Résumé du contenu de la page N° 1
-
Remote Control Alarm System with CoolGlow & SecurWatch®
on your choice of a Remote Alarm System by Crimestopper Security Products Inc.
This system features both a 4 - Button CoolGlow Transmitter and a SecurWatch® Sports Watch
that feature anti code - grabbing technology. The remote code changes with every use of the
transmitter making it impossible to scan or record the codes for use later on. This booklet contains the
information necessary for installing, using,
Résumé du contenu de la page N° 2
- 5 - - - - - - - E - - CRIMESTOPPER SECURITY PRODUCTS, INC. 1770 S. TAPO STREET, SIMI VALLEY, CA. 93063 support@crimestopper.com mail: tech Website: www.crimestopper.com 4:30pm Pacific Standard Time day 8:00am Fri Monday 6880 998 TECHNICAL SUPPORT (800) System Wiring Diagram………………….……………………………………………………………………………16 Carjack Operation……………………………………………………………………………………..………………..15 14 Operation………………………………..…………………
Résumé du contenu de la page N° 3
BEFORE BEGINNING , check a ll vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, AND BATTERY). TO PREVENT A POSSIBLE DEAD BATTERY remove vehicle dome light fuse while working on the vehicle. MAKE CERTAIN TO REINSTALL FUSE PRIOR TO TESTING DO NOT EXCEED MAXIMUM OUTPUT RATINGS! - SERIOUS DAMAGE MAY OCCUR. LIMITS FOR ALARM FUNCTIONS ARE LISTED WHERE APPLICABLE. IF UNSURE ABOUT CURRENT LOAD, - METER. REMOVE MAIN SYSTEM FUSE(S) before jump
Résumé du contenu de la page N° 4
WI - Vehicle’s Battery Positive Terminal. BLACK WIRE: CHASSIS GROUND THIS WIRE MUST BE CONNECTED TO TH Connect to a (+) Ignition Wire that shows +12 V ORANGE WIRE: ( - Connect to switched parking light wire at back of light switch or connect directly to one of the parking lights at the front require additional parts due to separate left and right circuits. BLUE WIRE: ( - t trigger for a grounding hood or trunk pin switch. Connect to existing hood and trunk
Résumé du contenu de la page N° 5
WHITE/RED WIRE: ( - Connects the same way as Remote Output 1 above to activate or control a second AUX device or function. This output will provide a momentary negative signal when AUX 2 is activated. below for possible wiring configurations. + PINK IGN SW PINK + IGN FULL TIME OPTIONAL CAR JACK WIRING: (Not Included) +12 V TOGGLE SWITCH HIDDEN BUTTON or OPTIONAL CAR JACK WIRING: SWITCH Car Jack protection features See diagrams Connect to push button, toggle switch, or to a +12
Résumé du contenu de la page N° 6
WIRING – MINI PLUGS 2 - 2 - PIN PLUG (MEDIUM): PROGRAM/OVERRIDE PUSH 4 - PIN SENSOR PLUG: RED WIRE SENSOR +12V POWER * WHITE WIRE: NEG. TRIGGER 3 - PIN 1: SENSOR +12V POWER - 3 PIN PLUG (BROWN): NOT USED 6 - - Normally Open [Polarity Input for Lock relay] Normally Closed [Switch side with Rev. Polarity] Normally Open [Polarity Input for Unlock relay] DOOR UNLOC Normally Closed [Switch side with Rev. Polarity]
Résumé du contenu de la page N° 7
BLUE X BLUE X NOT USED NOT USED GREEN GREEN VIOLET/WHITE VIOLET/WHITE Y GRA X Y GRA X WHITE WHITE VIOLET VIOLET + FACTORY FACTORY L LOCK WIRE L LOCK WIRE LOCKING LOCKING UNLOCK WIRE UNLOCK WIRE YS RELA YS RELA BLUE BLUE GREEN GREEN VIOLET/WHITE VIOLET/WHITE Y GRA Y GRA WHITE WHITE VIOLET VIOLET + + + CUT UNLOCK WIRE L L CUT LOCK WIRE UL UL FUSED FUSED +12V +12V REVERSE POLARITY DOOR LOCK WIRING AFTERMARKET MOTOR DOOR LOCK WIRING UL UL FUSED +12V X = X = NEG ATIVE TRIGGER DOORLOCK WIRING
Résumé du contenu de la page N° 8
- Normally Closed Starter disable is the standard type used with most alarm systems today. This circuit will disable the Starter while the alarm is armed or has been triggered. If 12V power is removed from the system, the Battery goes dead, or the alarm is removed for service th e vehicle will start normally as if no alarm were installed. (Factory Default) Normally Open Starter Disable is a High - Security circuit that will disable the starter while the alarm is armed or trigger
Résumé du contenu de la page N° 9
The jumper plugs are located on the topside of the control module behind a small access door. To change the programmable options on this system, jumper pins must be removed or shorted. See the diagram and chart for alarm SHORTED OPEN P1 Passive Arming P2 Passi NO Passive Locks P3 - - P4* NO Autolock P5* 1 Sec. Lock/Unlock 3 Sec. Lock/Unlock P6* Single Unlock Pulse P7* Norma - P8 P9* Carjack Activation settings. Button 2 = Remote Button 2 = AUX.
