Résumé du contenu de la page N° 1
3 HP
Air Compressor Pump
93785
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2006 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For techni
Résumé du contenu de la page N° 2
Specifications CastAluminum Pump, Single Stage, Construction: Compressor Type: Flywheeland Head. TwinCylinder Mi aximum Pressure:1: 40 ps Mm aximum Speed 1200 rp SplashOiltype withOilLevel 8.7 cfm at40 psi Lubrication: Windowand BallBearing Air DeliveryRate at1050 rpm: 7.7 cfm at90 psi Check Release Valve 6.95 cfm at115 psi 10-¼" Dia.x1-3/8"W PulleyDimensions: Pe istonDimensions: 65mm Dia.x50mm strok withV-groove for belt OH verallDimensions:1: 2-¼"L x10-¼"W x12-¼"N. etWeight 23 lbs Caution: Bef
Résumé du contenu de la page N° 3
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically non-conductive clothes and non-skid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 7. Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts
Résumé du contenu de la page N° 4
18. Maintenance. For your safety, service and maintenance should be performed regularly by a qualified technician. Note: Performance of this Air Compressor Pump may vary depending on variations in local line voltage or motor capacity. Extension cord usage may also affect tool performance. 19. Use proper size and type extension cord. If an extension cord is required, it must be of the proper size and type to supply the correct current to the tool without heating up. Otherwise, the extension cord
Résumé du contenu de la page N° 5
Air Compressor Pump Safety Precautions 1. Use proper size motor and motor pulley. This air compressor Pump must be installed with a 3 HP electric motor and pulley (both not supplied) which can turn the Air Compressor Belt Wheel (35) at approximately 1050 rpm, but not more than 1200 rpm. 2. Install motor, pully belt and pully belt cover securely. Be sure to use the proper size bolts to install your motor (not included). The belt and belt cover (not included) must be strong enough to prevent brea
Résumé du contenu de la page N° 6
Unpacking When unpacking, check to make sure that the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Installation Note: Depending on your level of expertise, you may wish to have a qualified technician perform this installation. Caution: Avoid damage to the Air Compressor Pump and other equipment. Make sure the mounting surface for the Air Compressor Pump is installed on a flat
Résumé du contenu de la page N° 7
Note: A qualified electrician must wire in a pressure switch control that turns off the motor when the pump reaches the desired pressure (less than 140 PSI). Note: Always install this Air Compressor Pump to an air tank that has a pressure release valve set at less than 140 PSI. Note: A high/low cut-in/cut-out switch (not included) can be incorporated to operate a motor starter or motor contractor for semi-automatic control of air pressure in the vessel. Warning: Avoid serious injuries. Do not op
Résumé du contenu de la page N° 8
Parts List Pn art #D. escriptio Q# TYPn artD. escriptio QTY 1rW6 ashe 132tO1 ilWindowGaske 2tB4 ol 142tO1 ilDrainBol 3wS6 cre 2l5S1 ea 4rA2 ir Filte 2t6G1 aske 5dC1 ylinder Hea 2r7B1 ase Cove 6tA1 ir Outle 2g8B2 earin 7t *G1 asketValve Sea 2t9C1 rankshaf 8t *V1 alve Sea 3l0O1 ilSea 9t *G4 asketValve Sea 3r1E1 nd Cove 1e 0*V1 alve Plat 3w2S1 cre 1t 1*C4 ylinder Head Gaske 3r3S1 pring Washe 1r 2C1 ylinde 3r4W1 ashe 1w 3S1 cre 3l5B1 eltWhee 1t 4C6 ylinder Gaske 3t6N1 u 1k 5D1 ipstic 3w7S4 cre 1e 6C
Résumé du contenu de la page N° 9
Assembly Drawing 44 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENT
