Manual de instrucciones de Poulan 96192002901

Manual de instrucciones del aparato Poulan 96192002901

Aparato: Poulan 96192002901
Categoría: Quitanieves
Fabricante: Poulan
Tamaño: 1.47 MB
Fecha de añadido: 2/28/2014
Número de páginas: 40
Imprimir el manual

Descargar

¿Cómo se utiliza?

Nuestro propósito es proporcionarte el acceso más rápido posible a los contenidos incluidos en los manuales de instrucciones del aparato Poulan 96192002901. Utilizando la vista previa online, puedes ver rápidamente el índice de contenidos y pasar a la página donde encontrarás la solución a tu problema con Poulan 96192002901.

Para tu comodidad

Si ver los manuales de instrucción de Poulan 96192002901 directamente en esta página no es cómodo para ti, puedes utilizar dos soluciones posibles:

  • Vista en pantalla completa – Para ver cómodamente los manuales de instrucciones (sin descargarlos en tu ordenador) puedes utilizar el modo de vista en pantalla completa. Para activar la vista del manual Poulan 96192002901 en pantalla completa, utiliza el botón Pantalla completa
  • Descargar al ordenador – también puedes descargar el manual de instrucciones de Poulan 96192002901 a tu ordenador y guardarlo en tu colección. Sin embargo, si no quieres ocupar espacio en tu dispositivo, siempre podrás descargarlo de ManualsBase.
Poulan 96192002901 Manual de instrucciones - Online PDF
Advertisement
« Page 1 of 40 »
Advertisement
Versión impresa

Muchas personas prefieren no leer el documento en la pantalla, sino en versión impresa. La opción de impresión también está prevista y puedes utilizarla haciendo clic en el enlace más arriba - Imprimir el manual. No tienes que imprimir el manual completo de Poulan 96192002901, solo las páginas que elijas. Ahorra papel.

Resúmenes

A continuación encontrarás resúmenes de los contenidos incluidos en las páginas posteriores del manual de instrucciones para Poulan 96192002901. Puedes utilizarlos si quieres ver rápidamente el contenido que se encuentra en la siguientes páginas del manual.

Resúmenes de contenidos
Resumen del contenido incluido en la página 1

IMPORTANT MANUAL Do Not Throw Away
OWNER'S MANUAL
MODEL NUMBER:
WARNING:
Read the Owner's Manual and
fol low all Warnings and Safety
PR624ES
In struc tions. Fail ure to do so
can result in serious injury.
SNOW THROWER
428689 Rev. 2 09.23.09 AP
Always Wear Eye Protection During Operation
Printed in the U.S.A.

Resumen del contenido incluido en la página 2

IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Snow throwers have ex- Look for this symbol to point out im- posed rotating parts, which can cause por tant safety precautions. It means severe injury from contact, or from ma- CAUTION!!! BE COME ALERT!!! YOUR terial thrown from the discharge chute. SA

Resumen del contenido incluido en la página 3

6. When cleaning, repairing or inspecting the snow thrower, 16. Never touch a hot engine or muffler. stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect Clearing a Clogged Discharge Chute the spark plug wire and keep the wire away from the Hand contact with the rotating impeller inside the discharge plug to prevent someone from accidentally starting the chute is the most common cause of injury associated with engine. snow throwers. Never u

Resumen del contenido incluido en la página 4

PARTS PACKED SEPARATELY IN CARTON (1) AUGER CONTROL ROD (1) MULTI- WRENCH (180684) (3) RETAINER SPRINGS (2) FLAT WASHERS (169675) (1) POWER CORD (198563) (1) DISCHARGE CHUTE ROTATOR HEAD MOUNTING (2) CARRIAGE BOLTS 3/8-16 x 2.25 (2) SAFTEY IGNITION KEY (422663) (1) WASHER 3/8 (1) LOCKNUT 3/8 (19131316) (73800600) (2) HANDLE KNOBS EXTRA SHEAR BOLTS AND NUTS (2) SHEAR BOLTS 1/4-20 x 1-3/4 (2) LOCKNUTS (192090) 1/4-20 (73800400) ASSEMBLY / PRE-OPERATION Read these instructions and this manual in

