Résumé du contenu de la page N° 1
STORAGE DEVICE DIVISION
SR-C8002
CD-R/CD-RW DRIVE
PRODUCT SPECIFICATION
MAY 2001
REV. 1.0
Specifications are subject to change without notice
DOCUMENT NUMBER
14708
Résumé du contenu de la page N° 2
LIMITATION OF LIABILITY Those warranties in the express warranty separately agreed between TOSHIBA and your company are the only warranties given to the consumer and are in lieu of any other warranties, whether express or implied with regard to this component. TOSHIBA expressly and unequivocally disclaims the warranties of merchantability and fitness for a particular purpose. Further, TOSHIBA disclaims all express warranties created by any individual or entity installing this device into a compu
Résumé du contenu de la page N° 3
DO NOT use this equipment in the system such as medical equipment which may cause personal injury or property damages resulting from malfunction of this equipment and unexpected data corruption or data error in reading operation. 4. Turn off the power for this equipment and wait more than one (1) minute before you eject the disc using the emergency eject mechanism when a disc cannot be ejected for some reasons in order to avoid the risk of damages to the disc. Notice 1. Turn off the system power
Résumé du contenu de la page N° 4
Contents 1. Introduction ---------------------------------------------------------------------------------------------------------------------- 1 2. Features -------------------------------------------------------------------------------------------------------------------------- 1 3. Specifications ------------------------------------------------------------------------------------------------------------------ 2 3.1. Performance -----------------------------------------------------------------
Résumé du contenu de la page N° 5
7.2. Current Drain -------------------------------------------------------------------------------------------------------18 7.2.1.Sleep ------------------------------------------------------------------------------------------------------------18 7.2.2. Standby ----------------------------------------------------------------------------------------------------------18 7.2.3. Continuous Read -------------------------------------------------------------------------------------------18 7.2.4. Idle
Résumé du contenu de la page N° 6
1. Introduction This document describes TOSHIBA's SR-C8002 CD-R/RW Drive. 2. Features SR-C8002 reads digital data stored on CD-ROM media and CD-Audio discs. The CD-ROM media has a 12 cm or 8 cm diameter. It typically contains approximately 20 600 MBytes or 200 MBytes of information respectively. (1 MByte=2 Bytes) This drive reads CD-ROM media at maximum 24 times faster rotational speed. This drive is a new generation drive with highest performance such as 120 ms access Time. This drive write
Résumé du contenu de la page N° 7
3. Specifications 3.1.Performance (1) Applicable Write Format CD-R/RW: Disc at once, Track at once, Session at once, Packet write 1 (2) Applicable Write Disc * CD-R/RW: CD-DA, CD+(E)G, CD-MIDI, CD-ROM,CD-ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video-CD) Multisession CD (Photo-CD, CD-EXTRA, Portfolio) 2 (3) Applicable Read Disc * CD : CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, , CD-ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video-CD) Multisession CD (Photo-CD, CD-EXTRA, Port
Résumé du contenu de la page N° 8
(6) Transfer Rate Sustained Block Transfer Rate 776-1,800 Block/s (10.3-24X CAV) 300-450 Block/s (4-6X PCAV) Sustained Data Transfer Rate Mode-1: 10.3X-24X CAV 1,552-3,600 KByte/s 4X-6X PCAV 600-900 KByte/s Mode-2: 10.3X-24X CAV 1,769-4,104 KByte/s 4X-6X PACV 684.4-1,026.6 KByte/s Burst Data transfer Rate 16.7 MByte/s (PIO Mode 4 ) 16.7 MByte/s ( Multi word DMA transfer mode-2) 10 20 ( 1 KByte=2 Byte=1,024 Bytes, 1 MByte=2 Byte=1,048,576 Bytes) (7) Access Time 4 Average Random Access Time* 120
Résumé du contenu de la page N° 9
(10) Drawer Load/Release Load: Manual Release: (a) Electrical Release (Release Button) (b) Release by ATAPI command (c) Emergency Release (11) Air Flow Not Required (12) Acoustic Noise 40 dB (IEC 179 A weighted at 1 m) (13) Power Supply +5 V (details in Section 7) 3.2. Environmental Conditions This drive should be used under the conditions listed below. 3.2.1.Temperature and Humidity (1) Operating Temperature 5 °C to 50 °C *1 (2) Storage Temperature -10 °C to 60 °C (3) Shipping Temperature -40 °
Résumé du contenu de la page N° 10
3.2.3.Vibration (1) Operating (CD 10.3-24X Read) (1 Oct/min) ---------------- no hard error ----- 2 5 to 500 Hz 2.45 m/s [0.25 G] (0-p) (excluding resonance point) (2) Operating (Write) (1 Oct/min) ---------------- no hard error ----- 2 5 to 500 Hz 2.45 m/s [0.25 G] (0-p) (excluding resonance point) (3) Non-operating (1 Oct/min) --------- no damage ----- 5 to 10 Hz 5 mm (p-p) 2 10 to 500 Hz 9.8 m/s [1 G] (0-p) (4) Shipping (Packaged) (1 Oct/min) ----- no damage ----- 2 10 to 25 Hz 9.8 m/s [1G] (
Résumé du contenu de la page N° 11
3.3. Installation Conditions 30° 15 ° 15° 15 ° 15 ° 15° 15 ° 15° 15° 15° Figure 1 Mounting angle 3.3.1. Equipment (1) When mounting the equipment, use four M2-P0.4 tapping holes located on the left and right sides of the equipment. (2) The opposite surface of the bearing surface (fitting surface when mounting) of the tapping holes must be kept flat so that the bearing surface can be fit evenly. (3) Use the mounting screws which do not enter deeply inside the equipment more than specified value.
