Resumen del contenido incluido en la página 1
Vermont Castings, Majestic Products: DVR33
INSTALLER/CONSUMER
SAFETY INFORMATION
PLEASE READ THIS MANUAL
BEFORE INSTALLING AND
USING APPLIANCE
WARNING!
IF THE INFORMATION IN THIS
MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR EXPLO-
Rear Vented
SION MAY RESULT CAUSING
PROPERTY DAMAGE, PER-
Direct Vent Gas Fireplace
SONAL INJURY OR LOSS OF
LIFE.
Model:
DVR33
FOR YOUR SAFETY
Installation and service must
be performed by a qualified
installer, service agency or
the gas supplier.
WHAT TO DO IF YOU SMELL
Resumen del contenido incluido en la página 2
Vermont Castings, Majestic Products: DVR33 Table of Contents PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING THE APPLIANCE. Thank You and Congratulations on Your Purchase of a Vermont Castings, Majestic Products Fireplace. IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and will void the warranty. Installation and Operating Instructions Important Curing/Burning Inst
Resumen del contenido incluido en la página 3
Vermont Castings, Majestic Products: DVR33 Installation and Operating Instructions This gas appliance should be installed by a qualified installer PROPOSITION 65 WARNING in accordance with local building codes and with current CSA- Fuels used in gas, wood-burning or oil fired appliances, B149.1 Installation codes for Gas Burning Appliances and and the products of combustion of such fuels, contain Equipment. If the unit is being installed in a mobile home, the chemicals known to the State of Ca
Resumen del contenido incluido en la página 4
Vermont Castings, Majestic Products: DVR33 Fireplace Dimensions C L S 4" Dia. (102mm) Rough E Opening 7" Dia. (178mm) Depth L G O F Recessed Nailing Flange B\," (16mm) Rough Opening Width 33Z\x" Z\x" (13mm) L Rough Opening M Height 1" (25mm) P B H B C R Electrical Gas Line T Access Access (102mm) 4" I - U D 2" (52mm) 1" 2" J A (25mm) (52mm) K Q Fig. 2 Fireplace specifications and framing dimensions. Appliance Dimensions A 33” 838 mm 7 B28 /8” 733 mm 3 C16 /8” 416
Resumen del contenido incluido en la página 5
Vermont Castings, Majestic Products: DVR33 Clearance to Combustibles Appliance Top 0” (0 mm) Bottom 0” (0 mm) Side 0” (0 mm) Mantel Leg Back 0” (0 mm) J Venting I H Black Surround Face G Concentric sections of DV Vent 1” (25 mm) F Non-concentric sections of DV Vent Sides and bottom 1” (25 mm) Top 2” (50 mm) K L M N Mantels O The height that a combustible mantel is fitted above the fireplace is dependent on the depth of the mantel. Side of Combustion Chamber This also applies to the distance bet
Resumen del contenido incluido en la página 6
Vermont Castings, Majestic Products: DVR33 Framing and Finishing Final Finishing Noncombustible materials such as brick or tile may be Check fireplace to make sure it is extended over the edges of the face of the appliance. levelled and properly positioned. DO NOT cover the window frame assembly, any 1. Choose the unit location. vent, louvre assembly top or louvre assembly bottom. 2. Place the unit into position and secure it to the floor If a Trim Kit is going to be installed on the fireplace,
Resumen del contenido incluido en la página 7
TP TPTH TH Vermont Castings, Majestic Products: DVR33 Gas Line Installation Remote ON/OFF Switch Installation Do not wire the remote ON/OFF wall When purging the gas lines, the front switch for this gas appliance into a 120 V glass must be removed. power supply. The gas pipeline can be brought in through the side of 1. Thread the wiring through the electrical knockout the fireplace as well as the bottom. Knockouts are located on either side of the unit. Take care not to provided on the bottom
Resumen del contenido incluido en la página 8
Front of Unit Vermont Castings, Majestic Products: DVR33 EB-1 Electrical Box Inside Electrical Box The fireplace, when installed, must be Retaining Screw electrically connected and grounded in accordance with local codes or, in the absence of local codes, with the current CSA C22.1 Canadian Electrical Code For USA installations, follow the local codes and the national electrical code ANSI/NFPA No. 70. Outside It is strongly suggested that EB-1 Electrical Junction Box wiring be carried out by a
Resumen del contenido incluido en la página 9
LO Vermont Castings, Majestic Products: DVR33 Electronic Gas Control Valve This appliance may be fitted with a Honeywell Ignition Module. To install the remote On/Off starter switch on electronic ignition units (Fig. 10): PILOT 1. Thread the wiring through the holes on the side panels of the appliance. Take care not to cut the HONEYWELL IGNITION MODULE wire or insulation on metal edges. Route the wire 24V MV MV/VP PV GRD 24V SENSE SPARK to a conveniently l
Resumen del contenido incluido en la página 10
V V Operable Vermont Castings, Majestic Products: DVR33 General Venting Information–Termination Location INSIDE CORNER DETAIL G V N H N A D E B C B Fixed Fixed L V B V Closed Closed V Fixed Operable G Closed F V V B M V G B J X B I K X V V A A VENT TERMINATION AIR SUPPLY INLET AREA WHERE TERMINAL IS NOT PERMITTED V X CFM145a 1 2 Canadian Installations US Installations A = Clearance above grade, veranda, porch, 12 in. (30 cm) 12 in. (30 cm) deck or balcony B = Clearance to window/door that may b
Resumen del contenido incluido en la página 11
