Resumen del contenido incluido en la página 1
www.hampton-fi re.com
Owners &
H35 Direct Vent Gas Fireplace
Installation Manual
MODELS: H35-NG1 Natural Gas H35-LP1 Propane
WARNING: FOR YOUR SAFETY
If the information in these instructions are not followed ex- What to do if you smell gas:
actly, a fi re or explosion may result causing property damage, Do not try to light any appliance
Do not touch any electrical switch:
personal injury or loss of life.
do not use any phone in your
FOR YOUR SAFETY
building.
Do not store or us
Resumen del contenido incluido en la página 2
® HAMPTON Direct Vent Freestanding Gas Stove To the New Owner: Congratulations! ® You are the owner of a state-of-the-art Hampton Gas Stove by FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. The H35 is a hand crafted appliance and has been designed to provide you with all the warmth and charm of a wood fi replace at the fl ick of a switch. The model H35 has been approved by Warnock Hersey for both safety and effi ciency. As it also bears our own mark, it promises to provide you with economy, com
Resumen del contenido incluido en la página 3
TABLE OF CONTENTS Unit Dimensions ............................................................2 Conversion Kit to Lower BTU Rating ...........................31 Brick Panel ..................................................................32 Log Set Installation ......................................................32 SAFETY LABEL Double Door Installation ..............................................34 Decorative Door Grill Installation .................................34 Copy of Safety Label .
Resumen del contenido incluido en la página 4
SAFETY LABEL ® This is a copy of the label that accompanies NOTE: Hampton units are constantly being each Direct Vent Freestanding Gas Stove. improved. Check the label on the unit and if We have printed a copy of the contents here there is a difference, the label on the unit is for your review. the correct one. COPY OF SAFETY LABEL For the State of Massachusetts, installation and repair must be done by a plumber or gasfi tter licensed in the Commonwealth of Massachusetts. For the State of Ma
Resumen del contenido incluido en la página 5
REQUIREMENTS MA Code - CO Detector (for the State of Massachusetts only) 5.08: Modifications to NFPA-54, Chapter 10 (2) Revise 10.8.3 by adding the following additional requirements: (a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished gr
Resumen del contenido incluido en la página 6
INSTALLATION Home Construction and Safety Standard, Title AIR PASSAGEWAYS OF THE AP- IMPORTANT MESSAGE 24 CFR, Part 3280, or the current Standard PLIANCE BE KEPT CLEAN. of Fire Safety Criteria for Manufactured SAVE THESE Home Installations, Sites, and Communities INSTRUCTIONS ANSI/NFPA 501A, and with CAN/CSA Z240-MH DUE TO HIGH TEMPERATURES, Mobile Home Standard in Canada. THE APPLIANCE SHOULD BE The Direct Vent Freestanding Gas Stove must be LOCATED OUT OF TRAFFIC AND installed in
Resumen del contenido incluido en la página 7
INSTALLATION 8) Any safety glass removed for servicing 8) Final check. Refer to the "Final Check" sec- manufactured home the unit must be bolted down to the fl oor. must be replaced prior to operating the ap- tion. pliance. 4) This appliance is Listed for bedroom instal- Before leaving this unit with the customer, lations when used with a Listed Millivolt 9) To prevent injury, do not allow anyone who the installer must ensure that the appli- is unfamiliar with the operation to use the a
Resumen del contenido incluido en la página 8
INSTALLATION LOCATING YOUR OPTIONAL FAN INSTALLATION GAS STOVE Fan Kit Contains: 7) Install locking grommet to power cord and When selecting a location for your stove, ensure Qty. Description push through hole in the rear panel and give that the clearances listed above are met as well 1 Fan Speed Controller with nut, and a 1/4 turn to secure. as ensuring that there is adequate accessibility knob. for servicing and proper operation. 1 Fan Assembly c/w green wire NOTE: When runnin
Resumen del contenido incluido en la página 9
INSTALLATION VENTING INSTALLATION VENT RESTRICTOR INTRODUCTION PRECAUTIONS POSITION The Horizontal Termination Kit and the Simpson These venting systems are engineered products Vent restriction is required for certain venting Dura-Vent Direct Vent System Model DV-GS installations, see the diagrams in "Venting that have been designed and tested for use venting systems, in combination with the Direct with the H35-NG1, and H35-LP1. The warranty Arrangment" section to determine if they are Ven
Resumen del contenido incluido en la página 10
INSTALLATION EXTERIOR VENT TERMINAL LOCATIONS ® 10 Hampton H35 Direct Vent Freestanding Gas Stove A= Clearance above grade, veranda, porch, deck, or balcony *(min. 12"/30cm) J= Clearance to service regulator vent outlet *(min. 36"/90cm) B= Clearance to window or door that may be opened *(12"/30cm) K= Clearance to non-mechanical air supply inlet to building or the combustion air inlet to C= Clearance to permanently closed window *(min. 12"/30cm) any other appliance *(12"/30cm) D= Vertical cleara
