Instruction d'utilisation Honeywell VISTA-10P

Instruction d'utilisation pour le dispositif Honeywell VISTA-10P

Dispositif: Honeywell VISTA-10P
Catégorie: Système domestique de protection
Fabricant: Honeywell
Dimension: 0.62 MB
Date d'addition: 5/26/2014
Nombre des pages: 72
Imprimez l'instruction

Téléchargez

Comment utiliser?

Notre objectif consiste à vous assurer le plus rapide accès au contenu de l'instruction d'utilisation du dispositif Honeywell VISTA-10P. En utilisant l'aperçu en ligne vous pouvez parcourir le sommaire et passer à la page où vous trouverez la résolution de votre problème avec Honeywell VISTA-10P.

Pour votre confort

Si regarder l'instruction Honeywell VISTA-10P directement sur la page n'est pas confortable pour vous, vous pouvez profiter de deux solutions possibles:

  • Exploration au mode de plein écran - pour analyser l'instruction d'une manière commode (sans l'avoir téléchargée sur votre ordinateur) vous pouvez utiliser le mode d'exploration en plein écran. Pour démarrer l'exploration de l'instruction Honeywell VISTA-10P en plein écran, utilisez le bouton Plein écran.
  • Téléchargement sur l'ordinateur - vous pouvez aussi télécharger l'instruction Honeywell VISTA-10P sur votre ordinateur et la sauvegarder dans vos ressources. Si vous n'avez pas envie de gaspiller votre espace disque, vous pouvez toujours télécharger cette instruction du ManualsBase dans l'avenir.
Honeywell VISTA-10P Manuel d'utilisation - Online PDF
Advertisement
« Page 1 of 72 »
Advertisement
Version imprimée

Beaucoup de gens préfèrent de lire les documents dans la version imprimée et non pas sur l'écran. L'option d'impression de l'instruction est aussi prévue et vous pouvez en profiter en cliquant le lien ci-dessus - Imprimez l'instruction. Il n'est pas nécessaire d'imprimer toute l'instruction Honeywell VISTA-10P - on peut choisir des pages. Economisez le papier.

Résumés

Vous trouverez ci-dessous les annonces des contenus qui se trouvent sur les pages suivantes de l'instruction de Honeywell VISTA-10P. Si vous voulez parcourir rapidement le contenu des pages suivantes de l'instruction, vous pouvez en profiter.

Résumés du contenu
Résumé du contenu de la page N° 1



ADEMCO VISTA-10P
ADEMCO VISTA-10PSIA
Security Systems




Installation and Setup Guide




















K0735V3 10/04 Rev. B

Résumé du contenu de la page N° 2

RECOMMENDATIONS FOR PROPER PROTECTION The Following Recommendations for the Location of Fire and Burglary Detection Devices Help Provide Proper Coverage for the Protected Premises. Recommendations For Smoke And Heat Detectors With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's (NFPA) Standard #72 noted below. Early warning fire detection is best achieved by the installation of fire

Résumé du contenu de la page N° 3

Table Of Contents ••••••••••••••••••••••••••••••••••• Features and Installation Highlights...............................................................................................1-1 Capabilities.............................................................................................................................................1-1 Functions.......................................................................................................................................

Résumé du contenu de la page N° 4

Table Of Contents ••••••••••••••••••••••••••••••••••• Menu Mode Programming...................................................................................................................5-1 Zone Programming Overview (∗56 and ∗58 Menu Modes)................................................................5-1 ∗56 Zone Programming Procedure......................................................................................................5-1 ∗58 Expert Programming Mode Procedures ........

Résumé du contenu de la page N° 5

SECT ION 1 Features and Installation Highlights •••••••••••••••••••••••••••••••••••• SIA Installations: The VISTA-10PSIA is a certified SIA-compliant control that meets SIA specifications for False Alarm Reduction. The VISTA-10P is not certified as SIA compliant, but can be programmed for False Alarm Reduction. To program for False Alarm Reduction, follow the SIA Guidelines noted in the applicable programming fields. Capabilities • Up to 22 zones plus eight keyfob zones (zones 49-56)

Résumé du contenu de la page N° 6

Installation and Setup Guide NOTE: All devices and accessories used in a Canadian installation must be Listed for use in Canada. Important Installation Highlights (Installer Please Read) • This system uses addressable keypads and Relay Modules (see table of addresses in Programming Overview section). • Keypads must be set for addresses 16-23 (first keypad is address 16, which is different from previous controls) and programmed in data fields *190-*196. • 4204 Relay Modules m

