Résumé du contenu de la page N° 1
Portable Utility PUmP
65836
Set UP and oPerating inStrUctionS
®
distributed exclusively by Harbor Freight t ools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
SaVe tHiS manUal.
© ®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without t
Résumé du contenu de la page N° 2
notice is used to SaVe tHiS manUal address practices Keep this manual for the safety warn- not related to personal injury. ings and precautions, assembly, operat- caUtion, without ing, inspection, maintenance and cleaning the safety alert procedures. Write the product’s serial symbol, is used to address number in the back of the manual near the practices not related to assembly diagram (or month and year of personal injury. purchase if product has no number). Keep this manual and
Résumé du contenu de la page N° 3
plugs with grounded power tools. Safety equipment such as dust mask, Unmodified plugs and matching out- non-skid safety shoes, hard hat, or lets will reduce risk of electric shock. hearing protection used for appropri- ate conditions will reduce personal b. avoid body contact with grounded injuries. surfaces such as pipes, radiators, ranges and refrigerators. There is c. Prevent unintentional starting. an increased risk of electric shock if ensure the switch is in the off-po- your body i
Résumé du contenu de la page N° 4
proved for the specific hazards in the g. Use the power tool, accessories work area. and tool bits etc. in accordance with these instructions, taking into 4. Power tool use and care account the working conditions a. do not force the power tool. Use and the work to be performed. Use the correct power tool for your ap- of the power tool for operations differ- plication. The correct power tool will ent from those intended could result do the job better and safer at the rate in a hazardo
Résumé du contenu de la page N° 5
• Properly maintain and inspect to groUnding avoid electrical shock. t o PreVent • Any power cord must be properly electric SHocK grounded. Ground Fault Circuit Inter- and deatH From rupter (GFCI) should also be imple- incorrect groUnding mented – it prevents sustained elec- Wire connection: trical shock. Check with a qualified 6. WARNING: Handling the cord on electrician if you are in doubt this product will expose you to lead, as to whether the outlet is a chemical known to the
Résumé du contenu de la page N° 6
of electric shock. (See 3-Prong Plug 2. Double insulated tools may be used and outlet.) in either of the 120 volt outlets shown in the preceding illustration. (See 2. The grounding prong in the plug is outlets for 2-Prong Plug.) connected through the green wire in- side the cord to the grounding system extension cords in the tool. The green wire in the cord must be the only wire connected to 1. Grounded tools require a three wire the tool’s grounding system and must extension cord.
Résumé du contenu de la page N° 7
dition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect the extension cords from sharp objects, excessive heat, and damp or wet areas. recommended minimUm Wire gaUge For eXtenSion cordS* (120/240 Volt) eXtenSion cord namePlate lengtH amPereS (at full load) 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18 16 14 12 12 7.1 – 12.0 18 14 12 10 - 12.1 – 16.0 14 12 10 - - 16.1 – 20.0 12 10 -
Résumé du contenu de la page N° 8
note: For additional information regarding SPeciFicationS the parts listed in the following pages, Electrical Requirements 115 V~ / 60 Hz / 8.4 A refer to the Assembly Diagram near the end of this manual. Pumping Capacity 1500 GPH Max. 1” x 11.5 TPI Inlet & Outlet Size (Standard Hose Size) assembly Pump Lift Capacity 120 Feet 1. Inlet and outlet hoses (not included) must be attached to pump prior to use. UnPacKing 2. Attach inlet and outlet hoses to Hose When unpacking, check to make sure
Résumé du contenu de la page N° 9
5. Never operate this tool in explosive t ool Set Up atmospheres. t o PreVent SerioUS injUry general operating instructions From accidental oPeration: 1. Attach inlet and outlet hoses (not t urn the Power Switch of the included) to pump. Standard garden tool to its “oFF” position and hoses will work. unplug the tool from its 2. Attach accessory Basket Filter to inlet electrical outlet before end of inlet hose. performing any inspection, maintenance, or cleaning 3. Place basket filt
Résumé du contenu de la page N° 10
a. Remove the brush cap on each side maintenance and of the motor housing. Ser Vicing b. Remove the carbon brushes from Procedures not specifically the housing. Keep track of which explained in this manual orientation the old carbon brush- must be performed only by a es were in to prevent needless qualified technician. wear if they will be reinstalled. c. If either carbon brush is worn down t o PreVent by more than 1/2, replace both car- SerioUS injUry bon brushes. From accidental
Résumé du contenu de la page N° 11
t roubleshooting Problem Possible causes likely Solutions Tool will not start 1. No power at outlet. 1. Check power at outlet. 2. Cord not connected. 2. Check that cord is plugged in. 3. Worn out or damaged Carbon 3. Replace Carbon Brushes. Brushes. Pump operates 1. Pump is not primed. 1. Prime pump, see instructions page 9. but does not 2. Basket Filter is clogged. 2. Check and clean basket filter. pump water 3. All water has been pumped out. 3. Turn off pump and complete mop up by hand. 4. I
Résumé du contenu de la page N° 12
aSSembly diagram SKU 65836 For technical questions, please call 1-800-444-3353. Page 12
