Resumen del contenido incluido en la página 1
TABLE OF CONTENTS
SPECIAL NOTES ON LCD MONITORS........................................................ 1
INFORMATION FOR YOUR SAFETY AND COMFORT ............................... 2
UNPACKING .................................................................................................. 5
ATTACHING / REMOVING THE BASE......................................................... 6
SCREEN POSITION ADJUSTMENT............................................................. 7
CONNECTING THE POWER CORD
Resumen del contenido incluido en la página 2
T230H SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.
Resumen del contenido incluido en la página 3
T230H INFORMATION FOR YOUR SAFETY AND COMFORT Safety instructions Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. CAUTION for accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power to the equipment, be sure to unplug the power cord from the electrical outlet. Warnings
Resumen del contenido incluido en la página 4
T230H Product servicing Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel. Unplug this product from the wall outlet and refer servicing to qualified service personnel when: the power cord or plug is damaged, cut or frayed liquid was spilled into the product the product was exposed to rain or water the product has been dropped or the case has been
Resumen del contenido incluido en la página 5
T230H Taking care of your vision Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting, poorly focused screens, very small typefaces and low-contrast displays could stress your eyes. The following sections provide suggestions on how to reduce eyestrain. Eyes Rest your eyes frequently. Give your eyes regular breaks by looking away from the monitor and focusing on a distant point. Blink frequently to keep your eyes from drying out. Display
Resumen del contenido incluido en la página 6
T230H UNPACKING Please check the following items are present when you unpack the box, and save the packing materials in case you will need to ship or transport the monitor in future. LCD Monitor AC Power Cord D-Sub Cable DVI Cable (Optional) HDMI cable (Optional) USB cable Audio cable User Manual Quick Start Guide EN- 5
Resumen del contenido incluido en la página 7
T230H ATTACHING / REMOVING THE BASE Install: Align the base with the stand and push the base towards the top ofthe monitor, and then rotate the base clockwise. Tighten the screw clock-wise. Remove: Reverse the steps to remove the base. EN- 6
Resumen del contenido incluido en la página 8
T230H SCREEN POSITION ADJUSTMENT In oder to optimize the best viewing position, you can adjust the height/tilt/swivel of the monitor. Height Adjustment After pressing the top of the monitor, push the lock button towards right,then you can adjust the height of the monitor. Tilt Please see the illustration below for an example of the tilt range. EN- 7
Resumen del contenido incluido en la página 9
T230H Swivel With the built-in pedestal, you can swivel the monitor for the mostcomfortable viewing angle. EN- 8
Resumen del contenido incluido en la página 10
T230H CONNECTING THE POWER CORD Check first to make sure that the power cord you use is the correct type required for your area. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240 V AC voltage areas. No user-adjustment is required. Plug one end of the power cord to the AC Inlet, plug another end to a proper AC outlet. For unit using at 120 V AC: Use a UL Listed Cord Set, Type SVT wire and plug rated 10 A/125 V. For unit using at 2
Resumen del contenido incluido en la página 11
T230H POWER SAVING The monitor will be driven into Power Saving” mode by the control signal from the display controller, as indicated by the amber-color power LED. State LED Light ON Blue Power Saving Mode Amber The power saving states will be kept until a control signal has been detected or the keyboard or mouse is activated. The recovery time from Active OFF state back to ON state is around 5 seconds. DDC To make your installation easier, the monitor is able to Plug and Play
Resumen del contenido incluido en la página 12
