Resumen del contenido incluido en la página 1
+00EH99677601_01EN_remo_IM.book Page 1 Thursday, October 8, 2009 4:12 PM
REMOTE CONTROLLER FOR AIR CONDITIONER (SPLIT TYPE)
Installation Manual
Remote Controller
Model name:
Wireless remote controller kit
TCB-AX21UL
Wireless remote controller
Generic model name
and Signal receiving unit
TCB-AX21UL WX-TA01UES
(Wireless remote controller
model name)
Installation Manual
Remote controller for air
English
conditioner (Split type) 1
Manuel du proprietaire
Télécommande pour climatiseur
Wireless
Resumen del contenido incluido en la página 2
+00EH99677601_01EN_remo_IM.book Page 1 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit Thank you very much for purchasing TOSHIBA/Carrier Remote Controller for Air Conditioner. Please read the owner's manual carefully before using your Remote Controller for Air Conditioner. • Be sure to obtain the “Owner’s manual” and “Installation manual” from constructor (or dealer). Request to constructor or dealer • Please clearly explain the contents of the Owner’s
Resumen del contenido incluido en la página 3
+00EH99677601_01EN_remo_IM.book Page 2 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 1 ACCESSORY PARTS No. Parts Quantity Signal receiving unit 1 1 (provided 7.9” (200 mm) power cable) 2 Mounting bracket 1 3 Screws ∅0.16” x 1.0” (M4 x 25 mm) 2 4 Screws ∅0.16” x 1.6” (M4 x 40 mm) 2 5 Wood screws 2 6 Spacer 4 7 Wire joints 2 8 Cable tie 1 Pattern template 9 1 3.7” x 2” (95 mm x 51 mm) 10 Remote controller 1 11 Remote cotroller holder 1 Truss tapping screw
Resumen del contenido incluido en la página 4
1 2 3 4 5 6 +00EH99677601_01EN_remo_IM.book Page 3 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 2 SWITCH LOCATION OF SIGNAL RECEIVING UNIT Signal receiving unit Screw Face plate Remove the face plate from Signal receiving unit. Remove Address selector switch This switch is used to address one of a maximum of six air conditioners that can be controlled by the remote controller. (Refer to page 11.) All /NORMAL selector switch Set this switch to the “
Resumen del contenido incluido en la página 5
+00EH99677601_01EN_remo_IM.book Page 4 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 3 INSTALLATION LOCATION OF SIGNAL RECEIVING UNIT • Do not install in a location where the air contains oil mist, such as in a kitchen or factory. • Do not install next to a window, or in any other location directly exposed to sunlight and outside air. • Do not install nearby devices which can be expected to produce electrical noise, such as elevators, automatic doors,
Resumen del contenido incluido en la página 6
1 2 3 4 5 6 +00EH99677601_01EN_remo_IM.book Page 5 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 4 HOW TO INSTALL THE SIGNAL RECEIVING UNIT NOTE • To avoid malfunction of the remote controller, do not assemble or run remote control wiring together with the power cables, and do not enclose them in the same metal conduit. • When the power unit induces electrical noise, it is recommended that a noise filter or the like be installed. For flush mounting i
Resumen del contenido incluido en la página 7
1 2 3 4 5 6 +00EH99677601_01EN_remo_IM.book Page 6 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 2. In order to later pass the Signal receiving 0.08”-0.12” Notch where Signal Cable tie unit wiring out through the upper case (thin (2–3 mm) receiving unit cord part at the top center), use nippers or a passes through top case similar tool to cut a notch in the same size as the Signal receiving unit cord (optional). (Fig. B) Signal receiving Connecto
Resumen del contenido incluido en la página 8
+00EH99677601_01EN_remo_IM.book Page 7 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 4. Use bracket parts (A) and (B) to securely grip the ceiling Part (A) material. (Fig. E) 5. Connect the Signal receiving unit wire (2-core) to the wire from the indoor unit. (Refer to “Wiring the Signal receiving unit.”) Check the terminal number on the indoor unit before wiring the Signal receiving unit and be sure not to wire incorrectly. (The unit will be damage
Resumen del contenido incluido en la página 9
+00EH99677601_01EN_remo_IM.book Page 8 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 5 HOW TO PERFORM CABLING OF THE SIGNAL RECEIVING UNIT Flush Mounting Connection diagram Indoor unit remote Signal receiving unit controller terminal board Power wire from Wire of Signal receiving Signal receiving unit unit (Field procurement) 2 (AWG20 (0.5 mm )) (UL wires rated 300 V) Connector Provided wire joint (WHT 2) 1. Strip the insulation to approximately 0.5
Resumen del contenido incluido en la página 10
+00EH99677601_01EN_remo_IM.book Page 9 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 6 REQUIREMENT The control by two remote controllers is enabled by installing the wireless remote controller with the wired remote controller for an indoor unit. (Max. 2 remote controllers of wireless or wired are insatiable.) “2-remote controllers” controlling means that one or multiple units are operated by the multiple remote controllers. NOTE 1. Upon confirmation of
Resumen del contenido incluido en la página 11
+00EH99677601_01EN_remo_IM.book Page 10 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit To operate a group control of multiple indoor units by 2 remote controllers MAIN and SUB remote controllers are operable even if they are installed to any indoor unit. (Total cable length: Within 656’2” (200 m)) Remote controller inter-unit Wired remote Wireless remote cable for group control controller (SUB) controller kit (Field procurement) 2 (AWG20 (0.5 mm )) (S
Resumen del contenido incluido en la página 12
1 2 3 4 5 6 +00EH99677601_01EN_remo_IM.book Page 11 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 8 HOW TO SET THE ADDRESS SWITCH • When the multiple Signal receiving units are installed in the same room, an address can be set to prevent cross communication. • When replacing the battery and pushing ACL button, the address of the remote controller becomes [ALL] and the Signal receiving unit is enabled to receive signal regardless of setting of address
Resumen del contenido incluido en la página 13
+00EH99677601_01EN_remo_IM.book Page 12 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 10 SELF-DIAGNOSIS TABLE AND MEASURES Lamp indication of Signal receiving unit : Goes off : Blink (0.5-sec. interval) Lamp indication Cause Measures Power supply is not turned on. Check cable Miscabling between Signal receiving unit connection and correct it. and indoor unit No indication even if the remote controller is operated. Defective connection between Signal
Resumen del contenido incluido en la página 14
+00EH99677601_01EN_remo_IM.book Page 13 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 12 EXPLANATION TO CUSTOMERS • Hand over the “Owner’s Manual” and “Installation Manuals” to the customer after installation works. • Explain usage and maintenance of the remote controller according to “Owner’s Manual”. 13 HOW TO HANDLE THE REMOTE CONTROLLER In case using remote controller mounting to the wall, etc. Check a signal is received correctly by Mounting scre
Resumen del contenido incluido en la página 15
+00EH99677601_01EN_remo_IM.book Page 14 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 14 TEST RUN Before test run • Before turning on the power supply switch, carry out the following procedure. 1 Using 500V-megger, check 1M Ω or more exists between the terminal block 1 to 3 and the earth. If 1M Ω or less is detected, do not run the unit. Do not apply to the remote controller circuit. 2 Check the valve of the outdoor unit being opened fully. • To protect
Resumen del contenido incluido en la página 16
+00EH99677601_01EN_remo_IM.book Page 15 Thursday, October 8, 2009 4:12 PM 85464369216000 (EH99677601)
