Resumen del contenido incluido en la página 1
SHR Series
Woodburning Fireplace
Homeowner's Installation
and Operating Manual
For Models:
SHR36
SHR42A
SHR48
SHR52
1384
Underwriter's Laboratories Report No. MH6018
SHR cover
5/27/99 djt
DO NOT DISCARD THIS MANUAL: Retain for future use.
20001384 12/06 Rev. 18
Resumen del contenido incluido en la página 2
SHR Series Woodburning Fireplace Safety Information PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING FIREPLACE. IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and will void the warranty. Description Do not install a solid fuel burning insert or other products not specified for use with this fireplace. The SHR Series fireplaces are solid fuel, woodburn- ing fireplaces. The SHR36/42A/4
Resumen del contenido incluido en la página 3
SHR Series Woodburning Fireplaces SHR36 Series Woodburning Fireplace Rough ��" (737mm) ���" (19mm) Opening Depth 13 ���" Dia. 57�����" (1472mm) ����� " (340mm) (2264mm) ����� " 11" Dia. (680mm) ���" ( 279mm) ���" Rough Opening Width 47 ���" (1213mm) Rough Opening Height ���" 12���" (318mm) 48���" (1226mm) ����� " �� " Outside (397mm) Gas Line 44" (610mm) Air 36" (1118mm) Access (914mm) 13���" �����" 7���" (349mm) (189mm) (197mm) ����� " Gas Line Access 46���" (1175mm) (368mm) FP526A Fig.
Resumen del contenido incluido en la página 4
SHR Series Woodburning Fireplace SHR48 Series Woodburning Fireplace ��" (1041mm) ���" (19mm) Rough Opening Depth 13 ���" Dia. 66���" (1686mm) �����" (340mm) (264mm) ����� " 11" Dia. (680mm) ���" (279mm) ���" Rough Opening Width 59 ���" (1518mm) Rough Opening Height ���" 12���" (318mm) Outside 15 ���" ����� " Gas Line 48" Air (397mm) (724mm) Access (1219mm) 13 ���" 7���" �����" (349mm) (189mm) (197mm) 14���" Gas Line Access 58���" (1480mm) (368mm) FP545A Fig. 3 SHR48 Series specification
Resumen del contenido incluido en la página 5
SHR Series Woodburning Fireplaces Front Width Back Width Depth A B C B SHR36 35 ³⁄₄" 22" 20 ³⁄₈" (908 mm) (559 mm) (516 mm) SHR42A 41 ⁷⁄₈" 26 ⁵⁄₈" 23 ³⁄₈" C (1064 mm) (676 mm) (594 mm) SHR48 47 ³⁄₄" 34" 20 ¹⁄₄" (1213 mm) (864 mm) (514 mm) SHR52 52" 34 ¹⁄₂" 25 ¹⁄₄" (1321 mm) (876 mm) (641 mm) FP1531 Fig. 4a Hearth dimensions. FP1531 hearth dimensions Chase Installation 9/04 djt Insulation methods shown are optional for cold climate, not a requirement for unit operation. T
Resumen del contenido incluido en la página 6
SHR Series Woodburning Fireplace Chimney Requirements - Offset Installations Of fset Chimney Flue Exit Rise Chimney Section FP282 Elbow 30° 30˚ Elbow Offsets IWF282 Return Elbow MBUF B G A 5/26/96 1' Offset 1 ¹⁄₂' 3' 4' Rise G 0 0 0 0 0 3" 11" 30° D Offset 1 0 0 0 0 8 ¹⁄₄" 20" E Elbow 0 1 0 0 0 11 ¹⁄₄" 25¹⁄₄" Rise 6 FT. 11CS Sup- 2 0 0 0 0 13 ¹⁄₂" 29¹⁄₄" port C 30° 1 1 0 0 0 16 ¹⁄₂" 34¹⁄₄" Return H Offset 0 0 1 0 0 20 ¹⁄₄" 40³⁄₄" Elbow 2 1 0 0 0
Resumen del contenido incluido en la página 7
SHR Series Woodburning Fireplaces Planning Information Preplanning an installation is very important to ensure The Ten Foot Rule safety and to save time and money. An installer must predetermine where a fireplace will be set and how the Major U.S. building codes specify a minimum chimney chimney system will be run. height above the roof top. The “Ten Foot Rule” is a fire safety rule and not a draft rule. To ensure proper draft, Mounting the Fireplace it is recommended that you always meet o
Resumen del contenido incluido en la página 8
