Resumen del contenido incluido en la página 1
Assembly and Owner’s Manual
Gas Smoker
2505G 3005G
3405G 3405GT
3405GW 3605G
3405BG 3405BGW
ASSEMBLER / INSTALLER:
Leave these instructions with the consumer.
CONSUMER / USER:
Read all of these instructions and keep them in a safe place for future reference.
DANGER WARNING
If you smell gas: 1. Do not store spare LP cylinder within 10 feet (3.05 m)
1. Shut off gas to the appliance. of this appliance.
2. Extinguish any open flames. 2. Do not store or use gasoline or other flammable
3. Open door. l
Resumen del contenido incluido en la página 2
Statement of Commitment Congratulations and thank you for your purchase of your new Great Outdoors grill. We are pleased that you have recognized the value of the design, function, and quality of components used in this product. We believe it is among the nest on the market. We are committed to producing quality products that your family will enjoy for years to come. If or any reason we have failed to meet or exceed your expectations, please allow us the opportunity to make it right by calling
Resumen del contenido incluido en la página 3
READ ALL INSTRUCTIONS AND WARNINGS! YOUR SAFETY IS VERY IMPORTANT - FAILURE TO FOLLOW PROPER PROCEDURES AND SAFEGUARDS MAY RESULT IN SERIOUS PERSONAL INJURY OR PROPERTY DAMAGE. DO NOT use this smoker in a manner other than its intended purpose. It is NOT intended for commercial use. It is NOT intended to be installed or used in or on a recreational vehicle and/or boats. The smoker is not to be used as a heater. Keep a fire extinguisher accessible at all times. The use of alcohol, prescription or
Resumen del contenido incluido en la página 4
Use caution when opening the door of the smoker while in operation. Keep hands, face, and body safe from hot steam or flare-ups. Protect your nose and mouth from smoke inhalation. DO NOT wear loose clothing while operating the smoker. Tie back long hair while operating the smoker. ALWAYS wear fully-covering shoes while operating the smoker. Allow the smoker and its components to cool completely before conducting any routine cleaning or maintenance. NEVER use glassware, plastic, or ceramic cookwa
Resumen del contenido incluido en la página 5
Assembly Step 1 - Identifying the parts Check your package contents for these parts. If you are missing any parts, or if any parts are damaged, please call our toll-free customer service line to order parts. DO NOTRETURNYOUR SMOKERTOTHE RETAILER - CALLUS FIRST! 1-800-668-5323 See next page for part index and part numbers 5 6 4 1 2 3 9 8 10 12 7 13 11 14 5
Resumen del contenido incluido en la página 6
Assembly Step 1 - Continued Check your package contents for these parts. If you are missing any parts, or if any parts are damaged, please call our toll-free customer service line to order parts. DO NOTRETURNYOUR SMOKERTOTHE RETAILER - CALLUS FIRST! 1-800-668-5323 PartNumber by Model Item Qty Description No. 2505G 3005G 3405G 3405GT 3405GW 3605G 3405BG 3405BGW 1 1 CabinetAssembly AZ002001 AZ002018 AZ002026 AZ002026 AZ002026 AZ002034 AZ002040 AZ002040 1a 1 Cabinet AZ002002 AZ002019 AZ002027 AZ002
Resumen del contenido incluido en la página 7
Assembly Step 2 Locate these parts: Tools needed: 4 Legs Cabinet Assembly Phillips Head Screwdriver HARDWARE BAG Hardware: A 1/4-20 x 5/8” Bolts 16 Required 1. Set the cabinet assembly top side down. 2. For each leg, line up the holes and insert the bolts. Nuts are pre-welded to the cabinet. IMPORTANT: One leg contains an extra hole on its side and must be Leg with extra hole mounted at the front in the position shown. This hole will later be used to secure the gas hose to the leg with a zip-tie
Resumen del contenido incluido en la página 8
Assembly Step 3 Locate these parts: Tools needed: Control Panel Assembly Phillips Head Screwdriver HARDWARE BAG Hardware: A 1/4-20 x 5/8” Bolts (2 Remaining from previous step) 1. Place the Control Panel Assembly between the front legs as shown. There are slots on the control panel that fit around the legs. The mounting tabs fit to the inside of the legs and line up with the bolt holes. 2. Be sure all the tabs on the back side of the control panel are captured around the legs as shown below. 3.
