Resumen del contenido incluido en la página 1
Operation manual
for model VR2300
Record All Information
for future reference:
Purchase Date:
Model #:
Serial #:
Questions? 1-800-888-2468
Learn more about your pressure
washer and register on line at
www.VR2300.com
Pressure Washer
IMPORTANT
Please make certain that the person who is to use this equipment
carefully reads and understands these instructions before operating.
Part No. D27935 Rev. 1 4/30/03
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS OPERATING INSTRUCTIONS.........10-14 SAFETY GUIDELINE/DEFINITIONS .......2 MAINTENANCE................................15-16 CONSUMER SAFTEY INFORMATION...2 STORAGE...............................................17 IMPORTANT SAFETY INSTRUCTIONS ...................................3-6 TROUBLE SHOOTING GUIDE........18-19 CONSUMER GENERAL AND SERVICE WARRANTY............................................20 INFORMATION .........................................6 QUICK FACTS.............
Resumen del contenido incluido en la página 3
IMPORTANT SAFETY INSTRUCTIONS Read Operation Manual. Do not operate equipment until you have read Operation Manual for Safety, Assembly, Operation, and Maintenance Instructions. READ AND SAVE THESE INSTRUCTIONS HAZARD RISK OF EXPLOSION OR FIRE WHAT CAN HAPPEN HOW TO PREVENT IT Spilled gasoline and it’s vapors can be- Shut off engine and allow it to cool before come ignited from cigarette sparks, adding fuel to the tank. electrical arcing, exhaust gases, and hot Use care in filling tank to
Resumen del contenido incluido en la página 4
HAZARD RISK OF INJURY OR PROPERTY DAMAGE WHEN TRANSPORTING OR STORING WHAT CAN HAPPEN HOW TO PREVENT IT Fuel or oil can leak or spill and could If pressure washer is equipped with a fuel result in fire or breathing hazard, serious shut-off valve, turn the valve to the off injury or death can result. Fuel or oil leaks position before transporting to avoid fuel will damage carpet, paint or other leaks. If pressure washer is not equipped surfaces in vehicles or trailers. with a fuel shut-off va
Resumen del contenido incluido en la página 5
HAZARD RISK OF UNSAFE OPERATION WHAT CAN HAPPEN HOW TO PREVENT IT Unsafe operation of your pressure washer Do not use chlorine bleach or any other could lead to serious injury or death to corrosive compound. you or others. Become familiar with the operation and con- trols of the pressure washer. Keep operating area clear of all persons, pets, and obstacles. Do not operate the product when fatigued or under the influence of alcohol or drugs. Stay alert at all times. Never defeat the s
Resumen del contenido incluido en la página 6
HAZARD RISK OF INJURY FROM SPRAY WHAT CAN HAPPEN HOW TO PREVENT IT Always wear ANSI approved Z87 safety High velocity fluid spray can cause glasses.Wear protective clothing to protect objects to break, propelling particles at against accidental spraying. high speed. Never point wand at, or spray people or Light or unsecured objects can become animals. hazardous projectiles. Always secure trigger lock when wand is not in service to prevent accidental operation. Never permanently secur
Resumen del contenido incluido en la página 7
CARTON CONTENTS Accessories Panel English/ Spanish Engine Operation Manual Manual Bagged Accessories Panel Handle Engine Frame and Wheel Assembly Knobs Saddle Bolts Chemical Hose Nozzle Cleaning Kit High Pressure Hose Bagged Parts Multi-Adjustable Spray Wand Spray Gun Engine Oil 7- ENG D27935
Resumen del contenido incluido en la página 8
ASSEMBLY INSTRUCTIONS 1. Place handle assembly onto frame and connect handle to frame. NOTE: Knobs are assembled to inside of frame. 2. Connect wand to gun. Tighten securely. 3. Attach high pressure hose to gun. Tighten securely. 4. To Assemble Accessories Panel a. Remove top screws on handle assembly. b. Loosen bottom screws on handle assembly. Remove Loosen 8- ENG D27935
Resumen del contenido incluido en la página 9
c. Place grooves in accessories panel assembly onto screws and slide panel assembly into place. Screws d. Place screws (removed earlier) into the top holes and secure accessories panel assembly to handles. Do not overtighten. 5. Add engine oil (supplied) to engine. Refer to Engine Owners Manual supplied by engine manufacturer for correct procedure. NOTE: There will be a slight amount of oil in the engine from factory testing. 9- ENG D27935
Resumen del contenido incluido en la página 10
OPERATING INSTRUCTIONS READ THIS OPERATION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Chemical Hose Spray Gun High Pressure Hose Engine Multi- Adjustable Spray Wand High Pressure Pump BASIC ELEMENTS OF A PRESSURE WASHER High Pressure Pump (located inside the shroud): Increases the pressure of the water supply. Engine: Drives the h
Resumen del contenido incluido en la página 11
