Résumé du contenu de la page N° 1
DTV742 Installation Quick Start Guide
The Wegener Model DTV742 8VSB 4-Channel Multiplexor receives VHF/UHF broadcast HDTV signals and provides output ASI
streams for connection to cable system QAM modulators. This guide provides information for setting up and operating the DTV742.
Additional information may be found on the Wegener web site at www.wegener.com/
In addition to this guide, your box should include:
1. DTV742 8VSB 4-Channel Multiplexor
2. Power cord 3. UL safety sheet
Front and Rea
Résumé du contenu de la page N° 2
Basic System Setup Diagram Front-panel User Interface Note that from any screen, pressing the ESC key twice will return you to the Home Screen. Main-level Screens Second-level Screens Home Screen (rotates through data from each of the four RF Serial Number and Application Software Version Number inputs) Screen S/N:XXXXXX RF3 CHAN:20 8VSB SNR21.5 ErrSec:0002 VER:YYY Where XXXXXX is the unit's six-digit serial number and YYY is The channel number, modulation type (8VSB, 64QAM, or the version num
Résumé du contenu de la page N° 3
Main-level Screens Second-level Screens nd Input Setup 2 -level RF Input RF Input X Input Setup... Where X is the RF port number. Press ENT to go to the third-level Input Setup Screens below and use the 5 or 6keys to select or , adding or Press the ENT key to bring up the second-level Program removing this program to/from the output stream. Press ENT Input screen. again to confirm. Press the 4 key to go to Program Status. Press the 4 key to go to the next RF Input screen (1 through 4).
Résumé du contenu de la page N° 4
Main-level Screens Second-level Screens nd 2 -level Program Status Program Status Input Number:X Program Status... where X is the input port number. Press the ENT key to view the second-level program status screens. Press the ENT key to go to the third-level program status screen. Press the 4 key to go to Panel Help Timeout. Press the 4 key to go to the next input (1 through 4). Press the ESC key to return to the main-level Program Status Press the 3 key to go to Input Setup. screen. Press the E
Résumé du contenu de la page N° 5
Main-level Screens Second-level Screens IP Setup IP Address Selection IP Address: IP Setup... 0.0.0.0 Press the ENT key to go to IP Address Selection. Press the ENT key and then press the arrow keys to change the IP address. Press the ENT key to confirm the selection or ESC to Press the 4 key to go to Reset Unit. cancel changes. Press the 3 key to go to Panel Help Timeout. Press the 4 key to go to the Netmask Selection. Press the ESC key to go to the Home Screen. Press the ESC key to go to IP Se
Résumé du contenu de la page N° 6
Using the Web Browser – Using the web browser of your choice, set the Address to http://nnn.nnn.nnn.nnn where nnn.nnn.nnn.nnn is the IP address of the unit to be controlled. Each unit on the network must have a unique address. You should see the pages below when connected to the unit. (Be sure that your screen resolution is set to at least 1024x768 so that all items are visible. Lower resolutions will prevent you from viewing all the available tabs.) You may select which page to view by clickin
Résumé du contenu de la page N° 7
The Stream Information tab below shows input and output status. No user inputs are located on this screen. The Unit Configuration tab below shows the current configuration in use and allows storage and loading of 10 separate configurations. A configuration is the set of all user settable items (inputs and outputs) in the unit. 800057-02 Rev. A Page 7 of 11 May 24, 2003
Résumé du contenu de la page N° 8
The Config In tab below provides the interface for selecting the RF Input and Program numbers that will be used in all four of the DTV742’s multiplexors. 800057-02 Rev. A Page 8 of 11 May 24, 2003
Résumé du contenu de la page N° 9
The Config Out tabs (Config Out 1 illustrated below) provide the interface for selecting programs for each of the ASI outputs. A separate tab is used for each output (1, 2, 3, and 4). 800057-02 Rev. A Page 9 of 11 May 24, 2003
Résumé du contenu de la page N° 10
The Q&A/Help tab (shown below) provides answers to commonly asked questions about the DTV744. 800057-02 Rev. A Page 10 of 11 May 24, 2003
Résumé du contenu de la page N° 11
Notices Environmental Operating Conditions & Physical Specifications Use Indoor Altitude Up to 2000 meters o o 10 C to 40 C Temperature Range o 80% for temperatures up to 31 C decreasing linearly to 50% relative Relative Humidity (max.) o humidity as 40 C. 10.6 pounds or 4.81 kilograms Weight 3.5”x 19”x 10.5” or 88.9 mm x 482.6 mm x 266.7 mm Dimensions (H x W x D) Input Power Rating 90-132Vac & 175-264Vac, 43 Watt, 50/60 Hz Elevated Operating Ambient If equipment is installed in a closed or m
