Manual de instrucciones de Hunter Fan Hunter Ceiling Fan 22360

Resumen del contenido incluido en la página 1

®
SINCE 1 8 8 6
INSTALLATION INSTRUCTIONS FOR
®
HUNTER ORIGINAL CEILING FANS
®
Installing Your Hunter Ceiling
IMPORTANT!
Fan
READ AND SAVE THESE
Note To Installers: Please leave this manual with
INSTRUCTIONS!
the home owner.
Read this entire manual thoroughly before begin-
Tools needed:
ning installation.
• Pliers • 3/8” Socket Wrench
• Flat blade screwdriver • Phillips screwdriver
!WARNINGS!
• Electric drill • 11/64” drill bit
• To avoid possible electrical shock, before wi

Resumen del contenido incluido en la página 2

Step 2: Inspect the Fan 1. Unpack the fan carefully to avoid any damage to components. !CAUTION! • Never lift the motor by the wires. Let the motor rest in the carton liner for protection. 2. Check the sack parts. See Figure 2. (Not Drawn to Scale) Fan Parts Canopy Insert Hanger Bracket Assembly Canopy Pipe Nipple Blade Set Motor / Housing Assembly Oil Tube Figure 2 Blade Iron Set (Drawn to Scale) Hardware 1/4-10 Lag Screw Pull Chain Rubber Bushing / Pin Blade Assembly Screw Wire Nut Armature

Resumen del contenido incluido en la página 3

2. Drill two (2) 1/4” diameter holes 2-9/16” Step 3: Installation of Ceiling Mounting apart through the back of the outlet box into the Hardware cross brace. There may be two holes at the correct !CAUTION! spacing, but they will probably have to be enlarged. • Your Hunter ceiling fan weighs up to 50 lbs. The 3. Use the two (2) bracket screws to secure the following precautions must be taken for safety, hanger bracket and canopy plate to the joist as and to ensure that your fan is securely moun

Resumen del contenido incluido en la página 4

Step 5: Wiring Instructions Set Canopy NOTE: Before you do the final wiring, you should decide Screws Insert !WARNING! • To avoid possible electrical shock, before wir- ing fan, disconnect power by turning off the cir- cuit breakers both to the outlet box and to its associated wall switch location. If you cannot lock the circuit breakers in the “OFF” position, securely fasten a prominent warning device, such as a tag, to the service panel. Canopy how you want to control your fan - with a pull co

Resumen del contenido incluido en la página 5

Step 6: Lubrication Canopy Installation 1. Your fan has been shipped without oil in the 1. Lift the canopy off the neck of the motor. motor. A tube of high grade SAE 10 non-detergent 2. Slide the canopy and canopy insert up until oil is packed in the sack parts. All of the oil in the the three holes in the side of the canopy can be tube must be put into the fan. aligned with the three threaded holes in the canopy 2. Unscrew the oil hole screw on the side of plate. the switch housing. See Figu

Resumen del contenido incluido en la página 6

Grommet 7. Line up the other hole on the motor and fasten the second screw. NOTE: Before tightening the screws, make sure they are Fan not cross-threaded in the mounting holes. Blade 8. Tighten both screws securely. Repeat for the remaining blades. !CAUTION! • Do not attempt to run the fan until all screws have been tightened securely. 9. A blade balancing kit has been provided with your fan. Should the fan wobble in operation, Figure 13 you may use this kit to correct the balance per the NOTE

Resumen del contenido incluido en la página 7

Care and Maintenance Installation in Concrete Ceilings !CAUTION! !CAUTION! • Your Hunter ceiling fan weighs up to 50 lbs. The • Before performing any maintenance on the fan, following precautions must be taken for safety, disconnect the power to the fan. and to ensure that your fan is securely mounted to the ceiling. Lubrication Refer to Figure 18 for the steps below. Once properly installed, your fan needs little • For concrete mounting, the drilled hole must be attention, beyond checking the

Resumen del contenido incluido en la página 8

The Inside Story Oil is constantly pumped up the spiral groove to lubricate the rotor and the shaft. The oil is returned to the reservoir where the bearings are submerged in a bath of oil. This unique lubrication system is built into all ® Original Hunter Ceiling Fans. That’s one reason Hunters last so long, and why we can offer a Limited Lifetime Warranty. Should you move you fan to another location, it is a good idea to check the oil reservoir. Hunter ® has developed an accessory “Original