Resumen del contenido incluido en la página 1
H8S/2378 Series FP-144H
User System Interface Cable
(HS2378ECH61H)
for E6000 Emulator
User’s Manual
ADE-xxx-xxx
Rev. 2.0
4/1/03
Renesas Technology Corp.
Resumen del contenido incluido en la página 2
Cautions 1. Renesas neither warrants nor grants licenses of any rights of Renesas’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Renesas bears no responsibility for problems that may arise with third party’s rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice.
Resumen del contenido incluido en la página 3
Preface Thank you for purchasing this user system interface cable (HS2378ECH61H) for the Renesas’s original microcomputer H8S/2378 Series. The HS2378ECH61H is a user system interface cable that connects an H8S/2678R Series E6000 emulator (HS2678REPI61H; hereinafter referred to as the emulator) to the IC socket for a FP-144H package for the H8S/2378 Series MCU on the user system. i
Resumen del contenido incluido en la página 4
Contents Section 1 Configuration ......................................................................................1 Section 2 Connection Procedures .......................................................................3 2.1 Connecting User System Interface Cable to Emulator Station .........................................3 2.2 Connecting User System Interface Cable to User System ................................................5 2.2.1 Installing IC Socket ........................
Resumen del contenido incluido en la página 5
Section 1 Configuration CAUTION Use an IC149-144-045-B51 socket (manufactured by YAMAICHI ELECTRONICS CO., Ltd.) for the FP-144H package IC socket on the user system. Figure 1 shows the configuration of the HS2378ECH61H user system interface cable for the FP-144H package. Figure 1 HS2378ECH61H User System Interface Cable 1
Resumen del contenido incluido en la página 6
Table 1 lists the HS2378ECH61H components. Please make sure you have all of these components when unpacking. Table 1 HS2378ECH61H Components No. Component Quantity Remarks 1 Cable body 1 2 Cable head 1 3 IC socket 1 For the FP-144H package 4 Socket cover 1 For installing an FP-144H packaged MCU 5 Screws (M2 x 12 mm) 4 For fastening cable head with four flat washers 6 Screws (M2 x 8 mm) 4 For installing an FP-144H packaged MCU with four flat washers 7 CTS screws (M3 x 6 mm) 2 For f
Resumen del contenido incluido en la página 7
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before conne
Resumen del contenido incluido en la página 8
Figure 2 Connecting User System Interface Cable to Emulator Station 4
Resumen del contenido incluido en la página 9
2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. To connect the c
Resumen del contenido incluido en la página 10
2.2.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an FP-144H system interface cable head into the IC socket on the user system, as shown in figure 3. 2.2.4 Fastening Cable Head CAUTION 1. Use a Philips-type screwdriver whose head matches the screw head. 2. The tightening torque must be 0.294 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn t
Resumen del contenido incluido en la página 11
Fasten the user system interface cable head to the IC socket for an FP-144H package on the user system with the four screws (M2 x 12 mm; with four flat washers) provided. Each screw should be tightened a little at a time, alternating between screws on opposing corners. Take special care, such as manually securing the IC socket soldered area, to prevent the soldered IC socket from being damaged by overtightening the screws or twisting the components. Figure 3 Connecting User System Inte
Resumen del contenido incluido en la página 12
2.2.5 Fastening Cable Body Connect the cable body to the cable head. Removing Cable body Push the unfastening jigs. unfastening jig Cable head User system Figure 4 Fastening Cable Body 8
Resumen del contenido incluido en la página 13
2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an FP-144H package (IC149-144-045-B51: manufactured by YAMAICHI ELECTRONICS CO., Ltd.). Note that the dimensions in figure 5 are somewhat different from those of the actual chip's mount pad. Figure 5 Recommended Dimensions for Mount Pad 9
Resumen del contenido incluido en la página 14
2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 6. Figure 6 Dimensions for User System Interface Cable Head 10
Resumen del contenido incluido en la página 15
2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head to the user system, are shown in figure 7. Figure 7 Resulting Dimensions after Connecting User System Interface Cable 11
Resumen del contenido incluido en la página 16
Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.294 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. If a screw is tightened too much, the screw head may break
Resumen del contenido incluido en la página 17
Figure 8 Installing MCU to User System 13
Resumen del contenido incluido en la página 18
Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2378 Series, turn on the emulator according to the procedures described in the E6000 Series Emulator User's Manual (HS2000EPI61HE). 2. Verify the user system interface cable connections by accessing the external memory and ports to check the bus states of the pins. If an error is detected, recheck the soldered IC socket and the location of pin 1. 3. The emulator connected to this user system interface cable suppo
Resumen del contenido incluido en la página 19
Section 5 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of the recommended mount pad for the user system IC socket are different from those of the MCU. 3. This user system interface cable is specifically designed for the HS2678REPI61H emulator. Do not use this cable with any other emulator station. 4. To prevent breaking of wires in the c
