Instruction d'utilisation Char-Broil PATIO BISTRO 11601558

Résumé du contenu de la page N° 1

assembly
guide
Model Number:
11601558


Propane cylinder
sold separately.
Estimated time required for assembly: 1 Hour
PROPANE
(English)
42804394 • 06/02/2010

Résumé du contenu de la page N° 2

2 A, B, C, Assembly: ASSEMBLY GUIDE CAUTION: For your safety, before operating, Read Product Guide & Outdoor Cooking Guide provided with this grill. *SAFETY First…..Grill components may have sharp edges. Be careful when handling grill parts during assembly. We suggest that you wear a sturdy pair of leather gloves while handling the grill parts. BEFORE You begin assembly of your grill…. 1. Carefully remove all components from the carton. 2. Familiarize yourself with the components

Résumé du contenu de la page N° 3

3 Grill Parts Diagram ASSEMBLY GUIDE K H FF S C A V I CC T X J G L W D B DD F N Y O E P R U GG M HH Q BB BB Z AA EE Key Qty Description Key Qty Description Key Qty Description O 1 Rear Leg Set CC 1 Ignition Module A 1 Grill Lid DD 1 Electrode Wire P 1 Front Leg Set B 1 Lower Body EE 1 Ignitor Electrode Q 1 Grease Tray C 1 Heat Tent FF 2 Lid Bumper R 2 Hubcap D 1 Burner GG 1 Match Light Hole Cover S 1 Hose, Valve, Regulator Assembly E 1 Tank Retainer Bolt HH 1 Grate Cleaning Tool T 1 Warming

Résumé du contenu de la page N° 4

4 ASSEMBLY GUIDE GRILL CART Assembly Part Qty A1– Tank Retainer Ring 1 . A2– Cart Base 1 A3– Tank Retainer Bolt 1 Wheel Retaining Clip A4– Front Leg Set 1 1/4x20-1/2" 3/8-16 Nut (qty 2) screw A5– Rear Leg Set 1 (qty 2) (qty 4) A6– Wheels 2 – A7 Hubcap 2 Axle Bolt (qty 2) A1 A3 1/4-20 Nut (qty 4) Step 1 Assemble Tank Retainer Ring (A1) to the Cart Base (A2) by aligning studs into corresponding holes. Secure with 4 each, 1/4-20 nuts using a

Résumé du contenu de la page N° 5

5 ASSEMBLY GUIDE GRILL CART Assembly . Part Qty – A8 1 Cart Bracket 1/4x20-2" – A9 Leg End Cap 2 screw (qty 4) 1/4-20 Nut 1/4-20 Nut (qty 4) #10x3/8" screw (qty 2) Step 3 - Carefully turn the Cart Assembly over and allow it to rest on the tops of the leg assemblies. Assemble the Cart Bracket (A8) to the Cart Assembly by by inserting 4 each 1/4- 20x2" screws int0 into corresponding holes as shown. Allow the Cart Bracket to rest on the floor, this will help with

Résumé du contenu de la page N° 6

6 GRILL BODY Assembly ASSEMBLY GUIDE Part Qty. . B1– Lower Body 1 10-24x3/8" screw B2– Wind Shield 1 (qty 3) 10-24 Nut Fiber Washer 1/4-20 Nut 1/4-20x3/4" (qty 10) (qty 5) (qty 2) B3– Grill Lid 1 Hinge screw (qty 2) ASSEMBLY Step 1 - Attach the Lower Body (B1) to the Cart Assembly Step 3 - Attach the Wind Shield (B2) to the Lower Body by aligning the studs on the bottom of the grill with the (B1) by aligning the holes in the panels with the correspondin

Résumé du contenu de la page N° 7

7 GRILL FINAL Assembly ASSEMBLY GUIDE NOTE: The Cooking Grate may have sharp edges. Be Part Qty. very careful when handling the Cooking Grate. You C1 – Heat Tent 1 should wear gloves when handling the Cooking Grate. C2 – Cooking Grate 1 The cooking grate ridges should run from front to back of C3 – Warming Rack 1 the grill as shown below. Be sure that the cooking grate C4 – 1 Control Knob rests squarely on the brackets spaced around the lower C5 – Grease tray 1 body.

Résumé du contenu de la page N° 8

- + 8 GRILL FINAL Assembly ASSEMBLY GUIDE Part Qty. C6 – Battery 1 C7 – Electronic Ignition Module 1 10-24x3/8" screw Fiber Washer C8 – Lid Handle 1 (qty 2) (qty 2) NOTE: The Ignition wiring shown below will only fit into the module one way. Be sure the wires are routed away from the heat source. Do not allow the wires to rest against hot areas of the grill. Step 3 - Install the Electronic Ignition Module, Unscrew the Battery Cap and module nut from the m