Résumé du contenu de la page N° 1
Hydrostatic Zero-Turn
Commercial Riding Mower
Professional Turf Equipment
60” Fabricated Deck
W/ R.O.P.S.
OPERATOR’S AND SERVICE MANUAL
Résumé du contenu de la page N° 2
TABLE OF CONTENTS Foreword. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 General Safety Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 A.Danger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Résumé du contenu de la page N° 3
FORWARD The Tank Hydrostatic Zero-Turn Commercial Riding Mower provides superb maneuverability, mid-mount cutting capability for professional landscapers, commercial lawn service compa- nies, professional turf managers and golf course superintendents. The machine incorporates many safety features that should be studied by all operators and maintenance personnel before use. The list of safety precautions should receive particular attention. This manual presents all of the operating and mainten
Résumé du contenu de la page N° 4
6. Do not check for hydraulic leaks with any part GENERAL SAFETY of the body. OPERATIONS 7. Do not add fuel to a machine when the engine is running and/or the exhaust system is hot. A. DANGER 8. Keep machine clean and free of debris, grass, 1. Do not operate machine in confined areas leaves, oil, grease, etc. where exhaust gases can accumulate. 9. Place lap bars in neutral/start position, set 2. Do not operate machine without mower chute park brake, disengage P.T.O., turn engine off, defl
Résumé du contenu de la page N° 5
11. When looking for oil leaks, never run your and battery surfaces kept clean of acids and corro- hand over hydraulic hoses, lines or fittings. sion. If batteries are re-charged or “jumped” from Never tighten or adjust hydraulic hoses, lines external sources, make sure that the connections are or fittings while the system is under pressure. made properly and in the correct sequence...connect If high-pressure oil penetrates the skin, the oil to the positive terminal of the good battery first
Résumé du contenu de la page N° 6
blade bolts are tight before restarting the 8. The ROPS will not prevent the machine from engine. upsets or roll overs. 13. Never leave the mower unattended without: 9. Only approved attachments should be used turning off the blade clutch switch; placing the on this machine. left and right steering levers in the neutral opened-out position; moving the throttle to slow; setting the parking brake; shutting off the engine and taking the key from the ignition switch. 14. Never walk or stand on
Résumé du contenu de la page N° 7
SAFETY DECALS AND LABELS TO REDUCE THE RISK OF INJURY, DO NO T O P E R A T E M O W E R UN L E S S DISCHA RG E CHU TE C O VER OR GRASS C A T C H E R IS IN I T S PR O PER P LA C E . WARNING DAN GER K EE P HA ND S an d FE ET AW AY SHIELD MISSING DO NOT OPERATE Part Number: 00030635 Part Number: 01002166 DANGER ROTATING BLADE Do not put hands or feet under or into mower when engine is running. Part Number: 00030633 Part Number: 01003452 Part Number: 01003451 Part Number: 01003859 ! WARNING En
Résumé du contenu de la page N° 8
SPECIFICATIONS GENERAL INFO. Controls: Engine ignition and start switch; throttle; choke; left and right steering levers; electric blade clutch switch; parking brake; mower deck lift Parking Brake: Mechanical linkage brake handle to internal drum brakes Seat: Adjustable seat and armrests. 5" Adjustment (fore-aft) Frame: 2" Steel structural tube and plate, all welded construction Instrumentation: Hour meter, Tachometer, Maintenance-minder Front Caster Wheels: 13 x 6.50 x 6 Drive Wheels: 24x12 -
Résumé du contenu de la page N° 9
OPERATING INSTRUCTIONS Figure. 1 Figure. 2 Tach and Electric Blade Engine throttle Hour Meter Clutch Switch Choke Lever Ignition Switch maintain the uphill side lap bar “essen- A.General tially” in a fixed position. 1. When Mowing: k. Be careful when crossing gravel paths or a. Keep adults, children, and pets away from roadways. Always turn off the blade clutch the area to be mowed. switch and wait until the blades stop rotat- b. When operating this mower, in the forward ing and raise the cu
Résumé du contenu de la page N° 10
b. Avoid turning downhill if possible, if not use B.Controls extra care and go slowly. 1. Engine Ignition and Start Switch: (See Fig- c. Avoid turning when going downhill, traction ure 1.) Located on the instrument housing is at a minimum going downhill. below the right side of the operator’s seat. d. Do not operate with discharge side of the When the key is inserted and turned clock- mower toward streets, buildings, play- wise, 45 degrees, the ignition circuit is closed. grounds, parking
Résumé du contenu de la page N° 11
Steering Levers Deck Lift Handle Note: The 19hp and 23hp use the 5 Brake gallon fuel tank. Figure. 4 Fuel Shutoff Valve Figure. 3 pedal assembly. Fold the pedal up to vertical 4. Electric Blade Clutch Switch: (See Figure position so the hole in the pedal aligns with 1.) Located on the right side of the mower the hole in the lever. Reinstall the detent pin. beside the ignition switch. This is an “on/off” This is the required position for the foot pedal push pull switch that controls the
