Instruction d'utilisation EMC CX700

Instruction d'utilisation pour le dispositif EMC CX700

Dispositif: EMC CX700
Catégorie: Supports portables de données
Fabricant: EMC
Dimension: 1.13 MB
Date d'addition: 12/27/2013
Nombre des pages: 36
Imprimez l'instruction

Téléchargez

Comment utiliser?

Notre objectif consiste à vous assurer le plus rapide accès au contenu de l'instruction d'utilisation du dispositif EMC CX700. En utilisant l'aperçu en ligne vous pouvez parcourir le sommaire et passer à la page où vous trouverez la résolution de votre problème avec EMC CX700.

Pour votre confort

Si regarder l'instruction EMC CX700 directement sur la page n'est pas confortable pour vous, vous pouvez profiter de deux solutions possibles:

  • Exploration au mode de plein écran - pour analyser l'instruction d'une manière commode (sans l'avoir téléchargée sur votre ordinateur) vous pouvez utiliser le mode d'exploration en plein écran. Pour démarrer l'exploration de l'instruction EMC CX700 en plein écran, utilisez le bouton Plein écran.
  • Téléchargement sur l'ordinateur - vous pouvez aussi télécharger l'instruction EMC CX700 sur votre ordinateur et la sauvegarder dans vos ressources. Si vous n'avez pas envie de gaspiller votre espace disque, vous pouvez toujours télécharger cette instruction du ManualsBase dans l'avenir.
EMC CX700 Manuel d'utilisation - Online PDF
Advertisement
« Page 1 of 36 »
Advertisement
Version imprimée

Beaucoup de gens préfèrent de lire les documents dans la version imprimée et non pas sur l'écran. L'option d'impression de l'instruction est aussi prévue et vous pouvez en profiter en cliquant le lien ci-dessus - Imprimez l'instruction. Il n'est pas nécessaire d'imprimer toute l'instruction EMC CX700 - on peut choisir des pages. Economisez le papier.

Résumés

Vous trouverez ci-dessous les annonces des contenus qui se trouvent sur les pages suivantes de l'instruction de EMC CX700. Si vous voulez parcourir rapidement le contenu des pages suivantes de l'instruction, vous pouvez en profiter.

Résumés du contenu
Résumé du contenu de la page N° 1

EMC CLARiiON
CX300, CX500, and CX700
Storage Systems
Initialization Guide
P/N 300-001-272
REV A01
November 26, 2003
This guide explains the initial software setup procedure for the
®
CLARiiON CX300, CX500, and CX700 storage systems. An authorized
EMC service provider will perform these procedures at the customer
site.
Topics include
◆ Initialization Overview.........................................................................2
◆ Requirements for Initial Setup.............................

Résumé du contenu de la page N° 2

Initialization Overview Initialization Overview This section provides an overview of the initialization procedures described in this guide. Tasks highlighted with grey in the checklist should be completed before the service provider arrives at the customer site. Task Procedure 1 Prerequisites ❑ Verify requirements for initial setup (page 3). If your service laptop is not set up for dial-up PPP support or dial-up networking, you must complete the following (page 5): ❑ Set up the dial-up PPP

Résumé du contenu de la page N° 3

Requirements for Initial Setup Requirements for Initial Setup To set up and initialize the storage systems, you will need the following: General Requirements ❑ A CX700, CX500, or CX300 storage system with two storage ™ processors (SPs) that have the required FLARE software and ® EMC Navisphere Agent installed on them. ™ Note Navisphere is a member of the EMC ControlCenter family of products. ❑ A NULL modem cable, with 9-pin, female-male to female-male connectors (supplied with each storage

Résumé du contenu de la page N° 4

Requirements for Initial Setup Service Laptop Requirements Initializing the storage processor enclosure and the accompanying DAE2 disk enclosures requires a directly connected computer — usually a laptop model — that we refer to as a service laptop. ❑ A Windows operating system, as indicated in the EMC Navisphere Manager 6.X Release Notes. ❑ A supported web browser, as indicated in the EMC Navisphere Manager 6.X Release Notes. ❑ Java 2 Runtime Environment, as indicated in the EMC Navisphere

