Resumen del contenido incluido en la página 1
WARNING! IF THE INFORMATION IN
THIS MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUSING
PROPERTY DAMAGE,PERSONAL
INJURY OR LOSS OF LIFE.
DIRECT VENT
FOR YOUR SAFETY
INSERT
MODEL
WHAT TO DO IF YOU SMELL GAS:
* Do not try to light any appliance.
* Do not touch any electric switch.
IRHEDV32
* Do not use any phone in your building.
* Immediately call your gas supplier
from your neighbours phone. Follow
the gas suppliers instructions.
* If you cannot reach your gas supplier
call th
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS Please read the Installation & Operating Instructions before using this appliance. Thank you and congratulations on your purchase of a Irving Oil fireplace. IMPORTANT - READ ALL INSTRUCTIONS AND WARNINGS CAREFULLY BEFORE STARTING INSTALLATION. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN A POSSIBLE FIRE HAZARD AND WILL VOID THE MANUFACTURERS' WARRANTY. Installation Instructions ...............................................................................................
Resumen del contenido incluido en la página 3
INSTALLATION INSTRUCTIONS This gas appliance should be installed by a qualified IMPORTANT: installer in accordance with local building codes and with PLEASE REVIEW THE FOLLOWING current CSA-B149.1 or .2 Installation codes for Gas Burning Appliances and Equipment. CAREFULLY FOR U.S.A Installations follow local codes and/or the current It is normal for fireplaces fabricated of steel to National Fuel Gas Code. ANSI Z223.1. give off some expansion and/or contraction noises during the start up or coo
Resumen del contenido incluido en la página 4
FIREPLACE & TRIM DIMENSIONS 3" (75mm) R - Fireplace opening width U Q - Fireplace opening height S - Depth of insert Q V T - Firebox width at insert depth(S) T U - Firebox depth at insert back height (V) S V - Insert back height 1= SS or SSD Trim R 2= SL or SLD Trim MINIMUM FIREPLACE 3= SXL Trim INSERT OPENING 4= BSL Trim 5= BXL Trim IRHEDV32 5/8" A1 26 676 mm 3/8" B1 38 975 mm A2 29" 737 mm T 15/16" B2 41 1065 mm R A3 33" 838 mm I B3 44" 1118 mm M A4 28" 712 mm 7/8" B4 40 1041 mm 1/2" A5 30 775
Resumen del contenido incluido en la página 5
GAS LINE INSTALLATIONGAS GAS SPECIFICATIONS MAX. MIN. INPUT INPUT When purging the gas line, the front MODEL FUEL GAS CONTROL B.T.U.H B.T.U.H. glass must be removed. RHEDV32RP Propane Gas Millivolt Hi/Lo 27,000 20,250 The gas pipeline can be brought into the fireplace base This appliance may be installed in an aftermaket from the right side. It is most convenient to install it permanently located, manufactured (mobile) home, from the right side into the valve. where not prohibited by local cod
Resumen del contenido incluido en la página 6
L I P TP TH TPTH ----- ----- HONEYWELL VALVE INSTALLATION OF TRIM SWITCH FOR RP GAS VALVES 1. Thread wire through openings on the right side of fireplace. Do not cut wire or insulation on metal edges. 2. Slide switch assembly from the back, between subframe and trim, then fasten the screw. (Fig. 3) 3. For left side installation reverse switch position in bracket and repeat Step 2 (Fig. 4 ). 4. Connect wiring to gas valve (Fig. 5a & b) and switch. Fig. 5b ADJUSTMENT OF LEVELLING BAR (IF REQUIRED)
Resumen del contenido incluido en la página 7
LINER INSTALLATION - Fig. 6 VENTING DIAGRAM The collar extending down from the termi- Flue gas exits nation base is the air intake connector. Be through the vent sure the flex vent, which is connected to termination rain cap 1) Attach flexible pipe to rain cap this collar, is also connected to the labelled 2) Secure with clamp 3) Attach raincap to vent air intake flue collar on the fireplace. Make termination using three screws sure the Flex vent is attached on the correct Outside combu
Resumen del contenido incluido en la página 8
3" FLEX VENT FAN KIT DAMPER TWO PIECES 115 volt, 60 Hz.56W CLAMPS & SCREW The fan kit includes the following: fan, temperature sensor, speed control and a 6 ft. cord. The following explains how FASTENER to start and set the fan for automatic operation. PLATE 1. Plug in the electrical cord. 2. Start gas fire - see lighting procedures. GASKET 3. Turn on fan speed control. FLUE COLLAR 4. Wait until the unit has warmed up sufficiently to PLATE activate the termperature sensor, approximately 5-
Resumen del contenido incluido en la página 9
OPERATING INSTRUCTIONS INSTALLATION OF LOGS GENERAL GLASS INFORMATION & BURNER LAVA ROCK Only ceramic glass approved by Vermont 1 . Remove front glass. (See "Glass Removal" section) Castings Majestic Products Company may 2. Remove logs from packaging. be used for replacement on this unit. 3. Place rear log (KR4) on rear bracket (ensure log is 1. The use of substitute glass will void all product seated properly, leveled and centered to the unit), so it warranties. will not move from side to side
Resumen del contenido incluido en la página 10
MAINTENANCE LARGE LAVA ROCK PLACEMENT a. It is important to keep the burner and the burner The large lava rock provided with this fireplace must be compartment clean. This must be done periodically, placed on the firebox base on either side of the burner at least once per season. (See Cleaning Procedure). assembly. b. Clean the brass trim using a soft clean cloth, slightly dampened with lemon oil and buff with a soft clean Under no circumstances should these cloth. Do NOT use brass polish or