SHR Series Woodburning Fireplace Chimney Supports Installation The chimney system is supported by the fireplace for vertical chimney heights less than 30 feet above the Insulating Fireplace hearth. Chimney supports are required if the vertical Enclosure for Cold Climates height exceeds 30 feet with 11CF chimneys. Locate If you live in a cold climate, it is not required but chimney supports at ceiling holes or other structural highly recommended that you insulate the fireplace framing at
Resumen del contenido incluido en la página 9
SHR Series Woodburning Fireplaces Rear Firebrick Brick Retainer Hard, Flat Surface Side Firebrick Front Notch FP1234 Fig. 11 SHR52 Firebrick installation. 3. Slide the rear firebrick back into the left corner be- hind the end of the left firebrick. Push both panels back FP1234 Insulation as far as possible into the left side and corner. SHR52 4. Swing the right side of the back firebrick into place. Firebrick Attach the left brick in place using a brick retainer at the Platform 12/10/02
Resumen del contenido incluido en la página 10
SHR Series Woodburning Fireplace CAUTION: REPORT TO YOUR DEALER ANY PARTS Chimney Centerline DAMAGED IN SHIPMENT, SPECIFICALLY CHECK THE END CONNECTION OF CHIMNEY SECTIONS Actual Centerpoint AND ELBOWS. 11 ¹⁄₈" NOTE: SHR Series Fireplaces must use CFM Corpora- (283 mm) tion model 11CF, 11 inch, 2 wall chimney systems. The installation procedure described in this manual applies only to the 11CF system, chimney components may not be mixed. Straight-Up Chimney Installation To mark the center
Resumen del contenido incluido en la página 11
SHR Series Woodburning Fireplaces The inside dimension of the frame must be the same as the hole size selected from Figure 11 in order to provide the required 2 inches of air space between the outside diameter of the chimney and the edges of the framed ceiling hole. Metal Safety Strips (1, 2 or 3 pieces) 17 ¹⁄₂" 17 ¹⁄₂" Existing (445 mm) Ceiling (445 mm) Joists Fire- "Z" Safety place Strip Chimney (not supplied) Hole 1/2" Min. Plat- Overlap Hearth Ext. ����" form FP557a Fig. 16 Safety
Resumen del contenido incluido en la página 12
SHR Series Woodburning Fireplace Support Structure Open Closed Elbow Strap (must be tight) Ceiling Hole ELBOW STRAP Framing Angle Firestop FP710a Fig. 18 Outside air operation. ANGLED STRAP Chimney Support Strap Installing the Chimney System (must be tight) FP270/271 FP270/271 Start by attaching the first chimney section to the collar Fig. 20 Attach straps to a structural framing member CR Series . on top of the fireplace. 2/19/99 djt FP710a SHR OUTSIDE AIR LEVER Installing the Firestop
Resumen del contenido incluido en la página 13
SHR Series Woodburning Fireplaces Ceiling Installation Attic Installation Nails (4) Joist Firestop Spacer Firestop Joist Spacer Flange Down Into Hole Nails (4) Flange Up Into Hole FP285 Fig. 21 Installing firestop spacer. IWF285 Cut and Frame Roof Hole Continue Installing Pipe to Complete Run mbuf 5/25/96 Size of roof hole varies with the type of chimney termi- Continue attaching pipe sections to complete system nation installed. Refer to installation instructions pro- to next level alw
Resumen del contenido incluido en la página 14
