Resumen del contenido incluido en la página 1
17 inch Wide Screen
TFT LCD Monitor
HB175A
USER’S MANUAL
Resumen del contenido incluido en la página 2
User’s Manual Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
Resumen del contenido incluido en la página 3
User’s Manual Recycling Information We, the Hanns.G care very much about our environment protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life. These devices contain recyclable materials, which can be re-decomposed and re-integrated into brand-new marvels. On the contrary, other material can be classified to hazardous and poisoned substances. We strongly encourage you to c
Resumen del contenido incluido en la página 4
User’s Manual TABLE OF CONTENTS SAFETY NOTICE ......................................................................................................5 PRECAUTIONS.....................................................................................................5 SPECIAL NOTES ON LCD MONITORS ..........................................................6 BEFORE OPERATING THE MONITOR ...............................................................7 FEATURES..................................
Resumen del contenido incluido en la página 5
User’s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference
Resumen del contenido incluido en la página 6
User’s Manual SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0
Resumen del contenido incluido en la página 7
User’s Manual BEFORE OPERATING THE MONITOR FEATURES • 17” Wide screen TFT Color LCD Monitor • Crisp, Clear Display for Windows • Recommended Resolutions: 1440 X 900 @60Hz ® • EPA ENERGY STAR • Ergonomic Design • Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: LCD Monitor Screen Base Cables and User manual Power Cord VGA Cable Audio Cable User’s manual Warranty card 7
Resumen del contenido incluido en la página 8
User’s Manual INSTALLATION INSTRUCTIONS INSTALL REMOVE Figure.1. Installing and Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer section of the base points forward. 3. Snap the monitor into its base. A clear click sound will affirm that the base is connected correctly. 4. Verify that the monitor is securely attached to the base by looking at the bottom of the base and making sure that the clips are fully en
Resumen del contenido incluido en la página 9
User’s Manual MAKING CONNECTIONS CONNECTING TO A PC Turn off your computer before performing the procedure below. 1. Connect one end of the D-Sub cable to the back of the monitor and connect the other end to the computer’s D-Sub port. 2. Connect the audio cable between the monitor's audio input and the PC's audio output (green port). 3. Plug one end of the AC power cord to the LCD monitor’s AC input socket, and the other end to the Wall outlet. 4. Turn on your monitor and compu
Resumen del contenido incluido en la página 10
User’s Manual CONNECTING TO A A/V DEVICE: Connect A/V devices via the D-sub and Audio Line in connectors at the back of the monitor. 1. Connect one end of the D-Sub cable to the back of the monitor and connect the other end to the D-sub to YPbPr adapter cable. 2. Connect the Y (green) connector on the D-sub to YPbPr adapter cable to the Y output connector on the A/V device. 3. Connect the Pb (blue) connector on the D-sub to YPbPr adapter cable to the Pb/Cb output connector on the A/V
Resumen del contenido incluido en la página 11
User’s Manual ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, and then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle. • The monitor’s angle is adjustable from 0 ° to 20 °. Monitor Angle Figure.4. NOTES: • Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. • Be careful
Resumen del contenido incluido en la página 12
User’s Manual OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the front panel of the monitor (See Figure 5). By changing these settings, the picture can be adjusted to your personal preference. • The power cord should be connected. • Connect the Signal cable from the monitor to the VGA card. • Press the power button to turn on the monitor. The power indicator will light up. Figu
Resumen del contenido incluido en la página 13
User’s Manual FRONT PANEL CONTROL • Power Button: Press this button to switch ON/OFF monitor’s power. • Power Indicator: Green — Power On mode. Orange — Power Saving mode. • MENU / RETURN: 1. Turn the OSD menu on/off or return to the previous menu. 2. Exit OSD menu when in volume OSD status. • Adjust < / >: 1. Adjust Brightness and volume when the OSD is off. 2. Navigate through adjustment icons when OSD is ON or adjust a function when function is activated. • AUTO But
Resumen del contenido incluido en la página 14
User’s Manual HOW TO ADJUST A SETTINGS BRIGHTNESS/CONTRAST Adjust the brightness value of the display according to your BRIGHTNESS preference. Select BRIGHTNESS option to adjust the brightness value. Adjust the contrast value of the display according to your preference. CONTRAST Select CONTRAST option to adjust the contrast value. Optimal setting for high contrast images or videos. The dark and light areas of the image are automatically detected, and the contrast is X-CONT
Resumen del contenido incluido en la página 15
User’s Manual COLOR SETTING WARM Adjust the color temperature value of the display according to your NATURE preference: WARM /NATURE/ COOL. COOL Move the cursor to the User option and select it, To adjust the red, enter the R option and adjust the level. USER To adjust the green, enter the G option and adjust the level. To adjust the blue, enter the B option and adjust the level. IMAGE SETTING Select the H-POSITION option to shift the screen image to the left or
Resumen del contenido incluido en la página 16
User’s Manual Select the CLOCK option to reduce the vertical flicker of characters CLOCK on the screen. Enter the option and adjust the level. Select the PHASE option to reduce the horizontal flicker of characters PHASE on the screen. Enter the option and adjust the level. Select the SHARPNESS option to adjust the sharpness of the display. SHARPNESS Set the value from -2 to 2. OSD SETTING Select LANGUAGE option to change the language of the OSD. Enter the option and
Resumen del contenido incluido en la página 17
User’s Manual SYSTEM Select the VOLUME option to change the volume level. Enter the VOLUME option and adjust the level. MUTE Select MUTE option to switch the function On or Off. Select the DDC/CI option to switch the function On or Off. (Dual DDC/CI input mode optional) Select the FACTORY RESET option to reset to the monitor’s FACTORY RESET default setting. This will erase the current settings. Enter the option and select On or Off. Display Horizontal frequency/Vertical
Resumen del contenido incluido en la página 18
User’s Manual PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel. THIS MONITOR WILL APPEAR TO BE NON-F
Resumen del contenido incluido en la página 19
User’s Manual TECHNICAL SUPPORT (FAQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION *Check if the Power Switch is in the ON position Power LED is not on *Power Cord should be connected *Check if the PC system is Plug & Play compatible No Plug & Play *Check if the Video Card is Plug & Play compatible *Check if any plug pins on the D-Sub connector are bent The display is too dark or too *Adjust the Contrast and Brightness Controls. bright. Picture bounces or a wave
Resumen del contenido incluido en la página 20
User’s Manual ERROR MESSAGE & POSSIBLE SOLUTIONS CABLE NOT CONNECTED: 1. Check that the signal-cable is properly connected, If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT: Your computer has been set to unsuitable display mode, set the computer to display mode given in the following table. FACTORY PRESET TIMING TABLE: HORIZONTAL VERTICAL MODE RESOLUTION FREQUENCY (KHz) FREQUENCY (Hz) 1 6