Resumen del contenido incluido en la página 5

ASSEMBLY / PRE-OPERATION NOTE: The multi-wrench may be used for assembly of the INSTALL TRACTION DRIVE CONTROL ROD chute rotator head to snow thrower and making ad just ments (See Figs. 3 and 4) to the skid plates. The traction drive control rod is installed on the snow UNFOLD UPPER HANDLE thrower. 1. Raise upper handle to the operating position and 1. Remove plastic tie securring rod to lower handle. tight en handle knobs securely. Additional carriage 2. With top end of rod positioned und

Resumen del contenido incluido en la página 6

ASSEMBLY / PRE-OPERATION INSTALL DISCHARGE CHUTE / CHUTE ROTATOR INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) HEAD (See Fig. 7) 1. Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. NOTE: The multi-wrench provided in your parts bag may Slide straight rod end through the small hole in the be used to install the chute rotator head. vinyl sleeve. Hook spring in hole in rod end. 1. Place discharge chute assembly on top of chute base

Resumen del contenido incluido en la página 7

OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFOR

Resumen del contenido incluido en la página 8

OPERATION DISCHARGE CHUTE MUF FLER ELECTRIC CONTROL LEVER AUGER START DRIVE CONTROL SPEED BUTTON TRACTION DRIVE LEVER GAS O LINE CON TROL CONTROL LEVER FILLER CAP LEVER POWER CORD PLUG CHOKE CHUTE CON- DE FLEC TOR TROL SAFETY IGNITION KEY ON / OFF SWITCH CHUTE PRIM ER DISCHARGE DE FLEC TOR CHUTE KNOB FUEL SHUT-OFF VALVE RECOIL (AUXILIARY) STARTER HANDLE HANDLE CLEAN-OUT TOOL KNOB MUF FLER NOTE: ITEMS ABOVE ARE SHOWN IN THEIR TYPICAL TOOLBOX LOCATION ON THE ENGINE. ACTUAL LO

Resumen del contenido incluido en la página 9

OPERATION The operation of any snow thrower can result TO CONTROL SNOW DISCHARGE (See Figs. 11 & 12) in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear WARNING: Snow throwers have ex- safety glasses or eye shields while operating posed rotating parts, which can cause 00155 your snow thrower or performing any ad just- severe injury from contact, or from ma- ments or repairs. W e recommend standard safe ty glasses terial thrown from the discharge ch

Resumen del contenido incluido en la página 10

OPERATION TO THROW SNOW (See Fig. 13) • Make sure the discharge chute is pointed in a safe direc- tion (no vehicles, buildings, people, or other objects are The auger rotation is controlled by the auger control lever in the direction of discharge) before restarting the engine. located on the right side handle. • Restart the engine, then squeeze the auger control • Squeeze auger control lever to handle to engage the lever to the handle to clear snow from the auger hous- auger and throw snow.

Resumen del contenido incluido en la página 11

OPERATION TO ADJUST SKID PLATES (See Fig. 16) ADD GASOLINE (See Fig. 17) NOTE: The wrench provided in your parts bag may be • Fill fuel tank to bottom of tank filler neck. Do not over- used to adjust the skid plates. fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Skid plates are located on each side of the auger housing Purchase fuel in quan ti ties that can be used within 30 and adjust the clearance between the scraper bar a

Resumen del contenido incluido en la página 12

OPERATION TO START ENGINE 5. Pull recoil starter handle quickly. Do not allow starter rope to snap back. • Be sure fuel shut-off valve is in the “OPEN” position. 6. When the engine starts, release the recoil starter han dle Your snow thrower engine is equipped with both a 120 Volt and slowly move the choke control to the “OFF” posi- A.C. electric starter and a recoil starter. The electric starter tion. is equipped with a three-wire power cord and plug and is designed to operate on 120 Vol

Resumen del contenido incluido en la página 13

MAINTENANCE GENERAL REC OM MEN DA TIONS LUBRICATION CHART The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. SAE 5W-30 Motor Oil To receive full value from the warranty, operator must maintain snow thrower as in struct ed in this manual. Some See “ENGINE” ad just ments will need to be made periodically to properly maintain your snow thrower. All adjustments in the Service in Maintenance and Ad just ments section of this ma

Resumen del contenido incluido en la página 14

MAINTENANCE AUGER GEAR CASE 1. Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come • The gear case was filled with lubricant to the proper in contact with plug. level at the factory. The only time the lubricant needs attention is if service has been performed on the gear 2. Clean area around drain plug. case. 3. Remove drain plug and drain oil in a suitable container. • If lubricant is required, use only Ronex ED #1 4. Install drain p

