Resumen del contenido incluido en la página 1
Summerland Swing Set
Owner’s Manual and Assembly Instruction
Model #: 22-PS245 Model Name: Summerland Swing Set
Manual revision: 4/2006
Important: Keep this owner’s manual; do not discard in case you need to contact Pacific Cycle, Inc.
in the future. Should there be a change of ownership, please transfer this manual to the new owner to
ensure proper assembly and safety.
90 DAY LIMITED WARRANTY
Pacific Cycle, Inc. warrants this product to be free of defective mater
Resumen del contenido incluido en la página 2
To make claim under warranty, notification of such defect must be given to Pacific Cycle, Inc. By calling the phone number below, you will be instructed on how the product or part needing replacement should be shipped postpaid to Pacific Cycle, Inc. Customer Service and Assistance 1-800-242-6110 Monday – Friday 8am-5pm CST Please contact the Playsafe™ customer service team if you have any questions about our product, need assembly assistance or need replacement parts for the swing s
Resumen del contenido incluido en la página 3
• EQUIPMENT MAY BE SLIPPERY WHEN WET. DO NOT ALLOW CHILDREN TO USE THE EQUIPMENT WHEN WET. • PARENTS SHOULD REGULARLY CHECK OPENINGS AND SURFACES, SUCH AS SLIDES, FOR ITEMS THAT MAY BE HAZARDOUS. ARENTS SHOULD CHECK SWING CHAINS TO INSURE THEY ARE SECURE AND CAN NOT BE LOOPED • P BACK ON THEMSELVES. • DO NOT PLACE ANY PART OF THE BODY NEAR MOVING PARTS ON GLIDE RIDES OR TOP BRACKETS. • NEVER SLIDE HEAD FIRST DOWN THE SLIDE. • VERIFY THAT ALL SWINGS AND CHAINS ARE SECURED AT BOTH ENDS.
Resumen del contenido incluido en la página 4
FALL HEIGHT IN FEET FROM WHICH A LIFE THREATENING INJULY WOULD NOT BE EXPECTED Material Type 6 in. depth 9 in. 12 in. Double Shredded Bark Mulch 6’ 10’ 11’ Wood Chips 6’ 7’ 12’ Fine Sand 5’ 5’ 9’ Fine Gravel 6’ 7’ 10’ It is recommended that a shock absorbing material should extend a minimum of 6’ in all directions from the perimeter of the stationary equipment such as climbers and slides. However, because children may deliberately jump from a moving swing, t
Resumen del contenido incluido en la página 5
PARTS LIST FOR SWING SET Main Frame Name Each Swings and Trapeze Top Bar with Corner Fittings Name Each and Hooks 2 Swing Seat with Chains 3 Leg 6 Trapeze 1 Support Bar 3 Slide Name Each Glider Name Each Rail/Ladder Leg 2 Glider Pole (vertical) with Foot Rests 2 Front Leg 1 Glider Pole (horizontal) with Seats 2 Slide 1 Glider Frame Attachment 1 Ladder Step 2 PRE-ASSEMBLED HARDWARE For easier assembly, Playsaf
Resumen del contenido incluido en la página 6
Pre-Assembled Parts: • Corner fittings should be attached to the top bar. • Swing hooks should be in place on the top bar. • Hardware for the legs should be in place in the corner fitting prongs. • Hardware for the support bars should be in place on the legs. Step Illustration Instructions Hardware Reference 1 Remove the hardware from the prong of a Part Ref. #: PSHW10 corner fitting in order to insert one of the legs. 2 Align the two sets of holes and replace the Part Ref. #:
Resumen del contenido incluido en la página 7
NOTE: One support bar has holes for the slide attachment. The holes should be positioned toward the front of the swing set. GLIDER ASSEMBLY Required Parts: Vertical Poles x2 (Footrests attached) Horizontal Poles x2 (Seats attached) Glider attachment x1 Pre-Assembled Parts: • The seats should be attached to the horizontal poles. These must be disassembled to complete the steps below. • The foot rests should be attached to the vertical poles. Step Illustration
Resumen del contenido incluido en la página 8
NOTE: The curved portion of the pole is the top and it should face the inside of the swing frame. 3 Connect the two horizontal poles (must Part Ref. #: PSHW15, PSHW11 first be disassembled from the seats) to the two vertical poles using the hardware provided. Be sure that the plastic bushings are between the vertical poles and horizontal poles. 4 Reattach the seats onto the horizontal poles Part Ref. #: PSHW1 using the flat headed screw, washer, and lock nut.
Resumen del contenido incluido en la página 9
2 Check the lock nut and bolt on the swing seat to Part Ref. #: PSSH11, PSHW13 make sure that they are secure. SLIDE ASSEMBLY Required Parts: Slide x1 Rail/Ladder Leg x2 Front Leg x1 Ladder Step x2 Link Bar x2 Proper Placement: Slide Assembly Correct Location Incorrect Location Pre-Assembled Parts: • The screws and bolts for the slide rail/ladder legs are inserted on the slide. They will need to be removed p
Resumen del contenido incluido en la página 10
2 Insert the rail/ladder legs through the holes in the top of the slide. Align the ladder holes with the slide holes. 3 Insert the screws through the holes in the back of Part Ref. #: PSHW24 the slide and secure them to the hand rails with the screws and locking nuts provided. 4 Locate the slide front leg and insert it into the front Part Ref. #: PSHW24 outside hand rail tube, on the underside of the slide. Place a screw in that hole and secure it with the lock nut
Resumen del contenido incluido en la página 11
IMPORTANT LAST STEPS! TIGHTEN ALL HARDWARE. Do not allow children to play on the swing set until it is fully assembled, all items are tightened, and the unit is properly anchored. • Do not over tighten nuts and bolts. Once they are tight, turn them ½ rotation more to be sure they are secure. • Check all parts on all rides before allowing a child on the swing set. • Be sure to check and tighten the hardware on a regular basis to ensure the safety of the users. Your Playsafe™ Summerl