Résumé du contenu de la page N° 12
(4) Do not add the force beyond the indicated force on the top and bottom cover of the equipment. (The restricted force range for the top cover is shown in the Figure 2.) (For the bottom cover, the applied force should be less than 2N on whole area.) 2 N 1 N R63 0.5 N R59 37 24 R46 Do not add the force 5.4 20 Figure 2 Restricted force range applied for the top cover (5) The characteristics of EMC (Electro Magnetic Compatibility) are primarily influenced by the mounting method of this equipment.
Résumé du contenu de la page N° 13
( Unit: mm ) Figure 3 External Dimensions 8/24 SR-C8002 Rev.1.0
Résumé du contenu de la page N° 14
3.5. Reliabilites 3.5.1. Error Rate (1) Hard Read Error Rate (Byte Error Rate) ----- Allowing 5 Retries(default) ----- -15 Mode 1:10 Max -12 Mode 2:10 Max -6 (2) Seek Error Rate --- Allowing 10 Retries 10 Max (default) 3.5.2. MTBF 60,000 h Assumptions: Power On Hours 5,436 h/year On/Off Cycles 313 cycles/year Number of Access 600,000 accesses/year Operating Duty Cycle (Read) 20 % of Power On Time (Reading/Seeking) Operating Duty Cycle (Write) 2 % of Power On Time (Writing/Seeking) 3.5.3. MTTR
Résumé du contenu de la page N° 15
BUS Control Clock Figure 4 Configuration 10/24 SR-C8002 Rev.1.0 CD-R / RW DRIVE MODEL SR-C8002 BLOCK DIAGRAM TA1323F DRAM (1M) AK8570A TC94A03 ATIP Filter EQL D-RAM Interface RF Amp Tracking Amp Data Slicer PLL PUH Disc Motor Tracking Amp Focus Amp Demodulator EDC ECC Focus Amp Laser Control Feed Motor De-Scramble Command Dec. Commad DCC Memory Controller Position A/D Converter Detector MM3067 BH6526FV D/A Track EQL Audio Servo D/A Muting Power Driver Controller D/A Focus EQL Power
Résumé du contenu de la page N° 16
5.Functions 5.1. Disc Data Configurations 5.1.1. CD-ROM Data Configurations Figure 5 shows how the data is structured in program units 1 block=1/75 s TNO Time TOC Lead-in SYNC 0 Minutes 12 bytes 1-Disc Min Second(0~59) 4 bytes Header Block 1 Sec Blocks(0~74) Block User Data 2048 bytes in Mode-1 Mode 1 Min 2336 bytes in Mode-2 Block 2 Sec ~ ~ Block ECC (Mode-1) approx. 288 bytes ~ ~ 2 300 k-Blocks ~ ~ ~ ~ Lead out AA Figure 5 CD-ROM Disc Data Configuration 5.1.2. CD-R / CD-RW Data Configurations
Résumé du contenu de la page N° 17
5.2. Power ON/OFF Timing Figure 7 shows the initialization sequence Power ON or ATAPI-RST Max. 550 ms "Command" Receivable System Initialization Max 2 s Focus Search Max 3.5 s Spindle ON Learning Max 30s, Typ 12 s (Single Session Disc) "Read-Command" Stand-by Acceptable "TEST UNIT READY" "Check Condition" Status "Good" Status Command Figure 7 Initialization Sequence 6. Interfa
Résumé du contenu de la page N° 18
6.2.Signal summary The physical interface consists of single ended TTL compatible receivers and drivers communicating through a 50P-connector as shown in Figure 11 and Figure 12 "Interface connector". 6.2.1. Signal Specification Figure 8 shows the Signal Specifications Receivers/Drivers Caracteristics withoutExternal pullup Resistor NOTE Type Sig. Name Condition Min Max Bidirectional IOH=1 mA Voltage Output High Vdd-0.4 V Rx=infinity VOH Rx Rs1=0 OHM IOL=12 mA Voltage Output Low 0.4 V VOL Rs2=33
Résumé du contenu de la page N° 19
6.2.2.Timing of Host Interface (PIO) Figure 9 shows the Host Interface Timings t0 Address valid*1 t2 t1 t9 DIOR-/DIOW-*1 t2i Write data valid*1 t3 Read data valid*1 t4 t5 t6Z t7 t6 IOCS16-*1 tA tB t8 IORDY tRD *1: In all timing diagrams, the low line indicator negated, and the upper line indicators asserted. PIO timing parameters min (ns) max (ns) Min Time (ns) Max Time (ns) t0 Cycle time 120 t1 Address valid to DIOR/DIOW-setup 25 t2 DIOR/DIOW-pulse wide 70 t2i DIOR/DIOW-recovery t
Résumé du contenu de la page N° 20
6.2.3.Timing of Host Interface (DMA Multi) Figure 10 shows the Host Interface DMA multi word Timings t0 DMARQ tL DMACK-*1 tK tD tI tJ DIOR-/DIOW-*1 tZ tE Read DD0-15 tF Write DD0-15 tH tG *1: In all timing diagrams, the low line indicator negated, and the upper line indicators asserted. Multi word DMA Min time (ns) Max time (ns) timing parameters min(ns) max(ns) Cycle time t0 120 DMACK to DMREQ delay tC --- DIOR-/DIOW-16-bit tD 70 DIOR- data access tE --- DIOR- data hold tF 5 DMACK- to tristate
