Resumen del contenido incluido en la página 1
on
SINGLE DISC GRINDER
Owner’s Manual
Parts List &
Operating Instructions
CAUTION
!
Read Safety
And General
Instructions
Carefully
Before Using
Saw For The
First Time.
serial number
You should record the serial number
of your stand on this owner’s manual
and on the warranty card, which must
WARNING
!
be sent in to be effective. Be sure
• Wear eye protection.
• Disconnect saw before servicing,
to include all pertinent information
when changing grinding wheels, and
cleaning.
required
Resumen del contenido incluido en la página 2
SAFETY INSTRUCTIONS FOR THE MK-SDG TILE SAW Congratulations on your purchase of a MK-SDG. We are certain that you will be pleased with your purchase. MK Diamond takes pride in producing the finest construction power tools and diamond blades in the industry. Operated correctly, your MK-SDG should provide you with years of service. In order to help you, we have included this manual. This owners manual contains information necessary to operate and maintain your MK- SDG safely and correctly.
Resumen del contenido incluido en la página 3
TABLE OF CONTENTS SAFETY Safety Messages ______________________________________________________ 4 Damage Prevention and Information Messages __________________________ 4 Safety Precautions ____________________________________________________ 4 California Proposition 65 Message ______________________________________ 6 Hazard Symbols ______________________________________________________ 7 Electrical Requirements and Grounding Instructions ______________________ 8 Single Disc Grinder Specific War
Resumen del contenido incluido en la página 4
SAFETY Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in injury or death to you or others. Failure to read and follow these instructions could also result in damage and/or reduced equipment life. SAFETY MESSAGES: Safety messages inform the user about potential hazards that could lead to injury, death and/or equipment damage. Each safety message will be preceded by one of the following (3) three words that ident
Resumen del contenido incluido en la página 5
on on on on on SAFETY MAKE THE WORKSHOP KID PROOF on Make the workshops kid proof by using padlocks, master switches or by removing starter keys. DO NOT FORCE THE TOOL A power tool will do a job better and safer operating at the rate for which it was designed. on USE THE RIGHT TOOL Do not force a tool or an attachment, to do a job that it was not designed to do. on USE THE PROPER EXTENSION CORD If using an extension cord make sure it is in good condition. When using an extension cord, be sure
Resumen del contenido incluido en la página 6
on on on on SAFETY on USE RECOMMENDED ACCESSORIES Consult the owner’s manual for recommended accessories. Using improper accessories may increase the risk of personal or by-stander injury. NEVER STAND ON THE TOOL Serious injury could occur if a power tool is tipped, or if a cutting tool is unintentionally contacted. CHECK FOR DAMAGED PARTS Before using a power tool, check for damaged parts. A guard or any other part that is damaged should be carefully checked to determine it would operate p
Resumen del contenido incluido en la página 7
on on on on SAFETY Hazard Symbols: Electrical Shock on on Never touch electrical wires or components while the engine is running. They can be sources of electrical shock which could cause severe injury or burns. Rotating Parts Keep hands, feet, hair, and clothing away from all moving parts to prevent injury. Never operate the saw with covers, shrouds, or guards removed. on Over Speed Never tamper with the governor components or settings to increase the maximum speed. Severe personal injury a
Resumen del contenido incluido en la página 8
SAFETY ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS: In order to prevent potential electrical shock and injury, the following electrical safety precautions and symbols should be followed at all times! WARNING ! In case of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged int
Resumen del contenido incluido en la página 9
SAFETY To avoid the possibility of the appliance plug or receptacle getting wet, position the saw to one side of a wall mounted receptacle. This will prevent water from dripping onto the receptacle or plug. A “drip loop,” shown in FIGURE 2, should be arranged by the user to properly position the power cord relative to the power source. The “drip loop” is that part of the cord below the level of the receptacle, or the connector, if an extension cord is used. This method of positioning the
Resumen del contenido incluido en la página 10