T230H CONNECTOR PIN ASSIGNMENT 15-Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Logic Ground 3. Blue 11. Monitor Ground 4. Monitor Ground 12. DDC-Serial Data 5. DDC-return 13. H-Sync 6. R-Ground 14. V-Sync 7. G-Ground 15. DDC-Serial Clock 8. B-Ground EN- 11
Resumen del contenido incluido en la página 13
T230H 24-Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. TMDS Data2- 13. TMDS Data3+ 2. TMDS Data2+ 14. +5V Power TMDS Data 2/4 GND(return for 3. 15. Shield +5V hsync.vsync) 4. TMDS Data4- 16. Hot Plug Detect 5. TMDS Data4+ 17. TMDS Data0- 6. DDC Clock 18. TMDS Data0+ 7. DDC Data 19. TMDS Data 0/5 Analogue Vertical 8. 20. TMDS Data5- Sync 9. TMDS Data1- 21. TMDS Data5+ 10. TMDS Data1+ 22. TMDS Clock Shield TMDS Data 1/3 11. 23. TMDS Clock+ Shield
Resumen del contenido incluido en la página 14
T230H STANDARD TIMING TABLE Mode Resolution 1 VGA 640 x 480 60 Hz 2 VGA 640 x 480 66.6 Hz 3 VESA 720 x 400 70 Hz 4 SVGA 800 x 600 56 Hz 5 SVGA 800 x 600 60 Hz 6 XGA 1024 x 768 60 Hz 7 XGA 1024 x 768 70 Hz 8 VESA 1152 x 864 75 Hz 9 WXGA 1280 x 800 60 Hz 10 SXGA 1280 x 1024 60 Hz 11 WXGA+ 1440 x 900 60 Hz 12 UXGA 1920 x 1080 60 Hz EN- 13
Resumen del contenido incluido en la página 15
T230H INSTALLATION To install the monitor to your host system, please follow the steps as given below: Steps Make sure both the monitor and computer are powered-OFF. 1. 1-1 Connect Video Cable Connect the VGA video cable to the computer. 1-2 Connect Digital Cable (Optional) . Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the computer's port. 1-3 Connect HDMI Cable (Optional) . Connect the HDMI cable to the computer. 1-4 Conne
Resumen del contenido incluido en la página 16
T230H USER CONTROLS Front Panel Controls 1.Power Switch: To turn ON or OFF the power. 2.Power LED: Lights up to indicate the power is turned ON. 3.Empowering / Exit: 1) When OSD menu is in active status, this button will act as EXIT-KEY(EXIT OSD menu). 2) When OSD menu is in off status, press this button to select scenario mode. 4.Auto Adjust button / Exit: 1)When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). 2)When OSD menu is in off st
Resumen del contenido incluido en la página 17
T230H HOW TO ADJUST A SETTING 1. Press the MENU-button to activate the OSD window. 2. Press < or > to select the desired function. 3. Press the MENU-button to select the function that you want to adjust. 4. Press < or > to change the settings of the current function. 5. To exit and save, select the exit function. If you want to adjust any other function, repeat steps 2-4. P/X Series OSD behave When user press “MENU” button on front bezel A. Acer eColor Management If selected
Resumen del contenido incluido en la página 18
T230H ADJUSTING THE PICTURE The descriptions for function control LEDS A. Acer eColor Management Main Menu Sub Menu Sub Menu item Description icon icon N/A User mode User defined. Settings can be fine-tuned to suit any situation Optimal balance of brightness and contrast prevent N/A Text mode eyestrain. The most comfortable way to read onscreen text N/A Standard mode Default Setting. Reflects native display capability N/A Graphic mode Enhances colors and emphasize fine detail
Resumen del contenido incluido en la página 19
T230H Main Menu Sub Menu icon Sub Menu item Description icon Adjust the horizontal position. H. Position (available in Analog mode only) Adjust the vertical position. V. Position (available in Analog mode only) N/A Warm Set the color temperature to warm white. N/A Cool Set the color temperature to cool white. User /Red User /Green Adjusts Red/Green/Blue intensity User /Blue N/A English N/A 繁體中文 N/A Deutsch N/A Français Multi-language selection. N/A Español N
Resumen del contenido incluido en la página 20
T230H Acer eColor Management OSD User Text Standard Movie Graphic mode mode mode mode mode Operation instructions Acer eColor Management Step 1: Press “ Key” to open the Acer eColor Management OSD and access the scenario modes Step 2: Press “<” or “>” to select the mode Step 3: Press “Auto Key” to confirm the mode and run Auto Adjust Features and Benefits M Mo od de e F Fe ea attu ur re es s B Be en ne effiitts s S St ta an nd da ar rd d Default settings Refl
