Résumé du contenu de la page N° 1
TOSHIBA POS Terminal
ST-A20 SERIES
Owner's Manual
Résumé du contenu de la page N° 2
CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Warnung Dies ist ein Klasse A Produkt. In einer örtlichen Umgebung kann dieses Gerät Funkstörungen verursachen. ATTENTION Ce produit est de classe A. Dans un environnement domestique, il
Résumé du contenu de la page N° 3
Safety Summary EO1-12037 Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment. Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified using the procedures described in this manual,
Résumé du contenu de la page N° 4
Safety Summary EO1-12037 If foreign objects (metal When unplugging the power cords, Disconnect Disconnect fragments, water, liquids) enter be sure to hold and pull on the plug the plug. the plug. the machines, first turn off the portion. Pulling on the cord portion power switches and disconnect may cut or expose the internal wires the power cord plugs from the and cause fire or electric shock. outlet, and then contact your authorized TOSHIBA TEC representative for assistance.
Résumé du contenu de la page N° 5
EO1-12037 TABLE OF CONTENTS Page 1. INTRODUCTION ------------------------------------------------------------------------- 1-1 1.1 Accessories -------------------------------------------------------------------------------- 1-1 2. APPEARANCE --------------------------------------------------------------------------- 2-1 2.1 Standard Model ---------------------------------------------------------------------------- 2-1 2.2 Availabe Options ----------------------------
Résumé du contenu de la page N° 6
EO1-12037 1. INTRODUCTION 1.1 Applicable Model 1. INTRODUCTION Thank you for choosing the TOSHIBA POS Terminal. This POS terminal contains all the high performance register functions necessary for a specialty/hospitality POS terminal and enables the user oriented system configuration. The operation panel can be chosen from 12-inch TFT display and 15-inch TFT display. This m
Résumé du contenu de la page N° 7
EO1-12037 2. APPEARANCE 2. 1 Standard Model 2. APPEARANCE 2.1 Standard Model 12-inch display POS terminal 15-inch display POS terminal 2-1
Résumé du contenu de la page N° 8
EO1-12037 2. APPEARANCE 2. 1 Standard Model 2-2
Résumé du contenu de la page N° 9
EO1-12037 2. APPEARANCE 2.2 Available Options LED and CONTROL BUTTON DESCRIPTION This is the LED to indicate the power ON/OFF status of the POS terminal. The blue LED is Power LED (Blue) illuminated when the power is ON. The yellow LED is illuminated during the HDD LED (Yellow) access to the hard disk drive. This is th
Résumé du contenu de la page N° 10
EO1-12037 2. APPEARANCE 2.2 Available Options 2.2 Available Options Wireless Adaptor Case Fixed type customer display BIU Magnetic Card Reader Tilt type customer display (MCR) BIU iButton Remote type customer display RIU 2-4
Résumé du contenu de la page N° 11
EO1-12037 2. APPEARANCE 2.3 Examples of POS Terminal with Some Options 2.3 Examples of POS Terminal with Some Options 2-5
Résumé du contenu de la page N° 12
EO1-12037 2. APPEARANCE 2.4 Connectors 2.4 Connectors CAUTION! The drawer interface connector is exclusively for connecting the drawer. Do not connect a phone line or any other cables than the drawer cable to this connector. Doing so may cause a failure of the phone line and this terminal.
Résumé du contenu de la page N° 13
EO1-12037 2. APPEARANCE 2.4 Connectors Connector Description AC inlet A connector for the AC inlet PS/2 (Mouse, Keyboard) Mini-DIN 6- Connector for the PS/2 type mouse, Connector for the pin female type connector PS/2 type keyboard Connector for the USB (Universal Serial Bus) interface USB V2.0/1.1 and UHCI (Conforming
Résumé du contenu de la page N° 14
EO1-12037 3. INSTALLATION PROCEDURE 3.1 Environment for Installation 3. INSTALLATION PROCEDURE WARNING! Care must be taken not to get your fingers caught between the LCD Frame and the POS terminal when bending the display downward. CAUTION! When removing the protective film from the display surface, please be sure to do it slowly. If it is done quickly, sta
Résumé du contenu de la page N° 15
EO1-12037 3. INSTALLATION PROCEDURE 3.2 Connecting the AC Plug 3.2 Connecting the AC Plug 1. Push on both sides of the molded Tower (TWR) Tail Cover to remove it from the system in order to gain access of the AC inlet. 2. Fully insert the Power Cord Plug into the Inlet of the POS terminal. Power Cord Plug TWR Tail Cover Inlet
Résumé du contenu de la page N° 16
EO1-12037 4. ADJUSTMENT 4.1 Tilt Angle Adjustment 4. ADJUSTMENT Tilt angle and brightness of the operator’s display can be adjusted. Adjustment method is common to both of 12-inch display model and 15-inch display model. CAUTION! 1. Do not adjust the display angle by holding the LCD panel. Doing so may damage the unit. Be sure to hold the LCD frame. 2. Care must be taken not to catch your fingers between POS terminal and the LCD Frame when bending the display backward.
Résumé du contenu de la page N° 17
EO1-12037 4. ADJUSTMENT 4.2 Brightness Adjustment 4.2 Brightness Adjustment The brightness control is provided on the lower right of the operator’s display. Turning it to the left makes the display darker, and turning it to the right makes the display brighter. 4-2
Résumé du contenu de la page N° 18
EO1-12037 4. ADJUSTMENT 4.3 Volume Adjustment 4.3 Volume Adjustment The volume control is provided on the lower right of the tower. Turning it to the left makes the volume lower, and turning it to the right makes the volume higher. 4-3
Résumé du contenu de la page N° 19
EO1-12037 5. MAGNETIC CARD READER (OPTION) 5.1 How to Read Magnetic Card 5. MAGNETIC CARD READER (OPTION) The optional magnetic card reader can be installed. 5.1 How to Read Magnetic Card Insert the magnetic card into the upper portion of the magnetic card reader slot and slowly move the card downward. NOTE: Moving the magnetic card too fast or too slowly may cause a read error. 5-1
Résumé du contenu de la page N° 20
EO1-12037 6. iBUTTON® (OPTION) 6.1 How to Read iButton ® 6. iButton (OPTION) The optional iButton unit can be installed on the bottom of the LCD. 6.1 How to Read iButton CAUTION! 1. Keep storage media, like a floppy disk, away from the touch probe. The magnet of the touch probe may destroy the stored data 2. Keep a metal object like a paper clip away
