Instruction d'utilisation American Standard 2175.503

Résumé du contenu de la page N° 1

Installation
Instructions
COLONY SOFT
2175.503
Single Control Lavatory Faucet
with Speed Connect™ Drain
Congratulations on purchasing your American Standard faucet with the
Speed Connect drain, a feature found only on American Standard faucets.
Speed Connect Drain*
• 1/3 of the parts, installs in 1/3 of the time
Certified to comply with ANSI A112.18.1
• No tools needed
M968882 Rev. 1.3
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*Your new American St

Résumé du contenu de la page N° 2

INSTALL POP-UP DRAIN 2 Fig. A. Fig. B. REAR OF SINK Remove CLEAR PLASTIC COVER (1). Remove 1 CARDBOARD SPACER (2) from under DRAIN POP-UP (3). Fig. A. 4 3 Drop DRAIN BODY (4) through sink drain 6 hole. Make sure WHITE FOAM GASKET (5) 5 is under flange of DRAIN BODY (4). Fig. B. SINK Note: No plumber’s putty or caulk is required. 2 DRAIN HOLE The CABLE ATTACHMENT POINT (6) must face towards the rear of the SINK. Fig. B. INSTALL BLACK GASKET 3 Install BLACK CONE GASKET (1) onto DRAIN BODY (2) fro

Résumé du contenu de la page N° 3

ATTACH CABLE CONNECTOR 6 Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and 1 hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 1-1/4” O.D. 2 CHECK OPERATION OF POP-UP 7 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. 1 Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. 2 MAKE WATER SUP

Résumé du contenu de la page N° 4

TEST INSTALLED FITTING 9 5 1 With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Ensure that AERATOR (3) is tightened completely. Operate HANDLE (1) to to alow water flow. 3 CHECK DRAIN CONNECTIONS 10 4 Operate POP-UP KNOB (5) and fill Sink with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Sink. If STOPPER (4) does not seal properly, please refer to “Troubleshooting Guide” in these instructions. Release POP-UP KNOB (5) dow

Résumé du contenu de la page N° 5

Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode. C

Résumé du contenu de la page N° 6

STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate LOGO Stopper s