Résumé du contenu de la page N° 1
User’s Manual
VoIP FXO Gateway
Model No.: SP5052A/S, SP5054A/S
http://www.micronet.info
Résumé du contenu de la page N° 2
Table of Contents 1. WEB CONFIGURATION ............................................................................................. 3 STEP 1. USE WEB BROSWER TO CONNECT GATEWAY..................................................... 3 STEP 2. INPUT THE LOGIN NAME AND PASSWORD............................................................. 3 STEP 3. START TO CONFIGURE....................................................................................... 4 1.1 NETWORK INTERFACE...............
Résumé du contenu de la page N° 3
2.13 [LINE].................................................................................................................. 34 2.14 [ROUTE] .............................................................................................................. 35 2.15 [PREFIX].............................................................................................................. 37 2.16 [PAUSE]......................................................................................................
Résumé du contenu de la page N° 4
1. Web configuration The initial version for HTTPD web management interface provides user to configure easily rather than command operating method through RS-232 / TELNET. The configuration function and step is similar with the way through command line. Basically this version is not the finalized version for web interface. Please refer to the manual for more information. Below provide a simple user guide for user to configure via web interface. Next version for HTTPD web management
Résumé du contenu de la page N° 5
Step 3. Start to Configure Most of all commands displayed in console / telnet are transfer to web interface. The most important commands are Network Interface, SIP Config and Reboot System. The method is as the same as command mode. 1.1 Network Interface Users have to configure the Network configurations in this page. This gateway will be work while it is connecting with the internet network. Please get more info from the following descriptions. (See figure 3.1) 4
Résumé du contenu de la page N° 6
Parameter Description: IP Address: Define the ip address for your networking if it is the fixed ip. Please get this info from your ISP. Subnet Mask: Define the mask address for your networking. Please get this info from your ISP. Default Routing Gateway: Define the default gateway for your networking. Please get this info from your ISP. IP Mode: To configure the fixed or dynamic ip address for this unit. Please configure to PPPoE if the ADSL is using the PPPoE type. HTTP Port: To
Résumé du contenu de la page N° 7
connection. PPPoE IP Address: In the PPPoE mode, this table will show the ip address that this unit gets from the ISP. PPPoE Destination: In the PPPoE mode, this table will show the default gateway address that this unit gets from the ISP. PPPoE DNS primary: In the PPPoE mode, this table will show the DNS ip address that this unit gets from the ISP. After Remote Host Disconnection: This unit will reboot and re-connect to the ISP 1.2 SIP Config This WEB page will help user to c
Résumé du contenu de la page N° 8
Peer-2-Peer: It only supports the peer-to-peer mode and users have to define the phone book for this mode. Proxy: Users have to register on the Proxy if users picked up this option. Gateway: Only user line1 has to register on the Proxy, then the line1, line2, line3 and line4 join in the same hunting group automatically. Primary Proxy IP Address: Enter the proxy ip if users pick up the proxy mode. Primary Proxy port: Set Proxy port for SP5050 series to send message, default value i
Résumé du contenu de la page N° 9
1.3 Security Config Some proxy will include the security policy. The endpoint may need the user account and password for the registration. If these are necessary, users could put the correct account and password in the correct table. Parameter Description: Line 1 Account: The user name for the line 1 account. Line 1 Password: The password for the line 1 account. Line 2 Account: The user name for the line 2 account. Line 2 Password: The password for the line 2 account. Line 3
Résumé du contenu de la page N° 10
Parameter Description: Type: Show the type of this port. There are only one types of this gateway. (SP5052A/S / SP5054A/S will show the FXS and FXO type. It can not be changed.) Hunting Group: Define the group number of this port. When the port is busy, the call could be transferred to another port in the same group. Hotline: Enable or Disable the hotline mode. The hotline mode will be enabled if you enter the hotline number. The default setting is disabled. Fwd. Type: Forward t
Résumé du contenu de la page N° 11
