Resumen del contenido incluido en la página 1
Model No. 831.14622.0
Serial No.
Write the serial number in the
WEIGHT SYSTEM EXERCISER
space above for future reference.
User’s Manual
Serial Number Decal (under seat)
• Assembly
• Adjustments
• Troubleshooting
• Part List and Drawing
CAUTION
Read all precautions and instruc-
tions in this manual before
using this equipment. Save this
Sears, Roebuck and Co., Hoffman Estates, IL 60179
manual for future reference.
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ASSEMBLY . . . . . .
Resumen del contenido incluido en la página 3
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight system. 1. Read all instructions in this manual and all 10. The weight system is designed to be used warnings on the weight system before using only with the included weight. Do not use the the weight system. Use the weight system weight system with dumbbells or any other only as described in this manual. type of weight to increase the resistance. 2. It is the re
Resumen del contenido incluido en la página 4
BEFORE YOU BEGIN ™ Thank you for selecting the versatile WEIDER PRO reading this manual, please see the front cover of this 4300 weight system. The weight system offers a selec- manual. To help us assist you, note the product model tion of weight stations designed to develop every major number and serial number before contacting us. The muscle group of the body. Whether your goal is to tone model number is 831.14622.0. The serial number can your body, build dramatic muscle size and strength, or
Resumen del contenido incluido en la página 5
PART IDENTIFICATION CHART—Model No. 831.14622.0 R1006A Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw- ing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached. If a part is missing, call toll-free 1-877-992-5999. O M6 Nylon M8 Nylon M10 Nylon M12 Nut (112) Locknut (107) Locknut (78
Resumen del contenido incluido en la página 6
PART IDENTIFICATION CHART—Model No. 831.14622.0 R1006A M8 x 69mm Shoulder Bolt (87) M8 x 75mm Carriage Bolt (83) M10 x 65mm Bolt (85) M10 x 75mm Bolt (82) M8 x 80mm Bolt (100) M8 x 65mm Bolt (101) M10 x 65mm Button Bolt (106) M10 x 80mm Bolt (84) M6 x 60mm Button Screw (91) M10 x 82mm Button Screw (92) M10 x 60mm Bolt (79) M10 x 85mm Bolt (81) M10 x 50mm Bolt (97) M10 x 61mm Bolt Set (116) M10 x 45mm Bolt (86) M10 x 110mm Bolt (93) M6 x 32mm Screw (89) M6 x 28mm M10 x 120mm Bolt (115) Bolt (94)
Resumen del contenido incluido en la página 7
PART IDENTIFICATION CHART—Model No. 831.14622.0 R1006A Backrest Adjustment Knob (53) Curl Adjustment Knob (58) Seat Adjustment Knob (52) 7
Resumen del contenido incluido en la página 8
ASSEMBLY Make sure you have the following tools: Make Assembly Easier for Yourself • Two adjustable wrenches Everything in this manual is designed to • One standard screwdriver ensure that the weight system can be assem- bled successfully by anyone. Before begin- • One phillips screwdriver ning assembly, make sure to read the information on this page. This brief intro- • One rubber mallet duction will save you much more time than • You will also need grease or petroleum jelly, a it takes to read
Resumen del contenido incluido en la página 9
1 Frame Assembly 1. Before beginning assembly, make sure you understand the information in the box on page 8. See the PART IDENTIFICATION CHARTS on pages 5 and 6 of this manual 1 83 for help identifying small parts. Insert four M8 x 75mm Carriage Bolts (83) up 83 through the Base (1). Note: It may be helpful to place a piece of tape over each Bolt head to hold it in place. 2 2. Insert an M8 x 75mm Carriage Bolt (83) up through the Stabilizer (3). Attach the Base (1) and the two Weight Guides (18
Resumen del contenido incluido en la página 10
4. Attach the Frame (9) to the Upright (2) with two 4 M8 x 80mm Bolts (100), two M8 Washers (103), 2 78 and two M8 Nylon Locknuts (78). Do not tighten 9 100 the Nylon Locknuts yet. 78 103 78 Attach the Frame (9) to the Front Leg (10) with two M8 x 65mm Bolts (101), two M8 Washers 78 (103), and two M8 Nylon Locknuts (78). Do not 100 103 tighten the Nylon Locknuts yet. 103 10 101 5. Attach the Top Frame (4) to the Upright (2) with 5 two M8 x 80mm Bolts (100), two M8 Washers (103), and two M8 Nylon
Resumen del contenido incluido en la página 11
7. Attach a Shroud Cover (23) to the Left and Right 7 114 Shrouds (21, 22) with two M6 x 28mm Bolts (94), 94 107 four M6 Washers (114), and two M6 Nylon 114 114 Locknuts (107). 23 114 94 Attach the Shroud Cover (23) to the Top Frame (4) with four M4 x 16mm Self-tapping Screws 110 110 (110) and four M4 Washers (104). 104 See the inset drawing and attach the other 4 104 Shroud Cover (23) in the same manner. 23 8. Note: Some parts have been removed to show 8 this step clearly. 109 96 Slide the two
Resumen del contenido incluido en la página 12
9 Arm Assembly 9. Attach the Butterfly Frame Brace (6) to the Upright (2) with two M8 x 80mm Bolts (100), two M8 Washers (103), and two M8 Nylon Locknuts (78). Do not tighten the Nylon Locknuts yet. 78 100 103 6 100 2 10. Apply grease in the locations shown. Insert a 10 56.5mm Spacer (69) the indicated hole in the Leg Grease Lever (12). Attach the Leg Lever to the Front Leg 116 Hole (10) with an M10 x 61mm Bolt Set (116). Make sure the indicated rod is oriented as shown. Grease 69 116 See the le
Resumen del contenido incluido en la página 13
12. Apply grease to the locations shown and attach 12 the Left Butterfly Bracket (28) to the Butterfly Frame (5) with an M10 x 80mm Bolt (84) and an M10 Nylon Locknut (77). 84 Repeat this step for the Right Butterfly Grease Bracket (29). Tighten the Nylon Locknuts (77, 78, 107) used in steps 2–12. 29 5 77 28 13. Attach a Butterfly Handle (27) to the Left Butterfly 13 Arm (25) with an M10 x 65mm Button Bolt (106), two M10 Washers (80), two 13mm Steel Spacers (109), and an M10 Nylon Locknut (77).