Résumé du contenu de la page N° 7

SECT ION 2 Mounting and Wiring the Control •••••••••••••••••••••••••••••••••••• Cabinet and Lock 1. Mount the control cabinet to a sturdy wall in a clean, dry area, which is not readily accessible to the general public, using fasteners or anchors (not supplied) with the four cabinet mounting holes. 2. Remove cabinet door, then remove the lock knockout from the door. Insert the key into the lock. 3. Position the lock in the hole, making certain that the latch will make contact with th

Résumé du contenu de la page N° 8

Installation Instructions Mounting Board with RF Receiver 1. a. Remove the receiver board from its case, then insert the top of the board into the slots at the top of the cabinet, as shown in Detail A in Figure 3. Make sure that the board rests on the correct row of tabs. b. Swing the base of the board into the mounting clips and secure it to the cabinet with the accompanying screws. c. Insert the top of the control's board into the slot in the clips and position two clips at the lowe

Résumé du contenu de la page N° 9

Mounting and Wiring the Control Wiring to Keypads 1. Connect keypads to the keypad terminals as shown on the Summary of Connections diagram. Determine wire size using the Wire Run Chart below. 2. Set keypad addresses. Refer to the address setting instructions included with the keypads and set each keypad device address according to the chart at right. 3. Program the keypad addresses and sound options in data fields *190-*196. IMPORTANT: Each keypad must be assigned a unique address, s

Résumé du contenu de la page N° 10

Installation Instructions Sounder (Bell) Connections TERMINALS ON EXTERNAL ALARM 1. Make sounder connections to alarm output CONTROL BOARD SOUNDER terminals 3 (+) and 4 (–). For supervised output, continue with steps 2 _ 4 and 3. _ 2000 ALARM 2. Cut the red Bell Supervision Jumper located OBSERVE OHM OUTPUT POLARITY EOL TERMINALS + above terminals 2 and 3 on the control board. RESISTOR + 3 3. Connect a 2k ohm resistor across the terminals of the last sounder. 2 IF BELL SUPERVISION IS E

Résumé du contenu de la page N° 11

Mounting and Wiring the Control CALIFORNIA STATE FIRE MARSHALL (CSFM) AND UL RESIDENTIAL FIRE 24-HOUR BATTERY BACKUP REQUIREMENTS The California State Fire Marshal and UL have regulations which require that all residential fire alarm control panels must be provided with a backup battery which has sufficient capacity to operate the panel and its attached peripheral devices for 24 hours in the intended standby condition, followed by at least 4 minutes in the intended fire alarm signalin

Résumé du contenu de la page N° 12

Installation Instructions Hardwire Zones Normally Open Zones/ Normally Open EOLR Zones 1. Connect open circuit devices in parallel across the loop; for EOLR zones, connect the EOLR across the loop wires at the last device. 2. Enable normally open/EOLR zones using Zone Programming mode, “Hardwire Type” prompt. Normally Closed Zones/Normally Closed EOLR Zones 1. Connect closed circuit devices in series in the high (+) side of the loop; for EOLR zones, connect the EOLR in series following

Résumé du contenu de la page N° 13

Mounting and Wiring the Control Installing the RF Receiver You can any ADEMCO 5800 Series Wireless Receivers, including: RF Receiver No. of Zones 5881L/5882L up to 8 5881M/5882M up to 16 (transmitter zone numbers = 9-24; button zone numbers = 49-56) 5883, 6150RF up to 16 (transmitter zone numbers = 9-24; button zone numbers = 49-56) 1. Set Device Address to “00” as described in its instructions (set all switches to the right, “off” position). 2. Mount the receiver, noting that the

Résumé du contenu de la page N° 14

Installation Instructions Installing the Transmitters 1. To be sure reception of the transmitter's signal at the proposed mounting location is adequate, perform a Go/No Go Test, described in the Testing the System section. 2. Install transmitters in accordance with the instructions provided with each. 3. Set 5827, 5827BD, 5804BD wireless keypads to the programmed House ID (field *24), using its DIP switches (5827) or follow the instructions provided with the device. ULC NOTE: In accorda

Résumé du contenu de la page N° 15

Mounting and Wiring the Control 5-PIN TRIGGER CONNECTOR 1345 U L A UL Listed keyswitch is required for fire installations and UL commercial and residential burglar alarm installations. If a keyswitch is used on: • an installation that transmits opening and closing 4-WIRE 4146 KEYSWITCH CABLE signals, the keyswitch zone must be programmed to (ARMED) RED send opening and closing signals. YELLOW • a UL commercial burglar alarm installation, the (READY) GREEN keyswitch’s tamper switc