SAFETY SINGLE DISC GRINDER SPECIFIC WARNINGS: Wear eye protection. WARNING ! Replace damaged grinding blades before operating. SAFETY LABEL LOCATIONS Safety and warning labels are located according to the figure below. The labels contain important safety information. Please read the information contained on each safety label. These labels are considered a permanent part of your saw. If a label comes off or becomes hard to read, contact MK Diamond or your dealer for a replacement (B11) (G1
Resumen del contenido incluido en la página 11
SAFETY PRODUCT SPECIFICATIONS The MK-SDG is a versatile unit. Operated and used according to this manual, the MK-SDG will provide years of dependable service. Features • Uses either a 10 or 20 segment 10" diameter diamond grinding discs to level, smooth or clean the top surface of concrete slabs. (FIGURE 3) • Provides a smoother finish compared to other methods such as scarifiers or scabblers. • Two-position wheel carriage for grinding and easy transport. (FIGURE 4) • Front taper for enhanced
Resumen del contenido incluido en la página 12
UNPACKING and TRANSPORT UNPACKING CAUTION Use proper lifting techniques when lifting the MK-SDG ! If not already done, remove the MK-SDG, accessory box from the carton. CONTENTS In your container, you will find One (1) MK-SDG One (1) Grinding Discs One (1) MK-SDG Owners Manual One (1) Honda Owners Manual One (1) warranty card MK-SDG Grinding Owners Disc Manual Honda Owners Warranty Manual Card TRANSPORT: 1. The MK-SDG weighs approximately two hundred and thirty two (232) pounds; use care C
Resumen del contenido incluido en la página 13
ASSEMBLY and OPERATION ASSEMBLY: Follow the diagram below to prepare your MK-SDG for operation. Handlebar Adjustment Adjust the Handlebar, as shown on the Figure to the right, for ease of operation and comfort of the user. Grinding Discs Installation You need to install the grinding discs before operation of the MK-SDG The Figure to the left shows the components needed to install the discs. Surface finished with the MK-SDG-11 13 Revision 09/05, Effective Date September 30, 2005 MK-SDG
Resumen del contenido incluido en la página 14
ASSEMBLY and OPERATION (cont...) FOR GASOLINE ENGINE BEFORE STARTING 1. Use correct diamond wheel for grinding conditions. 2. Ensure wheel mountings are clean and bolts are tightened securely. 3. Check water jet for adequate flow. 4. Place grinding wheels on surface. 5. Start and warm up engine. 6. If application requires water, adjust water flow. 7. Adjust speed as required by application. DAILY MAINTENANCE 1. Check engine oil level. 2. Check and clean air filter. 3. Lubricate grease
Resumen del contenido incluido en la página 15
MAINTENANCE AND TROUBLESHOOTING 1. CLEAN UP Engine parts are extremely hot following use. Allow engine to cool 1/2 hour before cleaning. CAUTION ! Use care during cleanup to avoind injury. 1. To extend operating life, the MK-SDG should be cleaned following every use. NOTE: 2. Using a garden hose or pressure washer can force water into the air cleaner or muffler opening. 3. Use care when cleaning around electrical components. 2. FILLING FUEL TANK WARNING ! 1. Gasoline is highly flammable a
Resumen del contenido incluido en la página 16
MK-SDG EXPLODED VIEW EXPLODED VIEW WITH GAS ENGINE 16 Revision 09/05, Effective Date September 30, 2005 MK-SDG
Resumen del contenido incluido en la página 17
MK-SDG EXPLODED VIEW EXPLODED VIEW WITH ELECTRIC MOTOR 17 Revision 09/05, Effective Date September 30, 2005 MK-SDG
Resumen del contenido incluido en la página 18
MK-SDG EXPLODED VIEW 18 Revision 09/05, Effective Date September 30, 2005 MK-SDG
Resumen del contenido incluido en la página 19
MK-SDG PARTS LIST STAND PARTS LIST: Item Description Qty Part No. A Assembly, Accessory Pack A1 Grinding Wheels 10” (Reference only) 0 Reference A2 Pallet (not shown) 1 158259 A3 Carton, SDG-11 Grinder (not shown) 1 158272 A4 Tube, Owner’s Manual (not shown) 1 155419 A5 Manual, Owner’s (not shown) 1 158273 A6 Bolt, Hex HD, 3/8-24 x 1 Grinding Disk, Mounting 4 157803 A7 Washer, 3/8 Split Lock 4 150925 A8 Washer, 3/8 SAE Flat 4 150923 B Assembly, Frame B1 Frame Weldment 1 157780
Resumen del contenido incluido en la página 20
MK-SDG PARTS LIST (cont...) F3 Washer, Lock, Split 1/2 4 153524 F4 Washer, Flat SAE 1/2 4 150924 F5 Shaft, 1” Dia Large Gear 1 157302 F6 Flexible Mount, Morflex (Morse 402 Insert) 1 157411 F7 Mount, Grinding Wheel 1 157407 F8 Screw, Hex HD Cap 3/8-16 x 2 1/2 2 156030 F9 Screw, Flt. HD. Sc. 3/8-16 x 2 1/2 2 157562 F10 Nut, 3/8-16, Hex Nylock 4 152505 F11 Washer, 3/8 SAE Flat 4 150923 F12 Spacer, 1 ¼” OD, 1” I.D. x 1 3/8” 1 158257 F13 Key, Square, 1/4 x 1/4 x 1 1/2” 1 157560
