en la página 12
(Figure 9.1) PT2275SW PT2285PW 9
Resumen del contenido incluido en la página 13
Kensington Security Slot The monitor can be secured to your desk or any other fi xed object with Kensington lock security products. The Kensington lock is not included. 10
Resumen del contenido incluido en la página 14
VESA Mount Your Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which defi nes a physical mounting interface for fl at panel monitors, and corresponding with the standards of fl at panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your monitor. To mount the monitor on a UL certifi ed swing arm or other mounting fi xture, follow the instructions included with the mounting fi xture to
Resumen del contenido incluido en la página 15
Remove the Deskstand Remove 4 screws and then remove hinge. 12
Resumen del contenido incluido en la página 16
User Controls Side Panel Controls Icon key Name Menu Up Down Enter Power OSD Menu off status Menu on status Key Menu appear Menu disappear / return to main item Brightness Main item select up / Adjust up Mute Main item select down / Adjust down Enter / Select sub-item function Power On / Off 13
Resumen del contenido incluido en la página 17
How to Use the OSD Menus Icon Key Name Menu Up Down Enter Power 1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the six functions in the main menu. 2. Choose the adjustment items by pressing the “Enter ” button. 3. Adjust the value of the adjustment items by pressing the “Up” or “Down” button. 4. With the OSD menu on screen, press “ Menu” button to return main menu or exit OSD. 5. The OSD menu will automatically close, if you have l
Resumen del contenido incluido en la página 18
On-Screen Display Menus Main OSD Menu: ITEM CONTENT Contrast The monitor luminance level control. Brightness The monitor backlight level control. Auto Adjust Fine-tune the image to full screen automatically. Left/Right Moving screen image horizontal position to left or right. Up/Down Moving screen image vertical position to up or down. Horizontal size The screen image horizontal dot clock adjustment. Fine The screen image pixel phase adjustment. OSD Left/Right Moving OSD menu horizontal positio
Resumen del contenido incluido en la página 19
Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen. ► Check that all the I/O and power connectors are correctly and well connected as described in the “Installation” section. ► Make sure the pins of the connectors are not crooked or broken. Problem: Partial Ima
Resumen del contenido incluido en la página 20
Warning Signal If you see warning messages on your LCD screen, this means that the LCD display cannot receive a clean signal from the computer graphics card. Below are the three kinds of Warning Signal. Please check the cable connections or contact your local dealer or our service center for more information. No Signal This message means that the LCD display has been powered on but it cannot receive any signal from the computer graphics card. Check all the power switches, power cables, and V
