Resumen del contenido incluido en la página 1
Resumen del contenido incluido en la página 2
Table of Content Operating Instructions Safety Precautions _________________________________ 2 Care and Maintenance ______________________________ 3 CHAPTER 1 Introduction _______________________________________ 4 Factory-Preset Modes _______________________________ 5 Specification LCD-1700VRZ Specification _______________________ 6 CHAPTER 2 Installing the Monitor _______________________________ 8 Follow these steps to install the monitor ___________________ 8 Control Function
Resumen del contenido incluido en la página 3
Safety Precautions This monitor is manufactured and tested on the principle that the user’s safety comes first. However, improper use or installation may not only damage the monitor but endanger the user as well. As a safety precaution, go over the following WARNINGS carefully before installation, and keep this guide handy. Warnings: l This monitor should be operated only at the correct power sources indicated on the label at the rear end of the monitor. If you are unsure of the po
Resumen del contenido incluido en la página 4
Care and Maintenance Care l Avoid exposing your monitor directly to sunlight or other heat sources. Place your monitor away from the sun to reduce glare. l Put your monitor in a well-ventilated area. Do not place anything heavy on top of your monitor. l Make certain that your monitor is installed in a clean and moisture-free area. l Keep your monitor away from magnets, motors, transformers, speakers, and TV sets. Safety Tips l If smoke, an abnormal noise or an odor comes out of
Resumen del contenido incluido en la página 5
CHAPTER 1 Introduction BEFORE INSTALLING YOUR MONITOR Read this manual cover to cover. PAY ATTENTION to all WARNING and CAUTIONS DO NOT use computer components not recommend by the manufacture Do not attempt to service the monitor your self. If a problem occurs, contact the manufacture's authorized service center ABOUT YOUR MONITOR This monitor is a microprocessor-controlled, color monitor that uses a TFT LCD panel. The monitor conforms to EPA Energy Star and VESA DPMS (Displ
Resumen del contenido incluido en la página 6
FACTORY-PRESET MODES Table 1 shows standard video mode setting that has been pre-adjusted at the factory for accurate video display. These setting are stored in the monitor's memory Table 1. Factory-Preset Modes PC mode Mode Resolution H-Freq.(KHz) V-Freq(Hz) NEC 640x400 24.83 56.4 VGA 640x350 31.47 70 720x400 31.47 70 640x480 31.47 60 640x480 37.86 72 640x480 37.5 75 SVGA 800x600 35.16 56.3 800x600 37.88 60.3 800x600 48.08 72.2 800x600 46.87 75 XGA 1024x768 48.36 60 1
Resumen del contenido incluido en la página 7
Specifications l LCD-1700VRZ 17” LCD 1U Rack Display Monitor Overall Dimension(HxWxD): 483 x 515 x 43 mm Effective Display area(H/V): 337.92 x 270.34 mm Display colors: 16M colors Scan Frequencies: Horizontal 31.47K to 80KHz Vertical 60Hz to 75Hz Number of Pixels: 1280x1024 pixels Pixel pitch: 0.264x0.264 mm Picture Tube: 17" TFT LCD panel Power: Input 110-240VAC(auto-sensing) Frequency: 48-62Hz Consumption 45Watts maximum (on) 3 Watts
Resumen del contenido incluido en la página 8
Operations: User Controls On/Off Power Button, +/- and Up/down keys On Screen Display Auto adjustment, Brightness, contrast color temperature, Hue, Tint, Source select, PIP setup H-position, V-position, OSD position Audio volume, bass, treble, mute Load default Control Type: Digital Compatibility: IBM and compatible, Apple Macintosh, NEC Environmental Limits: Operating Temp 32° to 103°F ( 0° to 40°C ) Storage Temp. -4° to 140°F ( -20° to 60°C
Resumen del contenido incluido en la página 9
BNC out BNC In Audio R/L AV1 S video YcbCr Component Audio out DGB In DC power Jack Chapter 2 PRODUCT PACKAGE Open the shipping carton and check the contents. If any items are missing or damaged, contact your dealer immediately. The package should include the following items l Analog Color TFT LCD Monitor l Accessory Box: 1. VGA cable x 1 2. AC to DC adapter x 1 3. Power Cord x 1 4. User’ s manual/Warranty Card x 1 5. Audio cable x 1 6. Mini DIN/RCA cable (for Compone
Resumen del contenido incluido en la página 10
