Instruction d'utilisation Rosewill RC-100

Résumé du contenu de la page N° 1

USB 2.0 2-Port PCI Adapter RC100
User Manual

Résumé du contenu de la page N° 2

USB 2.0 2-Port PCI Adapter RC100 User Manual System Requirements • Windows® 98SE, 2000, ME, XP(Pentium® or K6® - class processor -266 MHz or higher) • Mac® OS 10.1 or Above • 32MB of RAM • Available PCI Slot • CD-ROM Drive(for driver installation) Specifications • VIA VT6212L chipset • USB 1.1 and 2.0 Compliant • Up to 480 Mbps (Megabits-Per-Second) Data Transfer Rate • 40 Times Faster Than The USB 1.1 • Hot Swappable Plug-n-Play • 2 External Type A USB 2.0 Ports • 2 Type A USB 2.0 Ports by co

Résumé du contenu de la page N° 3

USB 2.0 2-Port PCI Adapter RC100 User Manual Pin No. Definition 1 Power 2 Power 3 USB3 D- 4 USB4 D- 5 USB3 D+ 6 USB4 D+ 7 GND 8 GND 9 No Pin 10 NC 1. Remove your computer’s cover. (Note: If necessary, consult your computer’s manual for help in removing the cover) 2. Locate an available PCI slot and, if necessary, remove the expansion slot bracket. 3. Insert the USB 2.0 Card gently but firmly until the card is fully seated. 4. Fasten card to the computer case using a screw.

Résumé du contenu de la page N° 4

USB 2.0 2-Port PCI Adapter RC100 User Manual Controller” driver search program. Click “Next”. 2. Select “Search for the best driver for your device”. Click “Next”. 3. Don’t select any location and click “Next”. 4. Select “The updated driver (Recommended) VIA Tech 3038 PCI to USB Universal Host Controller”. Click “Next”. 3

Résumé du contenu de la page N° 5

USB 2.0 2-Port PCI Adapter RC100 User Manual 5. Click “Next” again to confirm the driver and begin installation. Please insert the disk labeled “Windows 98 CD disk”. 6. After driver installation finished, click “Finish”. 7. Next, you will see Windows find a “VIA Tech 3038 PCI to USB Universal Controller” device again. Repeat the above process for the second “VIA Tech 3038 PCI to USB Universal Controller”. 8. As “PCI Universal Serial Bus” driver search program shows up, as Figure 5. Click “Can

Résumé du contenu de la page N° 6

USB 2.0 2-Port PCI Adapter RC100 User Manual 10. Once you have rebooted, your USB 2.0 Four Port PCI Card is ready to be used. If you open the Device Manager, you will see the newly installed devices. To locate the Device Manager right click “My Computer” and select “Properties”, then the “Device Manager” tab. Windows® ME Installation 1. Windows will detect the USB 2.0 Four Port PCI Card and automatically install drivers for all known USB devices. Follow the installation to restart the

Résumé du contenu de la page N° 7

USB 2.0 2-Port PCI Adapter RC100 User Manual 2. After you have rebooted, Please insert the Driver CD into the CD-ROM drive of your computer. Browse to the VIA USB 2.0 Driver Folder “\PCI_IO\Viausb20” on the Driver CD, then double-click the installation file “Setup.exe”. Follow the on-screen instructions, then reboot when prompted. This will automatically install the driver for the “PCI Universal Serial Bus” device found in step 1. 3. Once you have rebooted, your USB 2.0 Four Port PCI Card is

Résumé du contenu de la page N° 8

USB 2.0 2-Port PCI Adapter RC100 User Manual Windows® XP Installation Windows® XP operating system natively supports this USB 2.0 Four Port PCI Card. • No Drivers are necessary However, please ensure you have the latest Service Pack installed. • Windows® XP Service Pack 1 or later When you start the PC, the drivers are installed automatically by the Hardware Wizard. Thank you for purchasing Rosewill Product. Please register your product at www.rosewill.com for complete warranty information an