Résumé du contenu de la page N° 5

Setting Up the Service Laptop Setting Up the Service Laptop The PPP-capable (Point-to-Point Protocol) service laptop can be any computer that satisfies the requirements described on the previous page. The service laptop COM port modem type must be set to Dial-Up Networking Serial Cable between 2 PCs. This is the most flexible modem type, and allows either a NULL modem cable or actual modem to connect to the laptop and SP. If the laptop uses a physical modem, configure the modem for the Phy

Résumé du contenu de la page N° 6

Setting Up the Service Laptop Setting Up the Dial-Up PPP Support (Windows 2000 Environment) If Communication cable between two computers is not installed and set up, install it and set it up as follows: 1. Follow the path: Start > Settings > Control Panel > Phone and Modem Options 2. If your laptop has a modem, then under the Modems tab, note which port your current modem is using. 3. Click Add. 4. Select Don't Detect my Modem; I will select it from a list. 5. Click Next. An Add/Remove Hardwa

Résumé du contenu de la page N° 7

Setting Up the Service Laptop Setting Up Dial-Up Networking (Windows 2000 Environment) 1. Follow the path: Start > Settings > Control Panel > Network and Dial Up Connections > Make New Connection The Network Connection Wizard opens. 2. Click Next to begin. 3. Click Connect directly to another computer, then click Next. 4. Click the Guest button, then click Next. The Select a Device list is displayed. 5. From the Select a Device list, select Communications between two computers (COM 1) or selec

Résumé du contenu de la page N° 8

Setting Up the Service Laptop 15. Click the Networking tab. PPP: Windows 95/98/NT 4/2000, Internet should appear in the Type of dial-up server I am calling list. 16. Click Settings. 17. Make sure that Enable LCP extensions and Enable software compression are checked, then click OK. 18. Highlight Internet Protocol (TCP/IP). 19. Click Properties. 20. Select Obtain an IP address automatically and Obtain DNS server address automatically. 21. Click Advanced. Make sure that Use IP header compressio

Résumé du contenu de la page N° 9

Setting Up the Service Laptop Setting Up the Dial-Up PPP Support (Windows NT 4.0 Environment) 1. If Dial-Up Networking between 2 PCs is not installed and set up, install it and set it up as follows: a. Follow the path: Start > Settings > Control Panel > Modems b. If your laptop has a modem, then under the General tab of Modem Properties, note which port your current modem is using. c. Exit, then click Add. d. Select the Don't Detect my Modem; I will select it from a list check box. e. Click

Résumé du contenu de la page N° 10

Setting Up the Service Laptop 2. Configure the serial connection for remote access (RAS) by doing the following: a. In the Add RAS Device dialog box, select the dialup networking serial cable with the correct COM port noted in step 1i. b. Click OK. 3. From the Remote Access Setup dialog box, select the dialup networking serial cable with the correct COM port. 4. Click Configure. 5. In the Port Usage dialog box, select dial out only. 6. Click OK. 7. Click Continue to restart the computer.

Résumé du contenu de la page N° 11

Setting Up the Service Laptop 7. Clear the check box Use another port if busy. 8. Click the Server tab. 9. Set the Dial-up server type to be PPP: Windows NT, Windows 95 Plus, Internet. 10. In the Network Protocols dialog box, select TCP/IP. 11. Click TCP/IP Settings... and do the following in the PPP TCP/IP Settings dialog box: a. Select the Server assigned IP address option. The SP will provide the address for the service laptop. b. Select the Server assigned name server addresses check

Résumé du contenu de la page N° 12

Initializing the Storage System Initializing the Storage System This section describes how to set critical startup parameters on the storage system’s storage processors (SPs). Before you begin the initialization process, have the network administrator at your facility assign IP addresses for the storage system, and complete the following worksheet. You will need this information to complete the system setup. Table 2 Initialization Worksheet SP A SP B Hostname __________________________ ____

Résumé du contenu de la page N° 13

Initializing the Storage System Initialization Steps Follow the steps below to initialize the storage system from the service laptop. These instructions assume that you are starting with SP A. However you can start the initialization process with either SP. 1. Connect the NULL modem cable between the laptop serial port (COM 1) and the SP A service port (|0|0|on a CX700, or on a CX500 SP or CX300 SP), as shown in Figure 1. For a CX500, you will need the RJ45/DB9 serial adapter that shipped