Resumen del contenido incluido en la página 15

SERVICE AND ADJUSTMENTS IMPELLER SHEAR BOLTS WARNING: To avoid serious injury, before The impeller is secured to the impeller shaft with two (2) performing any service or ad just ments: capscrew/shear bolts and hex nuts. Should a foreign object 1. Be sure the on/off switch is in the or ice become lodged in the impeller, the capscrews are OFF position. de signed to break, preventing damage to any other com- po nents. If impeller does not turn when auger control lever 2. Remove safety igniti

Resumen del contenido incluido en la página 16

SERVICE AND ADJUSTMENTS TO REPLACE BELTS (See Fig. 20) 8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around The auger and traction drive belts are not adjustable. If pulleys. the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be HINT: Insert a 3/8" drive ratchet (in the “ON” position) into replaced by a service center/department. the square hole in idler arm and rotate ratchet clockwise to rel

Resumen del contenido incluido en la página 17

SERVICE AND ADJUSTMENTS TO REMOVE WHEELS (See Fig. 21) ENGINE • Remove the klik pin and remove wheel from axle. See engine manual. IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To dis en gage CARBURETOR drive system from the wheels (for pushing or trans port ing Your carburetor is not adjustable. Engine performance the snow thrower), remove klik pin from wheel hub and should not be affected at altitudes up to 7,000 feet (2,134 insert

Resumen del contenido incluido en la página 18

STORAGE Immediately prepare your unit for storage at the end of the NOTE: Fuel stabilizer is an acceptable alternative in min- season or if the unit will not be used for 30 days or more. i miz ing the formation of fuel gum deposits during stor age. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. WARNING: Never store the snow Run engine at least 10 min utes after adding stabilizer to thrower with gaso line in the tank

Resumen del contenido incluido en la página 19

TROUBLESHOOTING See appropriate section in manual unless directed to an authorized service center/department. PROBLEM CAUSE CORRECTION Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key. is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline. 4. Throttle in STOP position 4. Move throttle to FAST position (or ON/OFF switch is OFF). (or ON/OFF

Resumen del contenido incluido en la página 20

REPAIR PARTS SNOW THROWER - - MODEL NO. PR624ES (96192002901) AUGER HOUSING / IMPELLER ASSEMBLY 1 KEY PART NO. NO. DESCRIPTION 1 404928X428 AUGER HOUSING 2 404931X429 SCRAPER BAR 3 72270505 CARRIAGE BOLT 5/16 −18 X .625 4 155377 NUT 5/16 −18 3 (5x) 4 (5x) 2 01.07.001-A 2 3 1 1 2 KEY PART NO. NO. DESCRIPTION 1 420478 AUGER BEARING 3 2 411939 BEARING PLUG 3 179582 SCREW 5/16 −18 X 1.00 01.07.024-B NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPO


Manuales de instrucciones similares
# Manual de instrucciones Categoría Descargar
1 Poulan 183615 Manual de instrucciones Quitanieves 0
2 Poulan 185143 Manual de instrucciones Quitanieves 0
3 Poulan 185156 Manual de instrucciones Quitanieves 0
4 Poulan 187879 Manual de instrucciones Quitanieves 0
5 Poulan 185136 Manual de instrucciones Quitanieves 0
6 Poulan 183618 Manual de instrucciones Quitanieves 0
7 Poulan 187881 Manual de instrucciones Quitanieves 0
8 Poulan 187877 Manual de instrucciones Quitanieves 0
9 Poulan 187883 Manual de instrucciones Quitanieves 0
10 Poulan 188047 Manual de instrucciones Quitanieves 0
11 Poulan 183616 Manual de instrucciones Quitanieves 0
12 Poulan 187887 Manual de instrucciones Quitanieves 0
13 Poulan 189539 Manual de instrucciones Quitanieves 0
14 Poulan 189645 Manual de instrucciones Quitanieves 0
15 Poulan 192034 Manual de instrucciones Quitanieves 0
16 Agri-Fab 45-0402 Manual de instrucciones Quitanieves 2
17 Agri-Fab 45-0418 ATV Manual de instrucciones Quitanieves 1
18 Agri-Fab 45-0418 Manual de instrucciones Quitanieves 1
19 Alliance Laundry Systems DRYING TUMBLERS 70269501R3 Manual de instrucciones Quitanieves 2
20 Ariens 924 SNO-THRO 924109 Manual de instrucciones Quitanieves 60