Resumen del contenido incluido en la página 1
Model Rotary Hammer
Modèle Marteau rotatif
DH 24PB2
Modelo Martillo perforador
INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS
WARNING
Improper and unsafe use of this power tool can result in death or serious bodily
injury!
This manual contains important information about product safety. Please read
and understand this manual before operating the power tool. Please keep this
manual available for others before they use the power tool.
MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE
AVERTISSEMENT
Une utilis
Resumen del contenido incluido en la página 2
CONTENTS English Page Page IMPORTANT SAFETY INFORMATION..... 3 ASSEMBLY AND OPERATION ............ 10 APPLICATIONS ................................. 10 MEANINGS OF SIGNAL WORDS ...... 3 PRIOR TO OPERATION ..................... 10 SAFETY ................................................... 4 HOW TO USE .................................... 12 HOW TO USE THE CORE BIT (FOR LIGHT LOAD) ... 15 GENERAL SAFETY RULES ................. 4 SPECIFIC SAFETY RULES AND SYMBOLS ..... 6 MAINTENANCE AND INSPECTION
Resumen del contenido incluido en la página 3
English IMPORTANT SAFETY INFORMATION Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures. Basic safety
Resumen del contenido incluido en la página 4
English SAFETY GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS 1. Work Area (1) Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. (2) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dus
Resumen del contenido incluido en la página 5
English (3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. (4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. (5) Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpect
Resumen del contenido incluido en la página 6
English SPECIFIC SAFETY RULES AND SYMBOLS 1. Hold tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. 2. ALWAYS wear ear protectors when using the tool for extended periods. Prolonged exposure to high intensity noise can cause hearing loss. 3. NEVER touch the tool bit with bare hands after operation. 4. NEVER wear glov
Resumen del contenido incluido en la página 7
English 14. Keep motor air vent clean. The tool’s motor air vent must be kept clean so that air can freely flow at all times. Check for dust build-up frequently.17. Never leave tool running unattended. Turn power off. 15. Operate power tools at the rated voltage. Operate the power tool at voltages specified on its nameplate. If using the power tool at a higher voltage than the rated voltage, it will result in abnormally fast motor revolution and may damage the unit and the motor may burn out. 16
Resumen del contenido incluido en la página 8
English DOUBLE INSULATION FOR SAFER OPERATION To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double insulation” means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by the operator. Therefore, either the symbol “ ” or the words “Double insulation” appear on the power tool or on the nameplate. Although this system has no exte
Resumen del contenido incluido en la página 9
English FUNCTIONAL DESCRIPTION NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safey instructions contained in this manual. Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool. NAME OF PARTS Nameplate Depth Gauge Drill Bit Housing Fro
Resumen del contenido incluido en la página 10
English ASSEMBLY AND OPERATION APPLICATIONS Rotation and hammering function Drilling anchor holes Drilling holes in concrete Drilling holes in tile Rotation only function Drilling in steel or wood (with optional accessories). Tightening machine screws, wood screws (with optional accessories). PRIOR TO OPERATION 1. Power source Ensure that the power source to be utilized conforms to the power source re- quirements specified on the product nameplate. 2. Power switch Ensure that the swit
Resumen del contenido incluido en la página 11
English 6. Mounting the drill bit (Fig. 2) Front cap Grip Part of SDS-plus shank CAUTION: To prevent accidents, make sure to turn the switch off and disconnect the plug from the receptacle. NOTE: Drill bit When using tools such as bull points, Fig. 2 drill bits, etc., make sure to use the genuine parts designated by our company. (1) Clean the shank portion of the drill bit. (2) Insert the drill bit in a twisting manner into the tool holder until it latches Grip itself. (Fig. 2) (3) Check the lat
Resumen del contenido incluido en la página 12