BASIC ELEMENTS OF ENGINE Refer to the engine manual for location and operation of engine controls. Choke Control: Opens and closes carburetor choke valve Throttle Control Lever: Controls engine speed. Starter Grip: Pulling starter grip operates recoil starter to crank engine. PRESSURE WASHER TERMINOLOGY PSI: Pounds per Square Inch. The unit of measure for water pressure. Also used for air pressure, hydraulic pressure, etc. GPM: Gallons Per Minute. The unit of measure for the flow rate of water
Resumen del contenido incluido en la página 12
HOW TO USE WAND: Your pressure washer is equipped with a multi-adjustable spray wand with both high and low pressure settings. The high pressure setting is for cleaning and rinsing, the low pressure setting is for applying chemicals or cleaning solutions to surfaces. When using the high pressure setting, DO NOT allow the jet- like spray to come in contact with unprotected skin, eyes, or with any pets or animals. Serious injury can occur. Risk of injection or injury to person. DO NOT direct disch
Resumen del contenido incluido en la página 13
HOW TO APPLY CHEMICALS AND CLEANING SOLVENTS Applying chemicals or cleaning solvents is a low pressure operation. NOTE: Use only soaps and chemicals designed for pressure washer use. Do not use bleach. To apply chemicals: 1. Press chemical hose onto barbed fitting located near high pressure hose connection of pump as shown. 2. Place other end of chemical hose with filter on it into container holding chemical/cleaning solution. NOTE: The chemical/water ratio is 7:1, for every 7 gallons of water
Resumen del contenido incluido en la página 14
STARTING Prior to starting, refer to your engine manual for proper starting procedures for your engine type. 1. In a well ventilated outdoor area add fresh high quality unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to engine manual for correct procedure. 2. Check engine oil level. See Engine Owners Manual for correct procedure. NOTE: There will be a slight amount of oil in the engine from factory testing. 3.
Resumen del contenido incluido en la página 15
MAINTENANCE When performing maintenance, you may be exposed to hot surfaces, water pressure, moving parts, or fire that can cause serious injury or death! Before performing any maintenance or repair, disconnect spark plug wire, let engine cool and release all water pressure. The engine contains flammable fuel. DO NOT smoke or work near open flames while performing maintenance. To ensure efficient operation and longer life of your pressure washer, a routine maintenance schedule should be prepared
Resumen del contenido incluido en la página 16
HOW TO CLEAN THE WATER INLET FILTER This screen filter should be checked periodically and cleaned if necessary. 1. Remove filter by grasping end and removing it from Filter Screen water inlet of pump as shown. 2. Clean filter by flushing it with water on both sides. 3. Re-insert filter into water inlet of pump. NOTE: Do not operate pressure washer without filter properly installed. 16- ENG D27935
Resumen del contenido incluido en la página 17
STORAGE ENGINE Consult the Engine Owners Manual for the manufacturer's recommendations for storage. PUMP It is recommended that you follow these steps to protect the internal seals of the pressure washer when STORING THE UNIT FOR MORE THAN 30 DAYS AND/OR WHEN FREEZING TEMPERATURES ARE EXPECTED. The manufacturer recommends using EXA80 Pump Saver/Winterizer. EXA80 Pump Saver/Winterizer may be purchased in stores where Excell pressure washers are sold. If EXA80 is not available, *RV antifreeze need
Resumen del contenido incluido en la página 18
TROUBLE SHOOTING GUIDE CAUSE PROBLEM CORRECTION No fuel. Add Fuel. Engine will not Pressure builds up after two pulls start (see Engine Squeeze gun trigger to relieve on the recoil starter or after initial pressure. Manual for further engine use. troubleshooting) Choke lever in the “No Choke” Move choke to the “Choke” position. position. Spark plug wire not attached. Attach spark plug wire. Choke lever in the “Choke” Move choke to the “No Choke” position on a “hot” engine or an position. engine
Resumen del contenido incluido en la página 19
CAUSE CORRECTION PROBLEM Wand not in low pressure. See How to Use Wand paragraph Will not draw in the Operation Section. chemicals Chemical filter clogged. Clean filter. Chemical screen not in chemical Insure end of chemical hose is fully submerged into chemical. Dilute chemical. Chemical should Chemical too thick. be the same consistency as water. Pressure hose is too long Lengthen water supply hose instead of pressure hose. Chemical build up in chemical Have parts cleaned or replaced injector.
Resumen del contenido incluido en la página 20
WARRANTY DeVilbiss Air Power Company warrants to the original purchaser who uses the product in a consumer application (personal, residential or household usage) that all products covered under this warranty are free from defects in material and workmanship for one year from the date of purchase. All products covered by this limited warranty which are used in commercial applications (i.e., income producing) are warranted to be free of defects in material and workmanship for 90 days from the date
