Résumé du contenu de la page N° 1
Owner’s Manual
Model
WRCPF-KIT
IMPORTANT SAFETY INFORMATION: Always read this manual first
before attempting to install or use this device. For your safety, always
comply with all warnings and safety instructions contained in this manual
to prevent personal injury or property damage.
To view the full line of Dimplex products, please visit
www.dimplex.com
7209110100R03
Résumé du contenu de la page N° 2
Table of Contents Welcome & Congratulations . . . . . . . . . . . . 3 Product Overview ..................... 4 Receiver Installation (BF units only) ...... 5 Wall Control Installation ............... 7 Initialization ........................ 14 Operation .......................... 15 Warranty .......................... 20 ! NOTE: Procedures and techniques that are considered important enough to emphasize. CAUTION: Procedures and techniques which, if not carefully
Résumé du contenu de la page N° 3
Welcome & Congratulations Thank you and congratulations for choosing to purchase a Wall Switch Remote Control Kit from Dimplex, the world leader in electric fireplaces. Please carefully read and save these instructions. CAUTION: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard and will void the warranty. NO NEED TO RETURN TO THE STORE Questions with operation or assembl
Résumé du contenu de la page N° 4
Product Overview The Wall Switch Remote Control ! NOTE: This equipment has been tested and found to comply with Kit is designed to work with the limits for Class B digital device, the following Dimplex electric pursuant to part 15 of the FCC Rules. fireplaces: These limits are designed to provide reasonable protection against harmful • BF33STP interference in a residential installation. This equipment generates, uses and • BF33DXP can radiate radio frequency energy • BF39STP a
Résumé du contenu de la page N° 5
Receiver Installation (BF units only) 1. Open steel curtain (remove Figure 2 Log glass doors if applicable). ember Back bed 2. Remove two (2) screws on log ledge grate and remove log grate (Figure 1). Rear Figure 1 tab Front Side section edge 4. Locate and remove the two (2) screws on the manual control bracket (Figure 3). Remove the bracket. 5. Locate and depress the mounting tabs on the plug connector and remove the manual control bracket from Screws fireplace (Figure 3). Man
Résumé du contenu de la page N° 6
Receiver Installation (BF units only) 6. Locate the plastic 9-pin plug ledge (Figure 2) and the logs in the bottom corner of the are resting against the partially fireplace where the manual reflective glass. controls were plugged in to. 11. Replace log grate using two 7. Insert the plug connector from (2) screws previously removed the remote control bracket in step 2. (Figure 4) into plastic plug inside the fireplace. Figure 4 Antenna Plug Connector Remote Control 8. Run black antenna
Résumé du contenu de la page N° 7
Wall Control Installation ! NOTE: All electrical wiring available 24V~ power source must comply with all national should be considered. and local electrical codes WARNINg: Electrocution or and regulations. Always other bodily harm and property use a qualified and licensed damage can occur if a live electrician should you have wire is touched or damaged any questions or concerns for during installation. Always all wiring work. consult electrical schematics for the installation
Résumé du contenu de la page N° 8
Wall Control Installation 2. Release the Controller from 3. Open the Battery Compartment its Outer Housing by pushing as shown in Figure 6 and the front face into the Outer remove the Insulating Strip as Housing until you hear a click. shown in Figure 7. This will release the push- lock latches and allow the Figure 7 Controller to be removed from the Outer Housing (Figure 5). Outer Figure 5 Housing Insulating Strip 4. Replace the battery compartment cover. 5. Reinsert the Controller
Résumé du contenu de la page N° 9
Wall Control Installation to complete the installation Figure 8 and to blend the installation in Tracks with your choice of decor. Controller Hard Wired Power Supplied Installation Before starting this installation, it is helpful to initialize the Wall Switch Remote Control with your firebox (see Initialization section). You should have the following Outer items ready and prepared: Guides Housing • Installed standard wall device box with a minimum depth of Figure 9 2.5 inch (6.35
Résumé du contenu de la page N° 10
Wall Control Installation 1. Unpack the Wall Switch of the two holes located on the Remote Control and all wire lead storage compartment hardware from its package. cover (make sure orientation is as shown as in Figure 11). 2. Release the Controller from its Outer Housing by pushing Figure 11 the front face into the Outer Housing until you hear a click. This will release the push- lock latches and allow the Controller to be removed from the Outer Housing (Figure 5). 3. Push the wire
