Resumen del contenido incluido en la página 1
Programming
Tumble Dryer
UniLinc Control
Refer to Page 4 for Model Identification
TMB1276C
TMB1276C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 70444801R3
www.comlaundry.com July 2011
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
Introduction......................................................................................... 4 Table of Model Identification ............................................................................. 4 Nameplate Location.............................................................................. 4 Contents Preliminary Information.................................................................... 5 About the Control .................................................................
Resumen del contenido incluido en la página 4
Menu Navigation................................................................................. 18 The UniLinc.......................................................................................... 18 Menu to Menu Navigation ............................................................... 18 Screen to Screen Menu Navigation.................................................. 18 Menu Navigation with Parameters................................................... 18 Cycle Name and Banner Editing...
Resumen del contenido incluido en la página 5
Auto Ignition Retry (Gas Models Only)............................................... 37 Air Flow Switch Errors......................................................................... 37 Airflow Switch Sensed Closed While Not In Run Mode ................ 37 Airflow Switch Does Not Close After Cycle Started ...................... 37 Airflow Switch Bounces During A Running Cycle......................... 37 Rotation Sensor Error ......................................................................
Resumen del contenido incluido en la página 6
Introduction Model Identification Information in this manual is applicable to these models: Gas Steam/Thermal Oil Electric UA025L UT025L UU025L UT025S UU025S UT025E UU025E 25 Pound UA025N UT025N UU025N UA030L UT030L UU030L UT030S UU030S UT030E UU030E 30 Pound UA030N UT030N UU030N UA035L UT035L UU035L UT035S UU035S UT035E UU035E 35 Pound UA035N UT035N UU035N UA050L UT050L UU050L UT050S UU050S UT050E UU050E 50 Pound UA050N UT050N UU050N UT050T UU050T UA055L UT055L UU055L UT055E UU055E 55 Pound No
Resumen del contenido incluido en la página 7
Preliminary Information Audit Information About the Control The control collects and stores audit information, The UniLinc control on the tumbler is an advanced, which can be accessed with a PDA, PC or network. graphical, programmable computer that lets the owner Refer to the following list for some of the available control most machine features by interacting with the audit information. Refer to UniLinc PC and PDA control. Application User Instructions. UniLinc allows the owner to prog
Resumen del contenido incluido en la página 8
Preliminary Information IR Communications Menu Medium (M) Temperature = 160 (°F) Low (L) Temperature = 140 (°F) Very Low (VL) Temperature = 120 (°F) Cool Down Temperature = 100 (°F) Cool Down Time = 2 (minutes) Rapid Advance = Disabled Multi-Segment Cycles = Disabled LCD Backlight ON/OFF = On Banner # 1 = Blank Banner # 2 = Blank PHM1003R Daylight Saving = Enabled Figure 2 Key Pad Audio = Enabled The IR Communications Menu displays while the control is communicating with a PDA. The control En
Resumen del contenido incluido en la página 9
UniLinc Identification Operational Keypad The control includes seven keypads. These functions are available to the operator and are intended to control and manage operation of the tumbler. Refer to Figure 4 and Table 1. TMB1276C Figure 4 Keypad Description Press to move the cursor on display and to edit programming values. Also, press while in Cycle Menu or Run Menu to change to the Contrast Adjust/Backlight LCD/UP ARROW Menu. Also, press with and to enter System Menu. Press to move the
Resumen del contenido incluido en la página 10
UniLinc Identification Operation Modes In the Cool Down segment, pressing the keypad will decrease the remaining time by one minute. General Modes of Operation When the cycle is completed, the audit counter, Total In each mode of operation, the user may press keypads Rapid Advance Cycles is incremented rather than the or communicate with the control to change the Total Machine Cycles audit counter. In addition this displayed menu. cycle is recorded in the audit list “Last 25 Machine Cycle
Resumen del contenido incluido en la página 11
UniLinc Identification End of Cycle Mode Reversing Mode (reversing models only) The control enters End of Cycle Mode after the cool Models equipped with the reversing feature will rotate down segment is finished. The display will show a in the forward direction, pause, rotate in the reverse graphic prompting the user to open the loading door. If direction and then pause for programmable times and the door has not been opened or a keypad has not been segments of the cycle. Factory default reve