Parameter Description: Keypad Type: Select different DTMF Keypad Type In-Band: The DTMF signal sending by RTP. RFC2833: RTP Payload for DTMF Digits INFO: The DTMF signal sending by SIP INFO. Inter Digit Time: Set the DTMF inter-digit time (second). Parameter defines the maximum amount of time between digits. If a digit is not followed by another within this time limit, then digit collection is terminated. Ring Time: It for the ring detection from the PSTN. The ring detection w
Résumé du contenu de la page N° 12
Parameter Description: Codec Priority: This could help users configure the codec priority for using. Frame Size: To configure the packet size for the codec that users want. G.723 Silence Suppression: To enable the VAD and CNG function for the G.723 codec. Volume: Adjust the volume in “Voice” (sending out); “Input” (receiving); “ DTMF” (DTMF sending out). Please Noted the value is limited. Echo Cancel: To enable or disable the echo cancellation function. Jitter Buffer: TO confi
Résumé du contenu de la page N° 13
define the pattern of the disconnect tone if the disconnect tone from PSTN side is not the standard tone. Parameter Description: Disconnect Tone 1 – 4: To configure the frequency, level gain and on/off time for the busy tone from PSTN or PABX side. The busy tone supports 4 tables. Remote Ring Back Tone: To configure the frequency, level gain and on/off time for the ring tone from PSTN side. The gateway won’t connect the calls if the ring tone value is incorrect. 1.8 Phone B
Résumé du contenu de la page N° 14
Parameter Description: Index: The list number of the Phone Book. Name: The name for this contact number. E164: The dialing number for the calling side. IP Address: The destination IP address for this phone number. Port: The call signal port of the destination. Drop: Support the drop function. Enable is for enable this drop function; Disable is for disable this drop function. The Drop Prefix will drop the E164 number, which you had configured in the E164 table. Insert: Support t
Résumé du contenu de la page N° 15
1.9 Prefix Configuration The Prefix function is using the drop and inserts function. Parameter Description: Index: The list number of the Phone Book Prefix: The prefix number of the whole numbers that could be into this gateway Drop: The drop function. Enable this function by the Enable button; Disable this function by the Disable button Insert: The insert function. Users could enter the digits that you want to insert in this number Add Data: Press this button if users fill the
Résumé du contenu de la page N° 16
1. Press the Prefix Configuration button to enter the configuration table. 2. Enter the index number. Put the prefix numbers you will dial in the prefix table, enable (disable) the drop function and enter the numbers you want to insert. The usage is as same as the drop, insert function of the Phone Book. Input (Prefix) Drop Insert Output 100 Disable X 100 200 Disable 0 0200 300 Enable X X 400 Enable 500 500 3. Press the Prefix Configuration button to reload the configuration
Résumé du contenu de la page N° 17
4. Please Commit it and Reboot the system if the configuration is finished. 1.10 Routing Table Parameter Description: Index: Define the number of this data. Prefix: Define the number you dial. You could just define the first 16
Résumé du contenu de la page N° 18
digit of the numbers Destination: Define the destination of this rule. There are three directions of the destination. E164: Define a right E164 number of the destination you want. Min Digits: The minima digits you dial. Max Digits: The maxima digits you dial. Hunt Method – Enable the Hunt Group function and pick up the hunt type. None – Disable this function Group – The call will search other ports to be the destination with the same group if the origin destination is busy. Al
Résumé du contenu de la page N° 19
1.11 FXO Password You will get the IVR if you make calls from PSTN side. The IVR will ask you the password you set, and you could make other calls to IP side if the password you type is correct. Please press the FXO Password button to configure the password Note: This function is only for the calls from the PSTN side. It’s not ready for the IP side as so far. 1.12 IP Packet ToS The Type of Service needs worked with the network router supported. The router will check al
Résumé du contenu de la page N° 20
these values to make the packets with the correct values for the TOS service from the gateway. According to the RFC 1349 document, the TOS value as following: 1000 – minimize delay 0100 – maximize throughput 0010 – maximize reliability 0001 – minimize monetary cost 0000 – normal service These values are the Binary format. Please change to the Decimal and put these values in to the correct table. 1.13 Password There are two accounts for login to access or change the configu