Vermont Castings, Majestic Products: DVR33 Termination Clearances Termination clearances for buildings with combustible and noncombustible exteriors. Inside Corner Recessed Location Outside Corner D B = C C Combustible A = 6"(152mm) Combustible E A 6"(152mm) Noncombustible V V 2"(50mm) Noncombustible 2"(50mm) V B Balcony - Balcony - with no side wall with perpendicular side wall C = Maximum depth of 48" (1219mm) for recessed H G location. V V D = Minimum widt
Resumen del contenido incluido en la página 12
Vermont Castings, Majestic Products: DVR33 Twist Lock Pipes Max. 20" When using Vermont Castings, Majestic Products (508 mm) twist-lock pipe it is not necessary to use sealant on the joints. The only areas of the venting system that need to be sealed with high temperature silicone sealant are the collars on the fireplace and termination, and the sliding joint of any telescopic vent section used in Top view flat installation the system. To join twist lock pipes together, simply align the beads
Resumen del contenido incluido en la página 13
Vermont Castings, Majestic Products: DVR33 Vent Opening — Finished Combustible Wall Wall (240mm) These ends 9C\," These ends screwed to should be even appliance Vent 10C\," Termination (254mm) (framing detail) Vent Opening — Noncombustible Wall 7Z\x" (190mm) CFM116 FP1005 Fig. 16 Vent opening, side wall. Fig. 18 Flat to the wall installation. 12" (304.8 mm) max. #8 Screws (2) #8 Screws (2) Firestop (Side View) CFM135a Fig. 17 Zero clearance sleeve. Step 4 Install the 4” (100 mm) vent to
Resumen del contenido incluido en la página 14
Vertical Dimension From The Floor Of the unit To The Centre Of The Horizontal Vent Pipe Vermont Castings, Majestic Products: DVR33 How To Use the Vent Graph Vertical Sidewall Application The Vent Graph should be read in conjunction with the Since it is very important that the venting system following vent installation instructions to determine the maintain its balance between the combustion air relationship between the vertical and horizontal intake and the flue gas exhaust, certain limitations
Resumen del contenido incluido en la página 15
Vermont Castings, Majestic Products: DVR33 As shown in Fig. 22, the total of dimension A and B is Max. 3' not to be greater than 17’ (5.2 m). (914 mm) • The maximum number of 45˚ elbows permitted per side wall installation is two (2). These elbows can be installed in either the vertical or horizontal run. • For each 45˚ elbow installed in the horizontal run, the length of the horizontal run MUST be reduced by 18” (45 cm). This does not apply if the 45˚ elbows are installed on the vertical part
Resumen del contenido incluido en la página 16
Vermont Castings, Majestic Products: DVR33 Vertical Sidewall Installation Step 1 Locate vent opening on the wall. It may be necessary to first position the fireplace and measure to obtain hole location. Depending on whether the wall is X combustible or noncombustible, cut opening to size. (For combustible walls, frame in opening first (Fig. 24). Combustible Walls: Cut a 9C\,”H x 9C\,” W (240 mm x 240 mm) hole through the exterior wall and frame. Noncombustible Walls: Hole opening must be 7Z\x”
Resumen del contenido incluido en la página 17
Vermont Castings, Majestic Products: DVR33 If installing a snorkel, a minimum 24” (610 mm) vertical X High Temperature rise is necessary. The maximum horizontal run with the Sealant 24” (610 mm) vertical pipe is 36” (915 mm). This measurement is taken from the collar of the fireplace (or transition elbow) to the face of the exterior wall. See the Sidewall Venting Graph for extended horizontal run if the vertical exceeds 24” (610 mm). 1. Establish vent hole through the wall (Fig. 24, page 16). 2
Resumen del contenido incluido en la página 18
Vermont Castings, Majestic Products: DVR33 If the foundation is recessed, use recess brackets (not • Up to two 45° elbows may be used within the supplied) for securing lower portion of the snorkel. horizontal run. For each 45° elbow used on the Fasten brackets to wall first, then secure to snorkel with horizontal plane, the maximum horizontal length self drilling #8 x 1/2 sheet metal screws. It will be must be reduced by 18” (450 mm). necessary to extend vent pipes out as far as the Example: Ma
Resumen del contenido incluido en la página 19
Vermont Castings, Majestic Products: DVR33 Vertical Through-the-Roof Installation Typical Ceiling 1. Locate your fireplace. Support Application 2. Plumb to center of the (4”) flue collar from ceiling Typical above and mark position. Roof 3 3 3. Cut opening equal to 9 /8” x 9 /8” (240 mm x Support Application 240 mm). 4. Proceed to plumb for additional openings through the roof. In all cases, the opening must provide a FP1184 minimum of 1 inch clearance to the vent pipe, i.e., 3 3 the hole must
Resumen del contenido incluido en la página 20
Vermont Castings, Majestic Products: DVR33 DVR33 Bracket Restricter Installation NOTES: When installing DVR33 with a vertical through-the-roof configured flue system, the bracket restricter supplied with the appliance (part# 10002910) should be fitted to the appliance at installation. For DVR33 numbers A12H00, A12I00, A14A00 and A14B00 only, the restricter plate for the vertical termination (part# 10003246) must be installed for vertical runs over 20’ (6.1 m). Fitting the Bracket Restricter Fi