Résumé du contenu de la page N° 12
the procedures below to set the appropriate C.Initial Adjustments angle to the mowing deck. 1. Check the fluid levels and tires: a. Park the mower on a flat paved surface, engage the parking brake, shut off the Note: These checks should be made daily, engine, remove the key from the ignition before starting the engine. switch, remove connection of the spark a. Fuel: Using a good grade of unleaded, plugs and using the transport lever, lower regular gasoline (for a gasoline engine), fill
Résumé du contenu de la page N° 13
f. Raise the mowing deck to the transport 3. That there are no loose or missing hard- position using the transport lever. ware nor any missing items. g. Use the transport lever to lower the mow- 4. That no non-approved devices are ing deck to the cutting position and repeat installed. step “b.” above to make sure that the 5. That all safety signs and decals are desired cutting height has been attained. If properly installed and legible. the dimensions are not correct, repeat e. This is a one p
Résumé du contenu de la page N° 14
3. Move both lap bars out of the neutral/ 4. To turn, retard one lap bar ahead of the start position to the neutral position other and the machine will turn toward (toward center of machine). Slowly, the same side that was retarded — I.E., move both lap bars toward the front of to turn counter-clockwise (to the LEFT), the machine until the machine begins to move the LEFT lap bar rearward more move forward — release the lap bars than the right side, and to turn clockwise and the machine sho
Résumé du contenu de la page N° 15
k. Practice mowing in straight passes. When Note: Do not hold the key in the “Start” you feel confident, slowly practice mowing position for more than 10 seconds or you may damage the starter. If the engine does not start around obstacles such as trees. in this time, wait about 30 seconds and try 5. Parking the Mower: again. a. Push off the electric blade clutch switch. i. Gasoline Engine: Once the engine starts, b. Use the Deck Lift Handle to raise the mow- push the choke on halfway and a
Résumé du contenu de la page N° 16
Linch Pins Linch Pins Figure. 6 Height of Cut Clevis Pin g. Shift the deck toward the ignition switch MAINTENANCE AND side of the mower and remove. h. To install reverse the process. SERVICE 2. Changing a Blade: a. Remove the Key from the ignition and dis- WARNING: connect the spark plug. Disconnect the spark plug wires or remove the b. Jack up the front of the mowing deck about key from the ignition to prevent the engine one foot and block it in that position. from accidentally starting bef
Résumé du contenu de la page N° 17
a. Set the parking brake. b. Clean any debris from the blades. Keep blades sharp and free of build up at all Cover times. Plate c. Sharpen blades evenly at the original 30° Spindle angle to maintain balanced cutting blades. Do not sharpen the underside of the blades. Use a electric blade sharpener, a conventional electric grinder or a hand file to sharpen the blades. d. Replace any blade with severe nicks or dents that cannot be removed by filing. e. Check the balance of the blade after
Résumé du contenu de la page N° 18
caps and drain oil from both left and right pumps. Replace and retighten nuts. Hydraulic pumps Figure. 9 Figure. 8 Hydraulic Tank Unfasten hose and drain from 1. Adding Hydraulic Oil (use SAE14W 40) this side of both pumps. a. Place the Mower on a level surface and engage the parking brake. j. Coat new filter seal with oil before installa- b. Stop the engine and remove the key tion. Install new hydraulic oil filter filled with from the ignition switch. new oil. c. Clean the area around th
Résumé du contenu de la page N° 19
c. Store the battery with a full charge. A dis- other electrical components. This is a stan- charged battery will freeze (refer to the dard plug-in type automotive fuse rated at 7.5 table below). amp. 7. Safety Switches: There are five safety switches in the electrical circuit which control Specific Gravity Freezing Temp (°F) the engine. They are (1) the blade clutch switch, (2) the parking brake switch, (3) the 1.265 -71 left and (4) the right steering lever switches and (5) the seat swit
Résumé du contenu de la page N° 20
occurs. Engage the BBC (PTO Clutch) a does not stop, the seat switch must be couple of times, and re-check the air-gap. replaced. With both steering levers folded If it is not between the specs listed on page out in the neutral position, the parking 24, repeat the adjustment procedure. brake engaged and the blade clutch switch b. Parking Brake Switch: Sit in the opera- in the “off” position, sit in the operator’s tor’s seat. With both steering levers seat and start the engine. Turn the blad