Resumen del contenido incluido en la página 11
INSTALLATION RIGID PIPE VENTING COMPONENTS LIST All Simpson Dura-Vent components are available directly from FPI. ® Description Simpson Dura-Vent Selkirk Amerivent Security ® TM ® Direct VentGS Direct-Temp Direct Vent Secure Vent 6" Pipe Length, Galvanized 908 4DT-6 N/A SV4L6 6" Pipe Length, Black 908B 4DT-6B N/A SV4LB6 7" Pipe Length, Galvanized N/A N/A 4D7 #N/A 7" Pipe Length, Black
Resumen del contenido incluido en la página 12
INSTALLATION RIGID PIPE VENTING SYSTEMS Horizontal or Vertical Terminations Vertical Termination Alternate Cap Horizontal Termination Storm Collar Caps Vinyl Siding Standoff (Optional) Flashing Horizontal Termination Ceiling Firestop Cap Wall Thimble Pipe Length Adj.Pipe Length 11" - 14-5/8" o 90 Elbow WARNING: 24" Pipe Length Do not combine venting components from different venting systems. TM However use of the the AstroCap and FPI Riser is acceptable with all systems. This product has b
Resumen del contenido incluido en la página 13
INSTALLATION O ROTATING 45 ELBOW FOR STRAIGHT HORIZONTAL TERMINATIONS o 2) Rotate the elbow 180 1) Remove all 4 screws that secure the elbow to the unit using a 1/4" 3) Secure the elbow by securing magnetic nut driver. it with the 4 screws. Remove all 4 screws and washers VENTING ARRANGEMENTS Vertical Terminations Systems for Horizontal Terminations for All Residential Manufactured and Mobile Homes Venting Systems The shaded areas in the diagram below show The shaded area in the diagram
Resumen del contenido incluido en la página 14
INSTALLATION VENTING ARRANGEMENTS HORIZONTAL TERMINATIONS USING RIGID PIPE The two diagrams show all allowable com- binations of straight horizontal termination using Rigid Pipe. Restrictor position "A". Dura-Vent Snorkel Termination Riser Vent Termination Venting Arrangements -Straight Horizontal Termination at a De-Rated BTU The diagrams show all allowable combina- tions of straight horizontal termination using Rigid Pipe. Restrictor position "A". Refer to the "Conversion Kit to Lower BTU
Resumen del contenido incluido en la página 15
INSTALLATION o Horizontal Venting with Two (2) 90 Elbows o o One 90 elbow = Two 45 elbows. Option V H + H1 With these options, maxi- A) 3' Min. 2' Max. mum total pipe length is 30 feet with minimum of 8 feet B) 4' Min. 3' Max. total vertical and maximum C) 5' Min. 4' Max. 8 feet total horizontal. D) 6' Min. 5' Max. Please note minimum 1 o E) 7' Min. 6' Max. foot between 90 elbows H1 is required. F) 8' Min. 8' Ma
Resumen del contenido incluido en la página 16
INSTALLATION o Vertical Venting with Two (2) 90 Elbows o o One 90 elbow = Two 45 elbows. Option V H V + V1 With these options, max. total pipe length is 30 feet with min. A) 1' Min. 3' Max. 2' Min. of 6 feet total vertical and max. B) 2' Min. 4' Max. 3' Min. 7 feet total horizontal. C) 3' Min. 5' Max. 4' Min. Please note min. 1 foot o D) 4' Min. 6' Max. 5' Min. between 90 elbows is required. E) 5' Min. 7' Max. 6' Min. V1 Lengths do not include elbow in
Resumen del contenido incluido en la página 17
INSTALLATION VERTICAL TERMINATION WITH CO-LINEAR FLEX SYSTEM Masonry chimneys may take various contours which the fl exible liner will accommodate. However, THE APPLIANCE MUST NOT BE CONNECTED TO A CHIMNEY FLUE keep the fl exible liner as straight as possible, avoid unnecessary bending. SERVING A SEPARATE SOLID FUEL BURNING APPLIANCE. The Air Intake pipe must be attached to the inlet air collar of the termination cap. Alternate Approved Caps This appliance is designed to be attached to Require
Resumen del contenido incluido en la página 18
INSTALLATION DV STOVE HORIZONTAL VENT KIT DV 2 ft. Stove Vent Kit (Part # 946-116) and DV 4 ft. Stove Vent Kit (Part #946-216) includes all the parts needed to install the H35 Direct Vent unit with minimum horizontal and vertical vent dimensions. For installations that require longer vertical and/or horizontal vents use the Dura-Vent system as shown in the "Dura-Vent Termination Kit" and "Dura-Vent Venting Components" sections. Qty. Description 1) 1 Rigid Pipe Section (Kit # 946-11
Resumen del contenido incluido en la página 19
INSTALLATION 13) Secure the 4" dia. fl ex liner with adapter onto the stove collar. Put a bead of Mill-Pac around the appliance adapter and secure with 3 screws (#8 x 1/2, stainless steel). o 14) Attach the 45 elbow onto the starter collar by sealing with Mill-Pac and/or high tem- perature silicone and securing with 3 of the #8 x 1/2" (black) screws. o 15) Attach the pipe section to the 45 elbow by sealing with Mill-Pac and/or high tempera- ture silicone and securing with 3 of the #8 x 1/
Resumen del contenido incluido en la página 20
INSTALLATION DURA-VENT TERMINATION KIT thimble is suitable for 2 x 4 or 2 x 6 wall construc- decks, windows, soffi ts, gas regulators, air sup- Planning Your Dura-Vent tion.) Select the amount of vertical rise desired for ply inlets and public walkways as specifi ed in Installation "vertical-to-horizontal" type installations. the "Exterior Vent Terminal Locations" section and in your local building codes. There are two basic types of Dura-Vent Direct Warning: Always maintain required Vent S