Résumé du contenu de la page N° 10
JUMPER P1: PASSIVE ARMING This option controls the Passive (Automatic) Ar ming feature. If ON, arming will occur 30 Seconds after the ignition is turned off and the last door has been closed. The LED will begin flashing rapidly and the siren will chirp as a warning that the system will arm during the countdown. If a door is r eopened, the system will wait (LED solid) for the door or zone to close before arming. The unit will chirp once and flash the lights once. Doors will lock if pa
Résumé du contenu de la page N° 11
JUMPER P8: NOT USED JUMPER P9: REMOTE CARJACK FEATURE This jumper controls whether the anti - Carjack functions of the unit can be activated through the remote control’s Button #2 (Unlock). Carjack protection will activate via the remote under these 3 conditions: Jumper P9 is open (removed), Ignition is in the ON position (or driving car), and the number #2 (Unlock) button on th e remote is pressed AND HELD Turn Ignition ON, press and hold the program / override button fo
Résumé du contenu de la page N° 12
SECURWATCH® TRANSMITTER: #2 #1 LOCK/ UNLOCK/ DISARM CRIM ESTOPPER #4 #3 BUTTON 1 AUX. 1 SILENT/ AUX. 2 BUTTON 2 To arm the alarm and lock the doors, press the #1 Button on either transmitter. You will hear a single siren chirp and the lights will BUTTON 1 + 2 flash once. The system will arm, the doors will lock (optional) and = BUTTON 4 the starter will be disabled. The red in - dash LED in the vehicle will begin to flash. After a short delay of 10
Résumé du contenu de la page N° 13
If and when the alarm system is triggered, pressing the #2 button on either transmitter will reset the unit’s cycle (lig Note: AUX 1cannot be operated with the SecurWatch transmitter if the alarm system is programmed for C arjack protection. To activate an optional feature such as a trunk/hatch pop (if vehicle is properly equipped), press Button #3 (AUX) on the 4 - Button CoolGlow remote or press and hold Button #2 (when disarmed) on the SecurWatch® transmitter. This provides a ½
Résumé du contenu de la page N° 14
Use Button #4 (SLNT) f or silent arm and disarm (Chirp Defeat). Press and release Button #4 to arm/disarm without the siren chirp. The light flash will be your only confirmation on Arm/Disarm. (Buttons 1+2 w/Watch) PASSIVE ARMING / PASSIVE LOCK MODES If programmed, passive ( Automatic) Arming will occur 30 Seconds after the ignition is turned off and the last door has been closed. The lights will flash twice when the last door is closed and the LED will begin flashing rapidly whil
Résumé du contenu de la page N° 15
This feature provides Active Carjack protection through the remote control and must be enabled before use through Jumper Plug J9 programming. When the Ignition is on (vehicle is running), pr ess and hold the #2 Button (UNLOCK) for more than 2 seconds. The parking lights will flash 2 times and the LED will begin to flash rapidly to confirm the Carjack countdown sequence. 30 Seconds later, the unit will begin a Carjack Cycle consisting of 20 se conds of pre - warning chirps turning into a
Résumé du contenu de la page N° 16
POLARITY SELECT LOCK(87) CUT LOCK OUTPUT(30) LOCK SWITCH(87A) STARTER POLARITY SELECT UNLOCK(87) VIOLET UNLOCK OUTPUT(30) WHITE UNLOCK SWITCH(87A) GR VIO/WHT GREEN BLUE CS-2004WDC - + LED SWITCH SHOCK SENSOR PROGRAM DUAL-STAGE BATTERY VALET/ BATTERY RED FUSE GROUND BLACK SWITCH IGNITION + SWITCHED IGN "ON" YELLOW SENSOR 2 (-) 500MA OUTPUT LIGHTS OPTIONAL ORANGE (-) ARMED + 10A MAX WHITE NOT USED + 2A MAX PARKING BROWN SIREN BLUE (-)HOOD/TRUNK TRIGGER SWITCH GREEN (-)DOOR TRIGGER SWITCH VIOLET +
Résumé du contenu de la page N° 17
