Resumen del contenido incluido en la página 1
OWNER'S MANUAL
Water Softener
With High Performance Valve
IntelliSoft 370 Series
MODEL NO. 625.383760
Caution:
• Warranty
Read and follow all safety rules and operating
• Installation
instructions before first use of this product.
Timer
• Start Up / Setting
Questions ?
• How It Works
Visit www.KenmoreWater.com
or call toll free 1-800-426-9345 (M - F, 7 AM - 8 PM CST)
• Care Of
Repair or Parts ? Call toll free 1o8004694663
• Specifications
See back cover for other Sears service numbers.
• Repair
Resumen del contenido incluido en la página 2
WARRANTY ON WATER SOFTENER ONE YEAR LiMiTED WARRANTY ON WATER SOFTENER When installed, operated and maintained according to all instructions supplied with the product, if this Kenmore appliance fails due to a defect in material and workmanship within one year from the date of pur- chase, call 1-800-4-MY-HOME ®to arrange for free repair. THREE YEAR LIMITED WARRANTY ON ELECTRONIC PARTS When installed, operated and maintained according to all instructions supplied with the product, if any of the fo
Resumen del contenido incluido en la página 3
TABLE OF CONTENTS Safety Guides ................................................................................................................................................. 4 Unpack and Check Shipment ........................................................................................................................ 5 Plan Your Installation: Tools Needed, Materials Needed ........................................................................... 6-10 Install Inlet/Outlet Adapters or By
Resumen del contenido incluido en la página 4
A Read all steps, guides and rules carefully before installing and using your new water softener. Follow all steps exactly to correctly install. Failure to follow them could cause personal injury or property damage. Reading this book will also help you to get all of the benefits from your water softener. Your Kenmore Water Softener will remove hardness minerals from water. This is measured in A grains per gallon (gpg). It will also remove some clear water iron*. This is measured in parts per mil
Resumen del contenido incluido en la página 5
iNSPECT SHIPMENT Your water softener is shipped complete in one carton. Use care when handling the softener. DO NOT turn upside down. DO NOT drop, or set on sharp objects that could make a hole in the bottom. The water softener is heavy, do not try to lift it or move more than is necessary. Remove all items from your shipping carton. Check all items against the packing list below. Note any items lost or damaged in shipment. Note any damage to the shipping carton. Refer to the exploded view and p
Resumen del contenido incluido en la página 6
PLAN YOUR INSTALLATION It is recommended to read through the entire manual before beginning your installation. Follow all steps exactly. Reading this manual will also help you get all the benefits from your system. TOOLS NEEDED: • Safety glasses • Flathead screw driver • Phillips screw driver • Adjustable slip joint pliers • Tape measure or ruler J Flathead Screwdriver Safety Glasses Phillips Screwdriver Adjustable Slip Joint Pliers Tape Measure or Ruler ADDITIONAL TOOLS NEEDED FOR THE FOLLOWING
Resumen del contenido incluido en la página 7
outside faucet (hard water) - outside faucet (hard water) soft, col-----_ _ to R.O. faucet water ¢- ___ _ _ter Line _ __ soft, hot I _ _-:"_-'___-"% water • o_r Line -_4:_ [T_ soft wa er / Shu -offII toR ...... t / . -V lve p..'--.jj o :to:,sIt water hard i i storage heater _ _ _::::Y wat:rartd° // _ tank J I I llI1 house // water /# gap _ softener floo/ main "_ drain FIG. 3 Typical Installation WHERE TO INSTALL THE WATER SOFTENER Review the following points before you choose a place to put your
Resumen del contenido incluido en la página 8
Suggested Slab Foundation Installation outside - hard Plug the softener transformer into an inside, 120 volt 60Hz electrical outlet. If an outside For outside hard outlet is used, be sure it has water, trench under- approved weather protection. ground as needed. outside - hard WATER SOFTENER (install in garage, car port, or other sheltered area) water in Run drain tubing to laundry tub or p-trap inside home, if possible. FIG. 4 Otherwise, run to a dry well. DRAW IN YOUR PIPES AND FITTINGS Your H
Resumen del contenido incluido en la página 9
PIPE, FITTINGS, OTHER MATERIALS NEEDED You must first decide how to run "in" and "out" pipes to the softener. Look at your house main water pipe at the OUT IN point you will connect the softener. Is the pipe soldered copper, glued plastic, or threaded galvanized or brass? 1" NPT sweat What is the pipe size? What kind of pipe and fittings is it Useteflontape, adaptor (2)* easiest for you to work with, and what tools do you have? pipe or both. 1" NPT adaptor 2 of each Now look at the common plans
Resumen del contenido incluido en la página 10
BEFORE iNSTALLiNG CHECKS & TESTS if you have a well water system, look at the pressure Your water supply needs to be checked for chemical gauge to find the water pressure. Call your local water analysis, water pressure and water flow rate. To accom- department if you have city water. They will tell you what plish this, complete the following steps: the water pressure is where you live. Check Water's Chemical Analysis: Sears sells a com- NOTE: Add these readings to the Facts and Figure plete line
Resumen del contenido incluido en la página 11
ASSEMBLE INLET OUTLET ADAPTORS, Shutoff Shutoff . Pressure OR SINGLE BYPASS VALVE Valve Valve ,z/ Tank Complete the following steps to assemble the adaptors or bypass valve. 1. Close the shutoff valve on the house main water pipe, near the water meter or pressure tank, to turn off the water. See Fig. 7. Pump 2. Shut off the gas or electric supply to the water heater. See Fig. 7. 3. Open the highest and lowest water faucets in your Electrical Panel house. This will let water drain from the pipes.
