Résumé du contenu de la page N° 1
PVS-15
Personal Viewing System
Assembly and Operation Manual
Cardio Theater Holdings, Inc.
21420-D NW Nicholas Court #12-13
Hillsboro, OR 97124
(800) 776-6695
(503) 645-8881
www.cardiotheater.com
Résumé du contenu de la page N° 2
TABLE OF CONTENTS Parts List…………………………………...Page 2 Stand Assembly………………..………… Page 3-4 DVD Player Assembly………..…………..Page 5-7 LCD Screen Assembly………………..….Page 8-9 Mounting Screen Controller…………..….Page 10 Programming TV Channels………….…..Page 11 Cable Management……………………….Page 12 RF Distribution…………………………….Page 13 Specifications…………………………….. Page 14 Warranty……………………………………Page 15 Technical Support…………………………Page 16
Résumé du contenu de la page N° 3
Parts List: Master Set Up Package 1 Master IR Remote Control 1 Operations Manual Screen Controllers (1 for each Screen) 1 Neoprene Mounting Pad (1 for each controller) 1 DVD Player Master IR Remote (Optional) Screen Box 1 15 inch LCD Screen 1 AC Adapter 1 Adapter Power Cord 1 LCD Back Cover 1 Controller Cable 1 LCD Screen Hardware Package 4 Wire Ties Stand Box 2 Stand Feet 1 Base Cross Bar 1 Lower Vertical Tube 1 Upper Vertical Tube (S
Résumé du contenu de la page N° 4
Stand Assembly Step 1 Step 2 Determine width of stand feet in relation to the Insert lower vertical tube over center stub cardio equipment. Use a 7/16 wrench to secure and hand install one 3/16 Allen head screw a 2 hex screws per leg. few turns into vertical tube. Do not tighten at this time. (Clearance needed for Wires) Step 4 Step 3 Insert upper curved tube into lower tube. Do Insert plastic base cover over lower vertical not install bolts until step 5 is
Résumé du contenu de la page N° 5
Stand assembly- continued Step 7 Step 8 Route coax and AC power plug to center With cables properly placed in cover slot, secure Opening of base cover and make sure to tighten lower base cover with 2 Allen head screws provided. bolt before installing cover. Step 9 Install last remaining Screw in upper tube Assembly and double-check all Fasteners for Tightness. 4
Résumé du contenu de la page N° 6
DVD Player Assembly NOTE: Skip to Page 7 if not installing DVD Player Important: There are two models of DVD brackets. Short DVD Bracket Long DVD Bracket For S Model Stand For L Model Stand 1: Run supplied Audio Video cable and DVD 12 Volt Power cable from opening at top of stand out through large round hole in upper tube of stand. 5
Résumé du contenu de la page N° 7
2: Pull Audio/Video and 12 Volt Power cable wires through hole in DVD bracket and attach bracket to stand with 2 hex screws provided. IMPORTANT: When attaching Short Version, confirm that the large square opening on the rear of the bracket is positioned on the right side of the stand tube as shown. Short Version Long Version 3: Plug Audio Video cable into the Video & Audio “Outpu
Résumé du contenu de la page N° 8
6: Connect DVD 12 Volt Power cable to main Coax / Power wire coming through top of stand. 7: Connect the Video cable coming from the DVD player “Output” to the connector labeled “Video Y” on the back of the monitor and the cable going from the DVD players audio outputs to “Audio Left & Right” input on the back of the monitor. 7
Résumé du contenu de la page N° 9
LCD Screen Assembly 1. Attach pivot assembly to back of LCD monitor using upper two mounting holes as shown in figure 1. Leave out the lower two mounting screws until after all wiring is installed onto back of monitor. 2. Install monitor assembly onto upper stand tube using (3) M4 X 10mm socket head cap screws as shown in Figure 2 3. Install power connector from harness that was installed into stand assembly earlier, to input on back of
Résumé du contenu de la page N° 10
LCD Screen Assembly (continued) 5. Remove slip-on antenna connector from monitor by pulling straight down on connection (Figure 5). Screw slip-on connector onto coax cable and then push assembly back into the monitor’s antenna connector. (Figure 6) 6. Attach Back Cover plate using 2 M4 x 10mm black screws. (Figure 7) Note: Before securing back cover, confirm that all cables connected to LCD screen have sufficient slack for tilting the monitor and are not
Résumé du contenu de la page N° 11
Mounting Screen Controller CNTE-4 CNTE-16 1. Remove backing from neoprene mounting pad and place either vertically or horizontally around equipment handrail as appropriate as shown below. 2. Insert two nylon wire ties (provided) through the bottom holes in the mounting bracket on the rear of the Screen Controller. 3. Attach wire ties as tightly
Résumé du contenu de la page N° 12
Auto Programming TV Channels The following requires the LCD Screen Master IR Remote Control Unit 1. Press menu button on Master IR Remote. 2. Scroll Down to “Install” then press “Select”. 3. Select “Auto Search” and press “Select”. 4. Select Cable, HRC or Air (Check local cable company for HRC) 5. Note: Programming may take up to 3 minutes. Manually Add or Erase Channels: 1. Manually
Résumé du contenu de la page N° 13
Cable Management System The Optional Cable Management System is used to cover the antenna cable and power cords that run between the individual stands. It consists of a metal bracket that connects to the bottom of the monitor stand and a plastic two-channel extrusion that can be cut to length with common hand tools. 5 foot Cable Management extrusion. Cable Management Bottom view of bracket Mounting bracket mounted with four screws
Résumé du contenu de la page N° 14
RF Distribution Below is a diagram of a typical install. Please note that the tap values are dependant on having a 35 db signal at the output of the signal amplifier. It is best to use a quality amplifier that has a variable output so that you can adjust it to match 35 db even if your input is either lower or higher. These tap values and db readings are based on RF theory. 13
Résumé du contenu de la page N° 15
Specifications: 15” Color LCD Monitor Visible Screen Size 304.1(H) X 228.1(V) Pixel Range 0.297(H) X 0.297(V) Type a-si TFT Liquid Crystal Display Visual Angle upper 55’/lower 65’, left 70’/right 70’ Horizontal Frequency 31~60 KHz(Auto Set) Vertical Frequency 56~75 Hz(Auto Set) Display Color 16.2M Color Input/Video Signal Analog 0.714Vp_p Positive(75ohm) TV Color System PAL,SECAM,NTSC Channel Memory 100 Channel—PAL System Receiving Channel 181Ch (113ch
Résumé du contenu de la page N° 16
Warranty Cardio Theater™ warrants the Personal Viewing System to be free from defects in material and workmanship for the following period of time from date of shipment, provided that the products have not been subject to mechanical, electrical, or other abuse or modifications. Cardio Theater LCD Screen 1 Years Parts & Labor Cardio Theater Screen Controller 1 Year Parts & Labor Quick Change Headphone Jack 90 Days (from original installation) Should the LCD Screen,
Résumé du contenu de la page N° 17
Technical Support Technical Support Numbers Telephone 1-800-776-6695 Technical Support Hours: 6:00 AM to 5:00 PM Monday through Friday PST. Write To: Cardio Theater Holdings, Inc. 21420-D NW Nicholas Court #12-13 Hillsboro, OR 97124 Notice Due to continuing advancements in technology, Cardio Theater Holdings, Inc. reserves the right to make changes in hardware, packaging, and any accompanying documentation without prior written notice. Cardio Theater
Résumé du contenu de la page N° 18
17