Resumen del contenido incluido en la página 11
I O L L FLAME ADJUSTMENT FLAME CHARACTERISTICS Flame adjustment is accomplished by rotating the Hi/Lo It is important to periodically perform a adjustment knob located near the centre of the gas visual check of the pilot and the burner control. (Fig. 18) flames. Compare them to the pictorials illustrated below (Fig.19 and 20). If any of the flames appear abnormal call a Turn service person. Turn clockwise counterclockwise to lower to increase flame height. flame height. SIT Pilot 3/8" - 1/2" S
Resumen del contenido incluido en la página 12
O HI ON T O LIGHTING AND OPERATING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This fireplace has a pilot which must be lit manually. • If you cannot reach your gas supplier, call the When lighting the pilot follow these instructions Fire Department exactly. C. Use only your hand to push in or turn the gas B. BEFORE LIGHTING smell all around
Resumen del contenido incluido en la página 13
TROUBLE SHOOTING THE GAS CONTROL SYSTEM SIT 820 MILLIVOLT VALVE Note: Before trouble shooting the gas control system, be sure external gas shut off is in the "On" position. WARNING: BEFORE DOING ANY GAS CONTROL SERVICE WORK, REMOVE GLASS FRONT. SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION 1. Spark ignitor will not light A. Defective or misaligned Using a match, light pilot. If pilot lights, turn off pilot and electrode at pilot. push the red button again. If pilot will not light - check gap at
Resumen del contenido incluido en la página 14
TROUBLE SHOOTING THE GAS CONTROL SYSTEM HONEYWELL MILLIVOLT VALVE START CHECK • GAS SUPPLY ON NO • SUPPLY LINE HOOKED UP • SHUTOFF VALVE OPEN • LOCKOUT HAS ENGAGED. WAIT YES 60 SECONDS AND TRY AGAIN. • FOR SPARK AT ELECTRODE WHILE DEPRESSING PIEZO — 1/8" GAP TO PILOT LIGHTS WITH PILOT HOOD NEEDED. NO PIEZO IGNITOR • ALL WIRING CONNECTIONS • REPLACE PIEZO IGNITOR YES • FOR AIR IN THE LINES • THERMOPILE NEEDS A MINIMUM 325mV. ADJUST PILOT FLAME HEIGHT. • ALL WIRING CONNECTIONS.
Resumen del contenido incluido en la página 15
O L REPLACEMENT PARTS 35 10a/b 12 19 18 30 15 16 31 14 24 20 a/b 8 32 11 a/b 25 27 28 13 18 9 a/b 17 34 29 26 3 2 21 33 22 OFF 23 a/b IRHEDV32 10003929 15 PILOT ON PILOT ADJ I H
Resumen del contenido incluido en la página 16
REPLACEMENT PARTS LIST Description IRHEDV32 1 Log Set Complete 57896 1a Log Ember Front KR1 1b Log Front Left KR2 1c Log Front Right KR3 1d Log Rear KR4 1e Log Top Left KR5 1f Log Top Right KR6 2 Lava Rock (Package) 10001454 3 Burner Lava Rock (Package) 57897 4a Burner Complete With Tiles (Nat.) 10000198 4b Burner Complete With Tiles (Prop.) 57904 5 Ceramic Tile (Single) 57803 6a Orfice Front Burner (Nat.) SEE RATING PLATE FOR ORIFICE SIZE 6b Orfice Front Burner (Prop.) SEE RATING PLATE FOR ORIF
Resumen del contenido incluido en la página 17
A-TRIM OPTIONS FOR RHEDV32 IMPORTANT: Only Trim Panel Assemblies approved by Vermont Castings Majestic Products Company can be used. A1) RHESS, RHESL, RHESSD, RHESLD & RHESXL TRIMS FRAME ASSEMBLY RHESS, RHESL, RHESSD, RHESLD and RHESXL 1. Lay Trim Top Facing and Trim Side Facings, face down Trim Top Deflector on to an even surface such as a table or floor. Be sure not to scratch the painted surfaces. Trim Frame Top Section 2. Install the nuts and bolts (Fig. 21). Side View 10/24 Fig. 24 SCREWS
Resumen del contenido incluido en la página 18
FRAME MOUNTING GENERAL INFORMATION The Decorative Front Frame should be installed last after all other work, such as gas connections, venting, etc., has been completed and thoroughly checked and tested for operation, leaks and proper installations requirements. Fit Decorative Frame to the fireplace and fasten (Fig. 25). SCREWS AS SHOWN FROM FRONT Fig. 25 Plastic on the trim must be removed before mounting onto the fireplace. Glass must be tightly pressed against the front of the frame in order
Resumen del contenido incluido en la página 19
TRIM REPLACEMENT PARTS LIST All repair parts will be available from your local dealer. When ordering, always give the following information: Model and serial number, part description with finish and part number; (2) (3) (3) (3) (4) KEY DESCRIPTION RHESS RHESL RHESSD RHESLD RHESXL 1 Trim Frame Top, Flat Black 57929 57932 57929 57932 57935 2 Trim Frame Left, Flat Black 57927 57930 57927 57930 57933 3 Trim Frame Right, Flat Black 57928 57931 57928 57931 57934 (1) 4 Trim Top Deflector 17634 17634 17
Resumen del contenido incluido en la página 20
A2) RHEBSL & RHEBXL TRIMS RHEBXL TRIM ASSEMBLY To install the kit you do not have to remove any piece RHEBSL of brass, you just add the external pieces. 1. Install trim channels (left and right sides). Use two Remove the frame trim from the unit if it is already screws to assemble each piece. installed. 2. Slide on the trim top channel and fasten it from the back side. 1. Install trim channels (left and right sides)by removing 3. Install the trim top deflector and use two screws to the two screw