Resumen del contenido incluido en la página 12
iNSTALLiNG HOLDING CLIPS Black Clip Cross Section of Valve Bypass Valve or Installation Adaptor Inlet or Outlet Before installing the bypass valve, or copper tube, be sure the turbine and X support are firmly in place in the valve outlet port. Turbine \, Support Sensor Port O-Ring Clip Snaps into Place Between Larger Diameter Rings FIG, 11 BYPASS VALVE TURNED DOWNWARD Turbine FiG. 10 Turn bypass valve upside down to connect to floor level plumbing. OUT 3 VALVE BYPASS INSTALLING 3 VALVE BYPASS AN
Resumen del contenido incluido en la página 13
POSITION SOFTENER INTO PLACE Complete the following steps to position the softener. MOVE SOFTENER INTO PLACE 1. Grip under the ridge on the salt tank sidewall. 2. Carefully rock back and forth into position. 3. Move the softener into position. 4. Place on a level and smooth surface. If needed, put a piece of 3/4" plywood, at least 17" x 20", under the Grip under ridge tank. Then put spacers under the plywood to level the to move softener. softener. See Fig. 14. NOTE: Do not put shims or spacers
Resumen del contenido incluido en la página 14
CONNECTTHEVALVEDRAINHOSE per tube is also best to use for an overhead drain. Use a copper drain tube if the softener is installed outside, Takea lengthof 3/8"insidediameter draintubingand or in the sunlight. Heat from the sun can soften, flatten attachoneendto thedrainfitting.SeeFig.16.Usea and close up some kinds of tubes. tubeclampto holdit inplace.Puttheotherendofthe tubingoverafloordrain,intoa laundry tub,standpipe, To adapt a copper drain tube to the softener, buy a orothersuitable drain.Ch
Resumen del contenido incluido en la página 15
LEAK TEST To check for leaks, complete the following steps: HOUSE MAIN WATER SHUTOFF VALVES CAUTION: To avoid water or air pressure dam- age to softener inner parts, and to flush pipe chips or other residue from the water pipes, be Shu_ sure to do the following steps exactly as instructed. Sh t ff Vale --_:_= Pressure Tank Meter 1. Fully open two cold, soft water faucets near the softener. Water 2. Look at the pictures in Fig. 18 and 19 to deter- Well Pump mine your kind of bypass valve(s). Plac
Resumen del contenido incluido en la página 16
INSTALLGROUNDINGCLAMPBETWEEN COLD WATER PiPE GROUNDING THE SOFTENER IN AND OUT PIPES The house cold water pipe (iron or copper) is often TO Valve Inlet used to ground all electrical outlets in the home. Outlets are grounded to protect you from shock when Ground you touch any electric appliance plugged into the out- let. If you installed the single bypass valve, the cold Clamp (2% water pipe ground is broken. See Fig. 20 and 21. IMPORTANT." Be sure the cold water pipe has direct metal to metal co
Resumen del contenido incluido en la página 17
INSTALLCOVERS Salt Hole Afterinstalling yourwatersoftener, replace thecovers. Angle Cover Cover thecoverssothemaincoverclipsontothebackfirst,then (Main) bringdowninfrontandcliponthetwo(2)tabsinsidetherim ofthesaltholeandlowerthesaltcoverclosed. SeeFig.23. RESTART THE WATER HEATER Turn on the gas (or electric) supply to the water heater and light the pilot. YOUR PLUMBING INSTALLATION AND ELECTRICAL WORK ARE NOW COMPLETE. FiG. 23 REGENERATION Button Salt Level Adjust Display UP Button -- DOWN Butt
Resumen del contenido incluido en la página 18
SET PRESENT TiME OF DAY _l,lq wq_M 'UU If the words PRESENT TIME do not show in the display, PRESENTTIME PRESENT TIME press the SELECT1 button until they do show in the dis- play. Press the UP or DOWN buttons to set the present time. Press UP to move the display ahead; press DOWN to move the time backward. If the present time is between FIG. 26 noon and midnight, be sure PM shows. If the present time is between midnight and noon, be sure AM shows. Each press of the UP or DOWN buttons changes the
Resumen del contenido incluido en la página 19
SANiTiZETHE WATER SOFTENER Salt Hole Care is taken at the factory to keep your water softener clean and sanitary. Materials used to make the softener will not infect or contaminate your water supply, or cause bacteria to form or grow. However, during shipping, storage, installing \ and operating, bacteria could get into the softener. SANITIZE YOUR WATER SOFTENER AS FOLLOWS: 1. Be certain the bypass valve is pulled out to Brinewell Cover "service" position. (Remove and 2. Lift the salt hole cover
Resumen del contenido incluido en la página 20
ADDINGSALTTOTHE STORAGETANK Brine(saltdissolved inwater)isneeded foreachand every regeneration. The water for making brine is metered into the salt storage tank by the softener. You must keep salt in the tank, but because the water soften- er is very efficient, it is not necessary to keep it full. Especially in humid areas, it is best to fill the storage tank one quarter to one half full, and to add salt more often. Salt bridging occurs more often when conditions are humid. Use NUGGET or PELLET
