Instruction d'utilisation Chamberlain 1025

Résumé du contenu de la page N° 1

TM
exit
DEVICE SETUP ADD USER ENTER DELETE USERBLOCK USER
SCROLL
RELAY OUTPUT
N.O. contacts
GRANT ACCESS
12/24 EXT.
KEEP TERMINALS COVERED VOLT 24 VOLTS GRANT
HAZARDOUS VOLTAGES! 0-9, A-Z
SERIAL PORT SELECT VAC AC/DC SWITCH
ACRx 2
MODEL 1025LM
Access Control Receiver
ACRx 2 Model 1025
OWNERS MANUAL
To comply with FCC/IC rules, adjustment or modification of receiver and/or
transmitter is prohibited, except for changing the code setting and replacing the
transmitter battery. THERE ARE NO USER SER

Résumé du contenu de la page N° 2

Push Button Common ACRX & ANTENNA MOUNTING INSTRUCTIONS Mounting the Box • The ACRx 2 antenna system can be configured in several ways. Each installation is different, so there is no best antenna Choose a location for the ACRx 2 1025 control box which is: system. Try the different configurations of antenna placement • Protected from tampering and amplifier until the best range is encountered. Do this • As close to the approaching vehicles as possible for best BEFORE hard -mounting the antenna

Résumé du contenu de la page N° 3

ANTENNA CONFIGURATIONS A. No amplifier, no cable (short radio range). B. No amplifier, coax cable used (short radio range). Antenna is mounted direct to ACRx 2. Antenna is mounted away from the ACRx 2 at the end of the 15ft cox cable. COAXABLE CABLE ANTENNA ANTENNA ACRx 16 CHARACTERLCD Lift-Master model G1000 ACRx Lift-Master model G1000 16 CHARACTERLCD exit exit DEVICE ADD ENTER DELETE BLOCK SETUP USER USER USER DEVICE ADD ENTER DELETE BLOCK Z 0 SETUP USER USER USER Z 0 A 9 RELAY OUTPUT V S E

Résumé du contenu de la page N° 4

• Momentary Close: The relay contacts will close for 1/3 OPERATION seconds each time a valid user’s transmitter code is received. The controls and display on the ACRx 2 panel are very simple This is the factory default state of the ACRx 2, and the most for ease of operation. Most programming tasks require pushing commonly used. one button for the desired operation, then completing the • On When Receiving: The relay contacts will close when a displayed instructions. A summary of these procedures

Résumé du contenu de la page N° 5

“Blocked: at ”. This prints each time a Block and Unblock Users transmitter code is received which is blocked. Access is not Press the BLOCK USER button. The display will show “USER granted. The User ID of the transmitter and the date and time of ID = _____”. Turn the knob until the first letter of the User ID is the attempt are recorded. shown, then press ENTER. Repeat until the entire User ID is (In all these cases the date and time recorded depend upon the displayed. date

Résumé du contenu de la page N° 6

COMPONENT LAYOUT Antenna Mounting Display Display Contrast Holes Adjustment 2 TM MODEL 1025LM SETUP/EXIT ADD USER ENTER DELETE USERBLOCK USER SCROLL GRANT ACCESS RELAY OUTPUT 12/24 EXT. 0-9, A-Z N.O. contacts N.E.C. CLASS 2 VOLT 24 VOLTS GRANT ❷ SERIAL PORT WIRING ONLY SELECT VAC AC/DC SWITCH Serial Port Grant Output Voltage Select Power Supply for Computer Access Terminals or Printer Jumpers Inputs Button 6 ❷

Résumé du contenu de la page N° 7

TROUBLESHOOTING Problem Remedy LCD display is blank. • Power not connected; check plug and wires. • ACRx 2 is broken; repair or replace. LCD display is on but ACRx 2 does not function properly. • Turn power off, then on again. • Check 24V/12V jumper. All users have short radio range, green light is flashing. • A transmitter is stuck on. Use M-18 test set to locate and disable transmitter. All users have short radio range, green light is off. • Radio interference; try moving antenna lo

Résumé du contenu de la page N° 8

©1995, The Chamberlain Group, Inc. 01-12615B All Rights Reserved Printed in Mexico