Résumé du contenu de la page N° 16

Installation Instructions On-Board Triggers 5-PIN TRIGGER CONNECTOR Connect field wiring to the desired trigger pin on 1345 the 8-pin trigger connector centrally located above the terminal strip. You can use a 4-wire cable as shown. U L If on-board triggers are used, the wiring between the control unit and the UL Listed device must be run in conduit, be no more than 3 feet apart and have no intervening barriers or walls. 4-WIRE CABLE 00-trigcon-005-V3 Figure 12. On-Boa

Résumé du contenu de la page N° 17

{ { Mounting and Wiring the Control U L The 4285 and 4286 modules are UL Listed only for use on residential fire and UL residential burglar alarm installations. Phone Module Problems If no touch tones are produced following access to the security system from on-premises (this problem may arise in rare cases), it may be necessary to reverse the wires connected to terminals 3 and 4 on the phone module and the wires connected to terminals (21) & (22) on the control. The wiring diagra

Résumé du contenu de la page N° 18

Installation Instructions Audio Alarm Verification Connections (AAV, “listen-In”) Refer to the connection diagrams below. One diagram shows connections when a 4285/4286 Phone Module is used, the other shows connections when the 4285/4286 is not used. Connections use one of the on-board triggers. U UL installations using the AAV feature must use the ADEMCO UVCM module (part of the ADEMCO UVS L system) Suggested AAV Module: ADEMCO UVS (shown) or Eagle 1250 NOTES • Set field *91

Résumé du contenu de la page N° 19

SECT ION 3 Programming Overview •••••••••••••••••••••••••••••••••••• About Programming You can program the system at any time, even at the installer's premises prior to the actual installation. Programming can also be performed remotely from the installer’s office/home, using an IBM personal computer, a modem, and Compass downloading software. The following is a list of the various Programming modes used to program this system: Programming Mode… Used to … Data Field Programm

Résumé du contenu de la page N° 20

Installation Instructions Wireless Receiver, Transmitters, and Wireless Keys (keyfobs) Receiver: Set the receiver’s address to “00” using its DIP switches, then set the following options: † *22 RF Jam Option *24 RF House ID Code (if using wireless keypads) † *67 Transmitter Low Battery Report Code † These fields must be enabled for Residential † Fire, UL Residential Burglar Alarm, and UL *75 Transmitter Low battery restore report code Commercial Burglar Alarm installations. *1


Instructions pareilles
# Instruction d'utilisation Catégorie Téléchargez
1 Honeywell ADEMCO LYNXR Series Manuel d'utilisation Système domestique de protection 47
2 Honeywell ADEMCO LYNXR-EN Manuel d'utilisation Système domestique de protection 45
3 Honeywell ADEMCO VISTA VISTA-15PSIA Manuel d'utilisation Système domestique de protection 22
4 Honeywell ADEMCO VISTA VISTA-20P Manuel d'utilisation Système domestique de protection 533
5 Honeywell ADEMCO VISTA VISTA-15P Manuel d'utilisation Système domestique de protection 115
6 Honeywell EQUIPMENT MONITORING SYSTEM W8710A Manuel d'utilisation Système domestique de protection 3
7 Honeywell ADEMCO VISTA VISTA-20PSIA Manuel d'utilisation Système domestique de protection 14
8 Honeywell EKZ008200B Manuel d'utilisation Système domestique de protection 16
9 Honeywell GEH Manuel d'utilisation Système domestique de protection 1
10 Honeywell Galaxy 16 Manuel d'utilisation Système domestique de protection 30
11 Honeywell Galaxy 16 Plus Manuel d'utilisation Système domestique de protection 6
12 Honeywell GALAXY 16103 Manuel d'utilisation Système domestique de protection 4
13 Honeywell GES Manuel d'utilisation Système domestique de protection 1
14 Honeywell GEC Manuel d'utilisation Système domestique de protection 0
15 Honeywell HCD544 Manuel d'utilisation Système domestique de protection 1
16 3Com 1000BASE-T-GBIC Manuel d'utilisation Système domestique de protection 0
17 Sony BRCSDP12 Manuel d'utilisation Système domestique de protection 3
18 3Com TECHD-0000000122 Manuel d'utilisation Système domestique de protection 1
19 Sony SSC-M354 Manuel d'utilisation Système domestique de protection 3
20 Sony DIGITAL 8 DCR-TRV130E Manuel d'utilisation Système domestique de protection 9