Instruction d'utilisation Harbor Freight Tools 1/2" Compact Air Twin Hammer Impact Wrench 94802

Résumé du contenu de la page N° 1

1
/ ” COMPACT Air TWiN HAMMEr
2
iMPACT WrENCH
94802
ASSEMBLY ANd OPErATiNG
iNSTr UCTiONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PrEVENT SEriOUS iNjUr Y,
rEAd ANd UNdErSTANd ALL WArNiNGS
ANd iNSTr UCTiONS BEFOrE USE.
© ®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this manual or any
artwork contain

Résumé du contenu de la page N° 2

Specifications Maximum Torque 230 ft-lb 1 Drive Size / ” 2 1 Air Inlet / ” - 18 NPT 4 Recommended Air Pressure 90 PSI BPM 1089 Air Consumption 7 SCFM Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. Safety

Résumé du contenu de la page N° 3

9. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords and air hoses periodically and, if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times. 10. disconnect air supply. Disconnect air hose when not in use. 11. remove adjusting keys and wrenches . Check that keys and adjusting wrenches are removed from

Résumé du contenu de la page N° 4

Note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. it must be under- stood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Un

Résumé du contenu de la page N° 5

Operation (continued) Refer to FiGUrES 1 through 3 on page 6, and the Assembly Drawing on page 8. Note: Turn off your air compressor and disconnect the air hose when you are changing sockets. After you attach the socket, attach the air hose and turn the air compressor on. 4. Select the appropriate size 1/2” drive impact socket for your needs. 5. Push and snap the socket (not included) onto the Anvil (6). 6. To operate the Regulator Knob (45), follow the directions in FiGUrE 2 on

Résumé du contenu de la page N° 6

Maintenance 1. Make sure your Impact Wrench is disconnected from the air hose before attempting any maintenance. 2. Wipe the Impact Wrench down with a lint free cloth after each use. 3. Make sure the Anvil (6) is clear of dirt or debris. If possible, spray it with compressed air before each use. 4. If you do not use an inline oiler/filter system, lubricate the tool daily by holding it so that the Air Inlet (31) is facing up. Squeeze the Trigger (20), and place one or two drops of oil

Résumé du contenu de la page N° 7

Parts List item description Qty. item description Qty. 1 Hammer Case 1 24 Rear Rotor Bearing Retainer 1 2 Grease Fitting 1 25 Reverse Valve Bushing 1 3 Hammer Case Bushing 1 26 Valve Seat 1 4 Socket Retainer 1 27 Throttle Valve 1 5 O-ring 8X1.8 1 28 Spring 1 6 Standard Anvil 1 29 O-ring 14X3 1 7 Hammer Pin 2 30 O-ring 1 8 Hammer 2 31 Air Inlet 1 9 Hammer Frame 1 32 Bust Screw 1 10 End Plate Gasket 1 33 Band 1 11 Housing 1 34 Screen 1 12 Rear Rotor Bearing 1 35 Cover 1 13 Front End Plate 1 36

Résumé du contenu de la page N° 8

Assembly diagram and Warranty LIMITED 1 YEAR WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase. This warranty does not apply to damage due directly or indirectly to misuse, abuse, negligence or accidents; repairs or alterations outside our facilities; or to lack of