Resumen del contenido incluido en la página 1
REAR BLADE &
LANDSCAPE RAKE
RBC60
LRC60
Tested. Proven. Unbeatable.
MAN0169
Rev. 3/09/2010
OPERATOR'S MANUAL
Resumen del contenido incluido en la página 2
TO THE DEALER: ® Assembly and proper installation of this product is the responsibility of the Woods dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies that all Dealer Check List items have been completed. Please contact your dealer to com
Resumen del contenido incluido en la página 3
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSIDE FRONT COVER SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 4
SPECIFICATIONS RBC60 LRC60 Overall Width 60 inches 60 inches Weight 182 lbs. 177 lbs. Moldboard Thickness 7-gauge ----------- Cutting Edge 1/2" x 6" x 60" Reversible ---------- Teeth ---------- 30 - 5/16" x 1" HT High Carbon Tines Position 360° Pivot 360° Pivot Offset - Left or Right 12 inches ----------- Angle - Left or Right 15° or 30° 15° or 30° Pitch Adjustment Controlled by top link Controlled by top link Tractor Rating Max. Engine 25 hp Max. Engine 25 hp Tractor 3-Point Cat 0 or 1 Cat 0 o
Resumen del contenido incluido en la página 5
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! fastened. Falling off power unit can result in death Safety is a primary concern in the design and from being run over or crushed. Keep foldable manufacture of our products. Unfortunately, our ROPS systems in “locked up” position at all times. efforts to provide safe equipment can be wiped Make sure all safety decals are installed. out by an operator’s single careless act. Replace if damaged. (See Safety Decals section for In additi
Resumen del contenido incluido en la página 6
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) MAINTENANCE Do not stop, start, or change directions sud- Before dismounting power unit or performing denly on slopes. any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point Use extreme care and reduce ground speed on hitch and all raised components to the ground, slopes and rough terrain. operate valve levers to release any hydraulic pres- sure,
Resumen del contenido incluido en la página 7
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! 4 5 3 2 5 1 CD6154C 4 2 3 1 5 - 20106 Red Reflector (2 x 4-1/2) (Rev. 8/26/2005) MAN0169 (Rev. 5/6/2005) Safety 7
Resumen del contenido incluido en la página 8
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 1 - Serial Number Plate 4 - 1004299 WARNING MODEL NO. SERIAL NO. Woods Equipment Company Oregon, Illinois, U.S.A. 3 - 1002941 WARNING 2 - 1004250 FALLING OFF WARNING CAN RESULT IN BEING RUN OVER. TO AVOID SERIOUS CRUSHING AND Tractor must be equipped INJURY OR DEATH: with ROPS (or ROPS CAB) PINCHING HAZARD Read Operator's Manual and seat belt. Keep foldable Be extremely
Resumen del contenido incluido en la página 9
OPERATION The operator is responsible for the safe operation of 3. Connect tractor top link by inserting tractor clevis this equipment. Operators must be instructed in and be pin into top hitch point on rear blade frame capable of the safe operation of the equipment, its assembly and secure (Figure 2). attachments and all controls. Do not allow anyone to operate this equipment without proper instructions. This equipment is designed for a wide range of applica- tions. The blade may be used for sc
Resumen del contenido incluido en la página 10
3. Connect tractor top link by inserting tractor clevis pin into lower hitch point on rear blade frame assembly and secure (Figure 4). CD6625 4 3 2 1 1. Hitch pin 2. 7/8 Flat washer 3. 7/8 Lock washer Figure 3. Lower Lift Arm Attachment, Category 0 4. 7/8 Hex nut Figure 5. Hitch Pin Kit (Optional) OPERATING TECHNIQUES Level the A-frame and boom with 3-point connecting links and top link. Adjusting the top link length will change the fore and aft pitch of the tool. Lengthening the top link will
Resumen del contenido incluido en la página 11
Only offset blade when operating in light material such as sand, loose soil, or snow. CD6161B 11 CD6156-1 20 11. Parking stand 20. 1/4 x 2-1/2 Lock pin Figure 6. Moldboard Offset Left Figure 7. Parking Stand - Operating Position Backfilling Storage Position Reverse blade for backfilling ditches or trenches (see 1. Raise tractor 3-point lift arms. Reversing). 2. Remove parking stand from operating position The rake may also be used in light backfilling applica- (Figure 7). tions. 3. Align top
Resumen del contenido incluido en la página 12
