Instruction d'utilisation Transition Networks SWITCHABLE ETHERNET AND FAST ETHERNET SSEFE10XX-10X

Résumé du contenu de la page N° 1

User’s Guide
SSEFE10xx-10x
Stand-Alone Media Converter
• Switchable Ethernet and Fast Ethernet
 10 Mb/s Copper to Fiber
 100 Mb/s Copper to Fiber
Transition Networks SSEFE10xx-10x series
Ethernet / Fast Ethernet media converter is a
10Mbps or 100Mbps switch-selectable media
converter. Both the copper and fiber links operate at the same speed setting via a
hard set with a dip switch, so the media converter operates at either 10 Mb/s
copper to fiber or 100 Mb/s copper to fiber.
Part Number Po

Résumé du contenu de la page N° 2

SSEFE10xx-10x Installation Installation -- Continued The Link Pass-Through and speed switches are located on the side of the Power the Media Converter media converter. Use a small screwdriver to set the recessed switches. AC 1. Connect the barrel connector on the power adapter to the media Link Pass-Through: up = Enable Set Link Pass-Through (switch 1) converter’s power port (located on the back of the media converter). Speed: up = 100 Mb/s Switch 1 sets the Link Pass-Through feature: 2. C

Résumé du contenu de la page N° 3

SSEFE10xx-10x Installation -- Continued Operation Install the Fiber Cable Status LEDs The SSEFE10xx-10x is designed to be installed in pairs over the fiber link, Use the status LEDs to monitor the SSEFE10xx-10x media converter operation in where one is the local media converter and the other is the remote. the network. 1. Locate or build fiber-optic cable with male, two-stranded TX to RX PWR Power On = Connection to the external AC or DC power. connectors installed at both ends. F-ACT Fiber

Résumé du contenu de la page N° 4

SSEFE10xx-10x Cable Specifications Cable Specifications -- Continued The physical characteristics must meet or exceed IEEE 802.3™ specifications. Copper Cable Fiber Cable Category 3: (Minimum requirement for 10 Mb/s operation) Gauge 24 to 22 AWG -9 Bit Error Rate: <10 Attenuation 11.5 dB/100m @ 5-10 MHz Single mode: 9 µm Category 5: (Minimum requirement for 100 Mb/s operation) Gauge 24 to 22 AWG SSEFE1012-100 1310 nm single mode Attenuation 22.0 dB /100m @ 100 MHz Fiber-optic Transmitter

Résumé du contenu de la page N° 5

SSEFE10xx-10x Technical Specifications Troubleshooting For use with Transition Networks Model SSEFE10xx-10x or equivalent. 1. Is the PWR LED on the media converter illuminated? Standards: IEEE 802.3™, 10Base-T, 100Base-TX, 100Base-FX NO Data Rate: 10 Mb/s, 100 Mb/s  Ensure that the power adapter is the proper type of voltage and cycle frequency for the outlet (See “Power Supply” on page 8.) Dimensions 3.25" x 4.7" x 1.0" (83 mm x 119 mm x 25 mm)  Ensure the power adapter is properly installe

Résumé du contenu de la page N° 6

SSEFE10xx-10x Troubleshooting -- Continued Contact Us Technical Support 6. Is the TP-ACT LED illuminated? Technical support is available 24 hours a day. US and Canada: 1-800-260-1312 NO  Check the twisted-pair copper cables for proper connection. International: 00-1-952-941-7600  Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600. YES Transition Now  Go to step 7. Chat live via the Web with Transition Networks Technical Support. Log onto www.transition.com and click the Transitio

Résumé du contenu de la page N° 7

Compliance Information CISPR22/EN55022 Class A + EN55024 CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructi