Instruction d'utilisation Ace Hardware

Résumé du contenu de la page N° 1

®
Hardwired
Electronic
Chime
© 2005 598-1224-00

Résumé du contenu de la page N° 2

598-1224-00 -2- Cover Pin (Used for Base Orientation CHIME REPLACEMENT INSTALLATION Hanging Type Covers) Marking IMPORTANT: Proper installation requires a diode on the front door push button. See Diode Installation Instructions (page 5) after completing steps 1 through 10 below. Note: Electrical work must be in accordance with national and local electrical codes. If in doubt, consult a qualified electrician. Volume Control 1. Verify transformer power rating. Power must be supplied from a 16

Résumé du contenu de la page N° 3

VOLUME FRONT TUNE A B FRONT TRANS REAR 8. Route wires through wire entrance hole in new chime base. 9. Mount chime base to wall using screws and anchors provided. (Drill 7/32" diameter pilot hole for wall anchors.) 10. Connect wire “F” to screw terminal marked “FRONT”. Connect wire “T” to screw terminal marked “TRANS”. Connect wire “R” to screw terminal marked “REAR”* (See Figure 2). 11. Install chime cover (see page 4). 12. Connect diode to front push button (see page 5). *Note:

Résumé du contenu de la page N° 4

598-1224-00 -4- INSTALL CHIME COVER Cover Pin Place chime cover securely over base. • For hanging type cover: Remove, turn over, and reinstall the cover pin (see Figure 3). Hang cover on cover pin. • For snap-on type cover: Apply pressure to the cover until it snaps into place (see Figure 4). Firmly grasp cover and pull to remove from base. Note: Never use cleaners or polishes. Never use any fluids on the electronic chime mechanism. Use dry cloth to clean chime cover and base. Figure 3 - Tur

Résumé du contenu de la page N° 5

DIODE INSTALLATION INSTRUCTIONS A small electrical component called a “diode” is required for this chime to play the entire eight-note tune. This diode must be installed on the terminal screws of the front door push button (see Figure 5). If not already installed on push button, attach supplied diode as shown below. If, with the diode in place, the chime does not play the complete eight-note melody, see T r oubleshooting , page 6. Diode Front Door Push Button (Styles May Vary) Figure 5 - At

Résumé du contenu de la page N° 6

598-1224-00 -6- TROUBLESHOOTING Chime does not sound: • Check Chime: Disconnect wire from terminal marked “TRANS”. Have someone operate push button at front door while you mo- mentarily touch the “TRANS” wire to terminal marked “FRONT”. You will see a small spark if push button, wiring, and transformer are operating properly. Repeat the steps for “REAR” terminal and rear push button. If wiring between transformer and push button(s) check out properly, replace chime. • Check Transformer: Test t

Résumé du contenu de la page N° 7

TECHNICAL SERVICE Please call 1-800-858-8501 for assistance before returning product to store. If you experience a problem, follow this guide. You may also want to visit our Web site at: www.desatech.com. If the problem persists, call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to: DESA Specialty Products™ ATTN: Technical Service Specialty Products P.O. Box 90004, Bowling Green, KY 42102-9004 * If contacting Technical Service, please have the following i

Résumé du contenu de la page N° 8

F R O N T T R A N S R E A R F 598-1224-00 -8- Front Door Push Button With Diode Chime Transformer T Rear Door Push Button (If Applicable) Chime System Wiring Diagram R