PRE-OPERATION CHECK LIST (Owner’s Responsibility) ___ Review and follow all safety rules and safety decal instructions on pages 5 through 8. ___ Check that all safety decals are installed and in good condition. Replace if damaged. ___ Check that all hardware is properly installed and secured. ___ Check that equipment is properly and securely attached to tractor. ___ Do not allow riders. ___ Make sure tractor ROPS or ROPS cab and seat belt are in good condition. Keep seat belt securely fastened d
Resumen del contenido incluido en la página 13
MAINTENANCE The information in this section is written for operators Reverse Cutting Edge who possess basic mechanical skills. If you need help, 1. Remove plow bolts (27 & 28), hardened flat washer your dealer has trained service technicians available. (25), and hex nuts (24). For your protection, read and follow all safety informa- tion in this manual. 2. Remove cutting edge (4) from moldboard and reverse cutting edge with sharp edge down. Re- install hardware previously removed. Bef
Resumen del contenido incluido en la página 14
TAIL WHEEL ADJUSTMENT LRC60 CLEANING (OPTIONAL) After Each Use 1. Raise rake until tail wheels clear the ground. ● Remove large debris such as clumps of dirt, grass, 2. To raise tail wheels, remove klik pin (10) and crop residue, etc. from machine. washer (17). Allow clevis and shaft (7) to slide ● Inspect machine and replace worn or damaged down in tail wheel arm (9). Do not remove shaft parts. completely from wheel arm. ● Replace any safety decals that are missing or not 3. Rotate height adj
Resumen del contenido incluido en la página 15
ASSEMBLY INSTRUCTIONS DEALER SET-UP INSTRUCTIONS Assemble Blade Assembly of this Rear Blade/Landscape Rake is the Attach Pivot Assembly to Moldboard responsibility of the WOODS dealer. It should be deliv- 1. Remove two plow bolts (28) from center moldboard ered to the owner completely assembled, lubricated (5) and cutting edge. and adjusted for normal cutting conditions. 2. Remove two carriage bolts (26) from top of The Rear Blade/Landscape Rake is shipped partially moldboard. assembled. Assembl
Resumen del contenido incluido en la página 16
4.Secure rear blade frame assembly to pivot 24 assembly using pivot cap (3), two hardened flat washers (25), and hex nuts (24). 25 5. Place rear blade frame assembly in desired 3 8 position and secure with hitch pin (8). 9 6. Place parking stand in the down position to support rear blade. See page 11 for storage. 24 CD6155B-2 25 3 8 1 9 1. Tine beam 3. Pivot cap 8. Hitch pin 9. Rear blade frame assembly 24. 5/8 NC Hex nut 6 CD6155A -1 25. 5/8 Hardened flat washer Figure 14. Landscape Rake Assem
Resumen del contenido incluido en la página 17
DP4 9 12 13 9. Tail wheel arm 12. 1/2 Flange lock nut 13. 1/2 NC x 1-3/4 Cap screw GR5 Figure 17. Skid Shoe Installed (Right Side) Figure 15. Caster Wheel Installed Quick Hitch Bushing Kit (Optional) Install Optional Skid Shoe Kit (Rear Blade) 5 1. Remove plow bolts from each end of cutting edge. 6 4 3 2. Attach skid shoe bracket (1) to rear of moldboard with plow bolt (2), washer (3), and hex nut (4) supplied in kit. 3. Adjust skid shoe to desired height. 4. Repeat steps for opposite side of
Resumen del contenido incluido en la página 18
Manual Storage Tube Kit (Optional) NOTE: May need to drill 2 - 9/32 (.281") holes 7- 1/2" apart. 1. Slide two clamps (3) onto manual tube. Attach caps (2) to either end of the manual tube. 2. Attach manual tube to frame using two self tapping screws (4) and clamps (3) in the holes previously drilled. 2 3 1 CD6626 4 3 2 1. Manual tube 2. 2.00 ID x 1.00 Cap 3. 2.00 dia Pipe clamp 4. 5/16 NC x 3/4 Self tapping screw Figure 19. Manual Storage Tube Kit 18 Assembly MAN0169 (Rev. 5/6/2005)
Resumen del contenido incluido en la página 19
DEALER CHECK LISTS PRE-DELIVERY CHECK LIST DELIVERY CHECK LIST Inspect the equipment thoroughly after assembly to ___ Show customer how to make adjustments. ensure it is set up properly before delivering it to the ___ Instruct customer how to lubricate and explain customer. importance of lubrication. The following check lists are a reminder of points to ___ Point out the safety decals. Explain their meaning inspect. Check off each item as it is found satisfactory and the need to keep them in pla
Resumen del contenido incluido en la página 20
RBC60/LRC60 ASSEMBLY 9 8 34 - Safety Decal Set, Complete 35 - Decal set LRC/RBC, Complete 24 25 24 25 3 31 29 20 30 10 11 6 26 5 24 25 24 25 28 3 4 27 CD6156B 1 2 22 23 MAN0169 (Rev. 5/6/2005) 20 Parts