Resumen del contenido incluido en la página 12
Machine Cycle Definition and Operation There are 41 machine cycles that can be selected and Rotation Sensor Equipped run. Machine cycles can be modified or made Machines “unavailable” by manually editing them in Modify Cycle Menu or by using the PDA or network to On machines equipped with a rotation sensor, the download a modified machine cycle into the control. control monitors the rotation sensor to verify the Machine cycles cannot be deleted, but can be made cylinder is rotating. The
Resumen del contenido incluido en la página 13
Machine Cycle Definition and Operation To Start a Cycle Press any keypad to clear the menu and return to the Cycle Menu. 1. Press the or keypad to change cycles. Optional settings are performed by either pressing a keypad or by a combination of keypad presses: 2. Press the keypad to move the cycle in the right most menu box to the center, highlighted • Press the keypad to jump control to the position. Contrast Adjust/Backlight Menu. 3. Press the keypad to move the cycle in the • Press the
Resumen del contenido incluido en la página 14
Machine Cycle Definition and Operation Run Menu Run Menu provides cycle and segment information while the machine is operating. Refer to Figure 6. 1 10 2 Cycle01: Towels 3 6 Time Dry Segment01 7 4 180 F 5 30:00 9 Run Menu 8 TMB1302R TMB1302R 1 Cycle Number and Name 7 Heat / No Heat Indicator 2 Cycle Type (and Material Type for Moisture 8 Menu Indicator Sensing Models) 9 Cycle Time Remaining (or Cycle Progress 3 Segment (Number or Cool Down) Indicator for Auto-Dry Cycle Type and Moisture 4 Prog
Resumen del contenido incluido en la página 15
Machine Cycle Definition and Operation Contrast/Backlight Menu Close Door Menu Contrast Backlight Contrast / Backlight Menu TMB1303R PHM1008R Figure 8 Figure 7 The Close Door Menu displays when loading door or lint door on the machine is open and needs to be Press the keypad from Cycle Menu or Run Menu closed. to enter the Contrast Adjust/Backlight Menu. The Contrast Adjust/Backlight Menu allows the user to Close door or press the keypad to return to Cycle adjust contrast and turn the bac
Resumen del contenido incluido en la página 16
Machine Cycle Definition and Operation Run Diagnostic Menu While machine is running, press the keypad to enter Run Diagnostic Menu. Press the , , or keypad to navigate the menu. Refer to Diagnostics section for Temp and Inputs and more description of these menus. Moisture Outputs Press the keypad to choose selection. The keypad will stop the cycle. If the keypad is pressed, display enters Run Alarms Machine ID Menu. If nothing is selected for 15 seconds, the display will return to Run Menu.
Resumen del contenido incluido en la página 17
Machine Cycle Definition and Operation Temp and Moisture Menu 1 Cycle01: Towels 2 Moisture Dry: Cotton 4 3 05:00 Segment01 Temp Moisture Custom 5 155 F Actual 35% Save 11 Program 160 F 7% 7 6 8 Run Menu 9 TMB1305R 10 TMB1305R 1 Cycle Number and Name 8 Programmed Moisture Content (Moisture 2 Cycle Type and Material Type (Moisture Sensing Models only) Sensing Models only) 9 Menu Indicator 3 Segment (Number or Cool Down) 10 Cycle Progress Indicator / Cycle Time 4 Segment Time Elapsed Remaining
Resumen del contenido incluido en la página 18
Machine Cycle Definition and Operation Cycle Stopped Menu Error Menu Cycle Stopped Fan Motor Contactor Error Press START Key to Resume Press STOP Key to Abort Cycle Press STOP Key to Abort Cycle TMB1357R TMB1307R Figure 11 Figure 13 The Cycle Stopped Menu will be displayed in Pause The Error Menu will be displayed as a result of an error during a cycle, the Test Cycle or while on the Mode. Press to resume the cycle or to Cycle Menu. abort the cycle and go to the Open Door Menu. If a fat
Resumen del contenido incluido en la página 19
Machine Cycle Definition and Operation Open Door Menu Load Sensed Menu Extended Tumble in 0:50 Is the machine basket empty? Yes No TMB1364R Figure 16 The Load Sensed Menu will show from the Cycle TMB1340R Menu only after eleven minutes of Idle Mode, without Figure 14 user interaction, having consistently sensed a load for that entire period. The menu prompts to the operator to The Open Door Menu is displayed from the Run Menu indicate whether the machine basket is empty. No is prior to a
Resumen del contenido incluido en la página 20
Menu Navigation Cycle Name and Banner Editing The UniLinc This Edit Mode is used when a cycle name must be The front-end control allows the user to control modified or a banner created. The highlighted box is machine operation and programming by pressing keypads to select options on the display menus and by moved over the editable item and the keypad is navigating between display menus. pressed. The mode can be verified by seeing the first character in the item with a blinking underscore