Resumen del contenido incluido en la página 14
15. Orient a Press Arm Handle (17) with the 90° bend 15 at the top as shown in the inset drawing. Attach a 77 80 Press Arm Handle (17) to the Right Press Arm 99 (16) with two M10 x 65mm Button Bolts (106), four M10 Washers (80), four 11mm Spacers (99), 99 80 90° and two M10 Nylon Locknuts (77). 80 Bend 99 Repeat this step for the Left Press Arm (not shown). 17 99 106 80 16 90° Bend 16. Attach the Left Press Arm (15) to the Right Press 16 Arm (16) with an M10 x 110mm Bolt (93), an 89.5mm Spacer
Resumen del contenido incluido en la página 15
18 Cable Assembly 18. See the CABLE DIAGRAMS on page 28 to identi- fy the cables as you assemble them. Grease 90 Identify the Butterfly Cable (50). Grease an 50 M8 x 22mm Shoulder Bolt (90). Attach the Cable to 28 the Left Butterfly Bracket (28) with the Shoulder Bolt 78 and an M8 Nylon Locknut (78). Make sure the flat edge of the Cable is against the Butterfly Arm. Do not overtighten the Shoulder Bolt; the Cable must be able to pivot freely. Flat Edge 19. Wrap the Butterfly Cable (50) over a “V
Resumen del contenido incluido en la página 16
21. Wrap the Butterfly Cable (50) over a “V”-pulley 21 (47). Attach the “V”-pulley, a Long Cable Trap 54 (57), an M10 Washer (80), and two Guards (54) 79 to the Upright (2) with an M10 x 60mm Bolt (79) 57 50 and an M10 Nylon Locknut (77). 47 80 54 2 77 22. Grease an M8 x 22mm Shoulder Bolt (90). Attach 22 the Butterfly Cable (50) to the Right Butterfly Arm (29) with the Shoulder Bolt and an M8 Nylon Locknut (78). Make sure the flat edge of the 50 Cable is against the Butterfly Arm. 90 Grease 78
Resumen del contenido incluido en la página 17
24. Route the Lat Cable (49) over a Thin Pulley (24) 24 and down through the Top Frame (4). Hold the 24 Thin Pulley inside the Top Frame. Insert an M10 x 80mm Bolt (84) through an M10 Washer (80), a 84 19mm Spacer (67), the Top Frame, and the Thin 4 80 Pulley. 49 67 25. Wrap the Lat Cable (49) under a 90mm Pulley 25 (48). Attach the Pulley, a Cable Trap (56), and two Half Guards (55) at the second hole from the top of the two Pulley Plates (60) with an M10 x 50mm Bolt (97) and an M10 Nylon Lockn
Resumen del contenido incluido en la página 18
27. Wrap the Lat Cable (49) around a 90mm Pulley 27 (48) and route the Cable down through the Top 84 Frame (4). Attach the Pulley to the Top Frame 48 80 67 with an M10 x 80mm Bolt (84), two M10 Washers 67 (80), two 19mm Spacers (67), and an M10 Nylon 80 Locknut (77). 77 49 4 28. Set an M12 Large Washer (98) on top of the 28 Weight Tube (20). Thread the M12 Nut (112) all the way onto the Lat Cable (49). 49 Thread the Lat Cable (49) into the Weight Tube (20) two turns. Tighten the M12 Nut (112) ag
Resumen del contenido incluido en la página 19
30. Attach a 90mm Pulley (48) to the Front Leg (10) 30 with an M10 x 65mm Bolt (85), two M10 Washers (80), two 13mm Steel Spacers (109), and an M10 Nylon Locknut (77). Make sure the Leg Lever Cable (51) is under the Pulley. 10 85 80 109 48 51 109 80 77 31. Route the Leg Lever Cable (51) under the 31 89.5mm Spacer (59), through the Upright (2), and under the indicated rod in the Base (1). Wrap the Leg Lever Cable around a 90mm Pulley (48). Attach the Pulley to the Base with an M10 x 45mm Bolt (86
Resumen del contenido incluido en la página 20
33. Wrap the Leg Lever Cable (51) under a 90mm 33 Pulley (48). Attach the Pulley to the Base (1) with an M10 x 45mm Bolt (86), two Half Guards (55), and an M10 Nylon Locknut (77). 51 48 86 55 55 77 1 34. Wrap the Leg Lever Cable (51) over a 90mm 34 Pulley (48). Attach the Pulley to the Double “U”- bracket (61) with an M10 x 45mm Bolt (86), two Half Guards (55), and an M10 Nylon Locknut (77). 77 61 55 48 51 86 55 35. Wrap the Leg Lever Cable (51) under a 90mm 35 Pulley (48). Attach the Pulley to
