Resumen del contenido incluido en la página 1
®
FRAMING NAILER
21 DEGREE ANGLED / 10 GAUGE
Model 04041
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
© ®
Copyright 2004 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Too
Resumen del contenido incluido en la página 2
PRODUCT SPECIFICATIONS Nail Size (.113” to .131” Thick), 10 Gauge (Round Head), 2-3/16” to o 3-1/2” Long; 21 Full Head Nails Magazine Capacity 60 Nails Operating PSI 70 to 125 PSI* Required Air CFM Intake 3 - 3.5 CFM at 90 PSI Accessories Carrying Case, Safety Goggles, Machine Oil, 180 Nails o Features Single Sequential Safety Trip Mechanism, 360 Exhaust Flow Adjustment, Soft Rubber Grip, 1/4” NPT (18 TPI) Air Inlet with Screen, Adjustable Depth Drive Weight 9.9 Lbs. * The air pressure settin
Resumen del contenido incluido en la página 3
8. Use eye and ear protection. Always wear ANSI approved impact safety goggles and appropriate hearing protection. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. Other people in the work area must also wear ANSI approved impact safety goggles. 9. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lubricating
Resumen del contenido incluido en la página 4
18. Use proper size and type extension cord. If an extension cord is required, it must be of the proper size and type to supply the correct current to the compressor without heating up. Otherwise, the extension cord could melt and catch fire, or cause electri- cal damage to the tool. Check your air compressor’s manual for the appropriate size cord. It is also possible that the use of an extension cord may cause your circuit panel fuse to break.
Resumen del contenido incluido en la página 5
28. Transport Nailer safely. Always disconnect air supply when moving the tool in the workplace. Carry the tool by the handle and avoid contact with the trigger. Note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It mu
Resumen del contenido incluido en la página 6
Testing The Single Sequential Safety Trip Mechanism Warning: Even though the nailer should be empty during this procedure, ALWAYS point the Nailer at a piece of scrap wood when testing. 1. The Nailer should not fire if the nose is not depressed against the workpiece. This tool has a single sequential safety trip mechanism, which is designed to prevent inadvertent firing. The tool will only fire if the Safety (38) is resting on the workpiece prior to pulling the Trigger (44). 2. Make sure the
Resumen del contenido incluido en la página 7
Loading Nails (continued) 3. Orient a strip of nails with the points down, and drop the strip of nails into the Magazine (part #71). (See Figure C.) 4. Slide the strip of nails forward in the Magazine (part #71). NOTE: The Magazine will hold 60, 10 gauge nails. (See Figure C.) 5. Unlatch the Feeder Shoe (part #52), and allow the Feeder Shoe to slide forward against the strip of nails. (See Figure C.) OPERATION NOTE: For additional references to the parts listed below, refer to the Assembly D
Resumen del contenido incluido en la página 8
EXHAUST COVER (#4) NAILS (10 GAUGE) (2-3/16” TO 3-1/2” LONG) NOSE (#29) FEEDER SHOE (#52) QUICK COUPLER & AIR SUPPLY HOSE TRIGGER (NOT INCLUDED) (#44) BRACKET A (#35) NOSE (#29) SAFETY (38) FIGURE B To Adjust The Depth To Which A Nail Is Driven 1. The depth to which a nail is driven is controlled by the Safety (part #38). (See Figures B and C). 2. To adjust the depth of drive, loosen the Screw (part #37). Slide Safety (part #38) up or down to the desired position. Then, re-tighten the Screw.
Resumen del contenido incluido en la página 9
SCREW (#37) SAFETY (#38) RUBBER COVER (39) FIGURE C Anytime any maintenance or repairs are done (including clearing jams), FIRST: 1. Disconnect the Nailer from the air hose. 2. Empty the Magazine (71) completely. 3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any brads. 4. Always leave the Magazine (71) open during maintenance. The Magazine is spring- loaded and may cause parts or a nail to fly out of the Nailer
Resumen del contenido incluido en la página 10
FIGURE D Probe in these areas with a screwdriver to release jammed nails. Anytime any maintenance or repairs are done (including clearing jams), FIRST: 1. Disconnect the Nailer from the air hose. 2. Empty the Magazine (71) completely. 3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any brads. 4. Always leave the Magazine (71) open during maintenance. The Magazine is spring- loaded and may cause parts or a nail to fly out of t
Resumen del contenido incluido en la página 11
SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Page 11
Resumen del contenido incluido en la página 12
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTUER AND/ OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