English CAUTION: The dust cup and dust collector (B) are for exclusive use of concrete drilling work. Do not use them for wood or metal drilling work. Insert dust collector (B) completely into the chuck part of the main unit. When turning the rotary hammer on while dust collector (B) is detached from a concrete surface, dust collector (B) will rotate together with the drill bit. Make sure to turn on the switch after pressing dust cup on the concrete surface. (When using dust collector (B)
Resumen del contenido incluido en la página 13
English 2. Rotation + Hammering Change Lever This rotary hammer can be set to rotation and hammering mode by pressing the push button and turning the change lever to mark. (Fig. 7) (1) Mount the drill bit. (2) Pull the trigger switch after applying the Push Button drill bit tip to the drilling position (Fig. 8) Fig. 7 (3) Pushing the rotary hammer forcibly is not necessary at all. Pushing slightly so that drill dust comes out gradually is just sufficient. Fig. 8 CAUTION: When the drill bit t
Resumen del contenido incluido en la página 14
English Drill bit may snap off while withdrawing the rotary hammer from the drilled hole. For withdrawing, it is important to use a pushing motion. Do not attempt to drill anchor holes or holes in concrete with the main unit in the rotation only function. Do not attempt to use the rotary hammer in the rotation and striking function with the drill chuck and chuck adaptor attached. This would seriously shorten the service life of every components of the machine. Bit 4. When driving machine s
Resumen del contenido incluido en la página 15
English Mounting Hole 6. Using depth gauge (Fig. 12) Depth Gauge (1) Loosen the knob on the side handle, and insert the depth gauge into the mounting hole on the side handle. (2) Adjust the depth gauge position ac- Knob on Side cording to the depth of the hole and Handle tighten the knob bolt securely. 7. How to use the drill bit (taper shank) Fig. 12 and the taper shank adaptor. (1) Mount the taper shank adaptor to the Grip Drill Bit rotary hammer. (Fig. 13) (2) Mount the drill bit (taper shank
Resumen del contenido incluido en la página 16
English (1) Mount the core bit to the core bit shank. (Fig. 15) Core Bit Lubricate the thread of the core bit Thread shank to facilitate disassembly. Core Bit Shank (2) Mount the core bit shank to the rotary hammer. (Fig. 16) (3)Insert the center pin into the guide plate Fig. 15 until it stops. (4) Engage the guide plate with the core bit, and turn the guide plate to left or right so that it does not fall even if it faces downward. (Fig. 17) 2. How to bore (Fig. 18) (1) Connect the plug to the p
Resumen del contenido incluido en la página 17
English MAINTENANCE AND INSPECTION WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection. 1. Inspecting the drill bits Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one or resharpening without delay when abrasion is noted. 2. Inspecting the screws Regularly inspect all screws and ensure that they are properly tightened. Should any of the screws be loosened, retighten
Resumen del contenido incluido en la página 18
English ACCESSORIES WARNING: ALWAYS use Only authorized HITACHI replacement parts and accessories. NEVER use replacement parts or accessories which are not intended for use with this tool. Contact HITACHI if you are not sure whether it is safe to use a particular replacement part or accessory with your tool. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage. NOTE: Accessories are subject to change without any obligation on the part of the H
Resumen del contenido incluido en la página 19
English Drill Bit (Taper shank) and taper shank adaptor (1) Drill Bit (Taper Shank) (2) Taper Shank Adaptor (SDS-plus shank) Cotter (Code No. 944477) External dia. Code No. Taper mode Code No. Applicable drill bit 7/16" 7/16" (11 mm) 944460 (11 mm) 1/2" (12.3 mm) Drill bit 1/2" 1/2" (12.7 mm) Morse taper 944461 303617 (Taper (12.3 mm) 9/16" (14.3 mm) (No. 1) shank) 1/2" 9/16" (14.5 mm) 993038 (12.7 mm) 11/16" (17.5 mm) 9/16" 944462 Drill bit (14.3 mm) Morse taper 303618 7/8" (21.5 mm) (Taper 9
Resumen del contenido incluido en la página 20
English 2. Knock-in anchor (Rotation + Hammering) Anchor Setter (for anchor setting) (SDS-plus shank) W 1/4" W 5/16" W 3/8" Anchor size (6.3 mm) (8 mm) (9.5 mm) 10-1/4" 10-1/4" 6-1/4" 10-1/4" Overall Length (260 mm) (260 mm) (160 mm) (260 mm) Code No. 302976 302975 303621 302974 W 1/4" W 5/16" W 3/8" Anchor size (6.3 mm) (8 mm) (9.5 mm) 10-1/4" 10-1/4" 6-1/4" 10-1/4" Overall Length (260 mm) (260 mm) (160 mm) (260