SHR Series Woodburning Fireplace Installing Chimney in a Chase Air Space Clearances Combustible framing material MUST NOT pen- Refer to Page 5, Figure 4 for an illustration of a typical etrate AIR SPACE (shaded areas) chase installation. CAUTION: Treatment of firestop spacers and construc- tion of chase may vary with type of building. These instructions are not a substitute for local building codes. 2" You must check your local building codes to determine Standoff specific requirements for
Resumen del contenido incluido en la página 15
SHR Series Woodburning Fireplaces Mantel Clearance - Mantel Clearance - with Noncombustibel Facing Material No Noncombustible Facing Material Combustible 12" 12" Mantel and Trim Combustible Mantel (305mm) (305mm) Finished Wall Finished Wall and Trim Max. Max. Header Header 1 ��� " 1��� " Ledge Bracket Ledge Bracket 12" 12" (305mm) Noncombustible (305mm) Noncombustible Material min. Material min. Surround Surround Face Face 6" * Noncombustible Facing (159mm) Material Min. * Minimum width
Resumen del contenido incluido en la página 16
SHR Series Woodburning Fireplace Stud Finished Wall 2 x 4 Finished Noncombustible Header Decorative Fac- ing Covered Wall CAUTION: Do Not Screen Rail Must be Sealed with Ledge Bracket Place Finishing Ma- Noncombustible terial Beyond These Material Edges or Cover Air Hearth Inlets FP1168 Surround FP1167 Fig. 27 Finishing front of fireplace. Fig. 26 Facing on fireplace surround flush with finished wall. Face Plate FP1167 FP1168 facing flush finishing front with finished wall 12/20/01 djt 12/
Resumen del contenido incluido en la página 17
SHR Series Woodburning Fireplaces The top of insulation must be covered with a noncom- Side Wall Protection bustible decorative covering or a piece of .018” mini- Adjacent combustible side walls that are within dimen- mum sheet metal, to protect hearth extension material. sions shown in Figure 29 of fireplace opening must be (Fig. 31) protected with Wall Shield Model SP40 or a specifically Secure the hearth extension to the floor to prevent built wall shield described in Figure 28. shifting,
Resumen del contenido incluido en la página 18
SHR Series Woodburning Fireplace Minimum Wall Clearances Minimum Hearth Extension Dimensions (for On-Site Construction) WITH WITHOUT Noncombustible Noncombustible Surround Facing Surround Facing Shaded area starts G G 1/2" away from 4" Brick H edge of unit (Example material) 4" J Firebox E E Seal cracks F** D Opening between the May install fireplace C** A - Min. clearance noncombustible and hearth to combustible decorative extension with perpendicular wall covering noncombustible OR .018"
Resumen del contenido incluido en la página 19
SHR Series Woodburning Fireplaces removed from gas line tube to repack space around the Wall Covering 2 x 4 Header pipe. Material should be inserted from outside of the - Do Not Notch at fireplace and packed tightly to totally seal between the Ledge Brackets Fig. 22 or 23 pipe and tube. Note: Gas pipe should not come in contact with any Hearth Extension wood structures until it has reached a point at least one (1) inch away from fireplace side. Hearth Extension Insulation NOTE: When in
Resumen del contenido incluido en la página 20
SHR Series Woodburning Fireplace 12 13 2 7 1 b c 8 d a 6 9 5 4 3 10 11 CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice. SHR36/42A/48/52 Woodburning Fireplace For units FH30RO, GH40RO, HH30RO, IH10RO 1384 pts Item/Model Number SHR36 SHR42A SHR48 SHR52 replacement parts 1. Damper Weld Assembly RP210 RP210 RP210 n/a 2. Damper Handle 20001418 20001418 20001418 20005322 5/27/99 djt 3.