Resumen del contenido incluido en la página 9
Assembly Step 4 Locate these parts: Tools needed: Burner Assembly Phillips Head Screwdriver HARDWARE BAG Hardware: B 1/4-20 x 1/2” Bolts 3 Required 1. Set the burner assembly onto the cabinet as shown. IMPORTANT: The burner tube must slide properly onto the valve stem as shown below. 2. Secure the burner assembly with the three bolts from the inside of the cabinet. Securely tighten the bolts. 3. Attach the loose igniter wire to the igniter on the control panel as shown below. 9
Resumen del contenido incluido en la página 10
Assembly Step 5 Locate these parts: Tools needed: Damper Plate Phillips Head Screwdriver HARDWARE BAG Hardware: C 3/8” 10-24 Nut 10-24 Lock Washer 10-24 x 5/8” Bolt Wrench 1 Required 1 Required 1 Required 1. Turn the smoker upright. 2. Set the damper plate on top of the cabinet and line it up with the corresponding “butterfly” holes. One Bolt of the tabs will seat inside one of the holes. 3. Insert a bolt from the top through the Damper center hole. 4. From the bottom side, place a lock washer a
Resumen del contenido incluido en la página 11
Assembly Step 6 Locate these parts: Tools needed: Phillips Head 2 Carry Screwdriver Handles HARDWARE BAG Hardware: D 7/16” 1/4-20 Nuts 1/4 Lock Washers 1/4-20 x 5/8” Bolts Wrench 8 Required 8 Required 8 Required 1. Line up the carry handle with the corresponding holes on the side of the cabinet as shown. The handles must be positioned upright with the bolt holes on the bottom as shown. 2. Insert the bolts from the outside and thread the lock washers and nuts from the inside of the cabinet. 3. Fi
Resumen del contenido incluido en la página 12
Assembly Step 7 Locate these parts: Wood Box Wood Chip Box Rack and Lid No tools or hardware are required for this step. 1. Insert the wood box rack into the bottom of the smoker. The feet of the rack sit in the four indentions in the bottom. 2. Set the wood chip box onto the rack. Make sure it is seated properly and securely in the center of the rack. 3. Place the lid on the wood chip box. 12
Resumen del contenido incluido en la página 13
Assembly Step 8 Locate these parts: Cooking Grids Water Pan No tools or hardware are required for this step. 1. Slide the water pan into the bottom rack position as shown. 2. Insert the cooking grids into any of the remaining rack positions as desired. For best access, the grid wires should run front to back as shown. 13
Resumen del contenido incluido en la página 14
Assembly Step 9 HARDWARE BAG Locate these parts: Door Handle Kit Tools needed: E Mounting Bracket 1/4-20 x 3/8” Bolts Phillips Head and 1/4-20 Lock Handle Spring Screwdriver Washers (2 ea) Handle Washer 1. Slide the handle washer onto the end of the door handle, followed by the handle spring as shown. 1 2. Feed the door handle into the hole through the front of the door panel. 3. From the back side of the door panel, insert the mounting bracket over the end of the handle as shown. 4. With lock w
Resumen del contenido incluido en la página 15
Assembly Step 10 HARDWARE BAG Locate these parts: F 2 Push Nuts Nameplate with Heat Indicator No tools are required for this step. 1. Insert the name plate mounts and heat indicator prong through the mounting holes in the front of the door panel. 2. From the inside of the door panel, securely attach the push nuts to the name plate mounts. 15
Resumen del contenido incluido en la página 16
Assembly Step 11 HARDWARE BAG Locate these parts: G Tools needed: S-Hook Pliers Zip Tie Using the zip tie, secure the hose to the front leg as shown. Do not pull the zip tie tight - leave it just loose enough so that the hose can be adjusted if needed. Tying the hose to the leg helps prevent the hose from coming into contact with the hot burner chamber. Inspect the installation underneath the smoker to ensure that the hose is not rubbing any portion of the burner chamber. 1. Place one end of the
Resumen del contenido incluido en la página 17
Connecting the LP Tank ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED TO PREVENT FIRE, DAMAGE, AND / OR INJURY. 1. The knob on the LP tank must be closed. See that the knob is turned clockwise to a full stop. 2. Check that the control knob on the smoker is turned off. 3. Remove the protective cap from the LP tank valve and coupling nut, if present. 4. Hold the regulator in one hand and insert the nipple into the valve outlet. Be sure the nipple is centered in the valve outlet. The
Resumen del contenido incluido en la página 18
Connecting the LP Tank - Continued ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED TO PREVENT FIRE, DAMAGE, AND / OR INJURY. Cylinders must be filled before initial use. All handling, transport, filling and storage of LP gas cylinders must be in accordance with NFPA 58 Storage and Handling of Liquid Petroleum Gases, or CSAB 149.1 Natural Gas and Propane Installation Code. Cylinders must be suitably tied down during transport. Do not place any other items on top of cylinders at any
Resumen del contenido incluido en la página 19
Operating Instructions Pre-Use Procedures Your smoker has been packaged with a retail store level point-of-purchase label that hangs on the front of the door panel. This label must be removed before use. To remove the label, simply cut or tear along the indicated line and pull the top portion of the label from behind the name plate. Before you cook food in your smoker, it is important to “season” your smoker. Seasoning seals the paint and interior of your smoker to enhance flavoring, durabi
Resumen del contenido incluido en la página 20
Adding Wood / Charcoal To add wood chips before cooking, simply fill the wood chip box with your choice of flavoring hardwood chips. The amount and type of wood you use is entirely up to you. One full box is typically enough for several hours of smoking. Once the box is filled, place the lid on top of the box and set the box in the smoker. To add wood chips while cooking, we recommend using tongs or long handled pliers to remove the box lid and to place the pieces into the wood chip
