Manual de instrucciones de Life Fitness R9i

Resumen del contenido incluido en la página 1



   


 


Resumen del contenido incluido en la página 2

Congratulations... and welcome to the world of Life Fitness and the Life Fitness R9i & R7i Recumbent Exercise Bikes. The following Parts Identification Listing and the step by step assembly procedures have been assembled to make the set-up of the Recumbent Exercise Bikes as quick and easy as possible. Please take special note of the following important points prior to choosing a location and beginning assembly of the Recumbent Exercise Bikes.

Resumen del contenido incluido en la página 3

IMPORTANT SAFETY INSTRUCTIONS! ⇒ DO NOT locate the Recumbent Exercise Bike outdoors, near swimming pools, or in areas of high humidity. ⇒ DO NOT operate your Recumbent Exercise Bike if it has been dropped, damaged, or even partially immersed in water. Contact Life Fitness Customer Support Services at the number in the Operation Manual. ⇒ DO NOT locate the Recumbent Exercise Bike any closer than 30 inches (76 cm) to a television set. ⇒ DO NOT locate additional Recumbent Exercise Bike any

Resumen del contenido incluido en la página 4

TOOLS REQUIRED FOR ASSEMBLY...Phillips screwdriver, 3/16" hex key wrench, T-40 Torx wrench PARTS DESCRIPTION 1 Seat Back Screw Qty: 4 2 Seat Back Washer Qty: 4 0017-00101-1131 0017-00104-0253 3 Console support assembly Bolt Qty: 4 4 Console Screw Qty: 4 0017-00101-1737 0017-00101-1253 5 Seat Back Qty: 1 6 Console Support Assembly Qty: 1 AK39-00003-0000 7 Display Console Qty: 1 8 Accessory Tray Assembly (If so equipped) Qty: 1 9 Left Pedal Strap Qty: 1 10 Right Pedal Strap Qty: 1 11 9V Battery (M

Resumen del contenido incluido en la página 5

7 11 8 4 6 5 9 3 2 1 10

Resumen del contenido incluido en la página 6

1. Slide the ACCESSORY TRAY (#8) (if so equipped) over the user right seat back post and down to make contact with the SEAT HANDLEBAR. 2. Position the underside clamp bracket (A) around the SEAT HANDLEBAR and tighten the two clamp SCREWS and WASHERS (B). NOTE: BE CAREFUL NOT TO OVER-TIGHTEN THE SCREWS. MISE EN GARDE : VEILLER À NE PAS TROP SERRER LA VIS. 3. Align the four holes in the SEAT BACK (#5) with those in the SEAT BACK POSTS. Insert the four SCREWS (#1) and WASHERS (#2) through the backs

Resumen del contenido incluido en la página 7

9. Carefully feed the wires back into the top of the CONSOLE SUPPORT ASSEMBLY (#6) and attach the DISPLAY CONSOLE (#7) to the CONSOLE SUPPORT ASSEMBLY using the four CONSOLE SCREWS (#4) and a Phillips H screwdriver. Tighten the four SCREWS in a criss-cross pattern. NOTE: BE CAREFUL NOT TO OVER-TIGHTEN THE SCREWS. G J MISE EN GARDE : VEILLER À NE PAS TROP SERRER LA VIS. 10. After placing the exercise bike in the intended location for use, check the stability of the bike. If the exercise bike is n

Resumen del contenido incluido en la página 8

PRE-OPERATION CHECKLIST
Ensure that the console support screws are tight.
Make sure the Recumbent Exercise Bike is properly leveled and stable.
Ensure that the Leveler Jam Nuts are tight.
Read the entire Operation Manual before using the Recumbent Exercise Bike. Before attempting to operate your Recumbent Exercise Bike, it is imperative that you familiarize yourself with the contents of the Operation Manual. If your Recumbent Exercise Bike does not respond as described in the OPERATI