Résumé du contenu de la page N° 14

Initializing the Storage System 3. Depending on your operating system, do one of the following: For Windows 2000 a. On the laptop, select Start > Settings > Network and Dial up Connections. Select the connection name that you assigned when you set up dial-up networking. b. In the Connect dialog box, log in as user clariion with password clariion!. c. Click Connect and click OK on the Connection Complete dialog box. For Windows NT 4.0 a. On the laptop, select My Computer > Dial-up Networking

Résumé du contenu de la page N° 15

Initializing the Storage System Figure 2 Storage Processor Networking Configuration Setup Screen (SP A) EMC CLARiiON CX300, CX500, and CX700 Initialization Guide 15

Résumé du contenu de la page N° 16

Initializing the Storage System 5. Specify the following for SP A: a. IP address b. Hostname c. Subnet Mask d. Gateway address for SP A e. Peer IP address for SP B f. If desired, for example, for added security (see the caution below), change the management port setting to 2162/2163. CAUTION ! Be sure that this is the management port whose setting you want to change. If you later want to change it back, you must remove the node from its domain before you can change its port setting from the

Résumé du contenu de la page N° 17

Initializing the Storage System Figure 3 Network Configuration Confirmation Screen (SP A) 8. Remove the NULL modem cable from SP A and connect it between the laptop serial port (COM 1) and the SP B service port (|0|0|, or ). 9. Depending on your operating system, do one of the following: For Windows 2000 a. On the laptop, select Start > Settings > Network and Dial up Connections. Select the connection name that you assigned when you set up dial-up networking. b. In the Connect to dialog box,

Résumé du contenu de la page N° 18

Initializing the Storage System For Windows NT 4.0 a. On the laptop, select My Computer > Dial-up Networking. Select the connection name that you assigned when you set up dial-up networking. b. Select the phonebook entry you created when you set up the laptop in the previous section. c. Click Dial. d. In the Connect to dialog box, log in as user clariion with password clariion!. Ignore the Domain field. e. Click OK. 10. Open a supported browser, and enter the following URL: 192.168.1.1/setup

Résumé du contenu de la page N° 19

Initializing the Storage System Figure 4 Storage Processor Networking Configuration Setup Screen (SP B) EMC CLARiiON CX300, CX500, and CX700 Initialization Guide 19

Résumé du contenu de la page N° 20

Initializing the Storage System 12. Specify the following for SP B: a. IP address b. Hostname c. Subnet mask d. Gateway address for SP B e. Peer IP address for SP A f. If desired, for example, for added security (see the caution below), change the management port setting to 2162/2163. CAUTION ! Be sure that this is the management port whose setting you want to change. If you later want to change it back, you must remove the node from its domain before you can change its port setting from th


Instructions pareilles
# Instruction d'utilisation Catégorie Téléchargez
1 EMC CX500 Manuel d'utilisation Supports portables de données 6
2 EMC 69001166 Manuel d'utilisation Supports portables de données 0
3 EMC CX300 Manuel d'utilisation Supports portables de données 18
4 Sony SDZ-100 Manuel d'utilisation Supports portables de données 1
5 Sony Ait-1 Tape Cartridge SDX135CAWW Manuel d'utilisation Supports portables de données 1
6 Sony Manuel d'utilisation Supports portables de données 1
7 Sony Micro Vault Mach USM8GQ 8 GB USB 3.0 Flash Drive USM8GQ/S Manuel d'utilisation Supports portables de données 1
8 Sony SDX-400 Manuel d'utilisation Supports portables de données 2
9 Sony Dvcam Cassette PDV64N PDV64N Manuel d'utilisation Supports portables de données 1
10 Sony SDX-410 Manuel d'utilisation Supports portables de données 1
11 Sony Ait-1 Tape Cartridge SDX1-35C Manuel d'utilisation Supports portables de données 1
12 Addonics Technologies ST4ESA Manuel d'utilisation Supports portables de données 1
13 Addonics Technologies ST4US-B Manuel d'utilisation Supports portables de données 1
14 Addonics Technologies ST6ESA Manuel d'utilisation Supports portables de données 1
15 Addonics Technologies ST5X1PM-B Manuel d'utilisation Supports portables de données 0