CONTROL FUNCTIONS The Monitor control functions are located on the right corner of the front view side. They are shown in the figure below and described in the following paragraphs. The control key description 1. : Power Switch 2. - : Decrement 3. + : Increment or source select 4. Ñ : Move to the next item / Brightness control 5. D : Move to the previous item / Brightness control 6. MENU : Activate the on screen display function 9
Resumen del contenido incluido en la página 11
DESCRIPTION 1. : Power switch Use the power switch to turn ON or OFF power. We recommend turning your system power on first, then the LCD monitor. 2. - & + : decrement or increment the value The two keys are decrement or increment the value or enter into the sub-menu. Note: The + key can change the source directly when de-activation OSD screen. 3. Ñ & D : Select key / Brightness Control keys The two keys have two functions, controlled by the MENU key. When activatin
Resumen del contenido incluido en la página 12
CHAPTER 3 ADJUSTING THE MONITOR VGA OSD main screen 1024x768 48.5K 60.2 3 Auto Adjustment - Execute + VER XGA-KDC45-5100 1. Each time, when pressing the menu key, the screen will show as above. You can see the 3mark that means the selected item. Then you can change the setting through + or -.key. 2. Pressing the Sel key to move the arrow down or up. If the selected item has many option to choose, press – or + to enter in
Resumen del contenido incluido en la página 13
The VGA main screen Auto adjustment § Automatically adjusts the phase and position of the LCD monitor for the best view setting Color temperature setting § Provide 9300K, user mode, and 6500K option Brightness adjustment § Let user adjust the brightness. The range if from 0 to 99 . Contrast setup § Provide user to separately adjust each R, G and B contrast and intensity value. When Move to this icon, and press – or + key, then the screen will show below 1024x768
Resumen del contenido incluido en la página 14
Geometry setup § We provide Pixel Clock, Phase, H Position, V Position, OSD H Position, OSD V Position and Txt/Gft option to change. § Pixel Clock: Adjust the viewing screen size. The range is from 0 to 99 Phase: Adjust phase tracking to reduce the display flicker. The range is from 0 to 31 § H Position: Move the whole screen horizontally. The range is from 0 to 120. § V Position: Move the whole screen vertically. The range is from 0 to 100. § OSD H Position: Move the OSD horizo
Resumen del contenido incluido en la página 15
S-video, PIP YCbCr and PIP off for user’ s selection. Note: The PIP function is only valid on video on VGA screen. We can’ t support video on video screen Speaker volume control § We provide Volume, Bass, Treble, Mute and PIP audio for audio setup. § Volume: Adjust the speaker volume. The range is from 0 to 32. § Bass: Adjust the speaker Bass value. The range is from 0 to 10. § Treble: Adjust the speaker Treble value. The range is from 0 to 10. § Mute: Enable or disable the Mute func
Resumen del contenido incluido en la página 16
Chapter 4 VIDEO ADJUSTMENT Video OSD Screen NTSC 15.7K 60.2 3 Brightness - Adjustment + 49 VER XGA-KDC45-5100 1. Each time, when pressing the menu key, the screen will show as above. You can see the 3mark, that means the selected item Then you can change the setting through + or -.key. 2. Pressing Sel key to move the arrow down or up. If the selected item has many option to choose, press – or + to enter into the sub-men
Resumen del contenido incluido en la página 17
Intensity adjustment § Adjust the screen intensity value. The range is from 0 to 255 Tint adjustment § Adjust the screen Tint value. The range is from 0 to 127 Hue adjustment § Adjust the screen Hue value. The range is from 0 to 255 Geometry setup § We provide Sharpness, H Position, V Position, OSD H Position, and OSD V position. § Sharpness: Adjust the screen sharpness level. The range is from 0 to 15 § H position: Move the screen horizontally. The Range is from 0 to 20 § V Posi
Resumen del contenido incluido en la página 18
Appendix Troubleshooting Procedures This LCD Monitor was pre-adjusted in the factory with standard VGA timing. Due to output timing differences among various VGA cards, you may initially experience an unstable or unclear display when a new display mode or new VGA card is selected. This LCD Monitor Supports Multiple VGA Modes. Refer to the timing table for a listing of factory-preset modes supported by this LCD Monitor. PROBLEM: There is no LCD Display If there is no display on the