Résumé du contenu de la page N° 11
Wall Control Installation Outer Figure 12 Locking Screw Option (Figure 14) Housing To prevent tampering, damage, and theft, it is suggested to install the locking screws. Once installed, the locking screws will prevent the Controller from being released from the Outer Housing without being removed first from the device box in the wall. Controller ! NOTE: A Philips head screwdriver will be required for this step. Figure 13 Figure 14 Locking screws Outer Housing 8. Using the wiring
Résumé du contenu de la page N° 12
Wall Control Installation Ensure each of the two Figure 15 Controller lead wires are connected to separate Low Voltage 24V~ only wires. Low Voltage Controller 24V~ power source ONLY wire leads Figure 16 Flat Head Screws (supplied) 12 www.dimplex.com
Résumé du contenu de la page N° 13
Wall Control Installation ! NOTE: Wire leads are not polarized due to the nature of this device. 9. Coil excess wiring to the back of the device box and insert the Controller and Outer Housing into the device box (Figure 16). Fasten with two supplied flat head screws. 10. Attach your choice of Decora style faceplate (not supplied) to complete the installation and to blend the installation in with your choice of decor. 11. Initialize the sender with the receiver installed in your
Résumé du contenu de la page N° 14
Initialization After installation, locate the 4. Press any button on the Wall section which applies to your Switch Remote Control within specific model of fireplace and that 10 seconds. follow the steps for remote control BLF50 Models initialization and if required, 1. Ensure that power is supplied re-initialization. Refer to your through main service panel. fireplace's owner's manual to locate manual or other controls as 2. Inside the fireplace, turn Main needed. On/Off Switch to O
Résumé du contenu de la page N° 15
Initialization DF3033ST and DFg3033 Models 3. Set the 3 Position Manual Control (Figure 19B) to the 1. Ensure that power is supplied Remote position (left position). through main service panel. 4. Press and hold the 2. Ensure the Main On/Off Switch Initialization Button on the unit located in the switch box on (Figure 19C). the fireplace in the upper right hand corner is in the On 5. While holding the Initialization position (Figure 19A). Button, press any button on the Wall Swit
Résumé du contenu de la page N° 16
Operation Figure 20 • OFF (center): Makes the unit inoperable. A B C • MANUAL (top): All functions of the fireplace are controlled by the On and Off buttons as described above (A, B). • REMOTE (bottom): All functions of the fireplace are controlled by the Wall Switch Remote Control. D D. LED Indicators A. On Button Depicts which of the three (3) Pressing this button toggles levels the fireplace is currently sequentially through the three operating at: Level 1 - flame effect levels
Résumé du contenu de la page N° 17
Operation Wall Switch Remote Control 6 7 5 1 2 8 9 10 11 12 13 4 3 14 Display Operation 1. Room Temperature 8. Set Temperature Down 2. Set Temperature 9. Set Temperature Up 3. Flame Effect 10. Flame Off 4. Purifire™ 11. Flame On 5. Heat Off Indicator 12. Purifire™ Off 6. Function Lock Indicator 13. Purifire™ On 7. RF Code Function Indicator 14. Low Battery Indicator 17
Résumé du contenu de la page N° 18
Operation 1. Room Temperature those units with the Purifire™ installed. Displays current ambient temperature in the room. 5. Heat Off Indicator 2. Set Temperature This function manually overrides the thermostat control and Displays and controls the heater prevents the fireplace’s heater to the temperature at which the from coming on. thermostat is currently set to. Press 8 to lower the thermostat To do this, press 8 to decrease and press 9 to raise the Set Temperature to any o o
Résumé du contenu de la page N° 19
Operation 7. RF Code Function and Other Functions Change Procedure 6 Hour Sleep Timer In the event that the Wall Switch This feature ensures all functions Remote Control does not work are turned off six hours after any properly with the receiver due last button has been pressed. to interference from additional To turn this feature on and wireless signals, this function will off press 9, 11, 10, and 8 allow the RF code to be changed. sequentially. To enable this function, press When
Résumé du contenu de la page N° 20
Warranty This Dimplex Wall Switch Remote customer shall be responsible for all costs Control is warranted against defects in incurred in the removal or reinstallation workmanship and materials for two years and shipping of the product for repairs. from date of sale. This warranty does not Within the limitations of this warranty, apply to damage from accident, misuse, inoperative units shall be returned to or alteration, nor where the connected the nearest Dimplex authorized service voltag
