Résumé du contenu de la page N° 1
b-1
ACCUSPLIT®
EXCLUSIVE
AX602M500
AX602M500DEC
ACCUSPLIT, Inc.
DIGITAL QUARTZ
6120 Stoneridge Mall Rd., Suite 210
STOPWATCHES
Pleasanton, CA 94588 USA
800-965-2008 • 925-226-0888 • FAX 925-463-0147
OPERATING
www.ACCUSPLIT.com • support@ACCUSPLIT.com
INSTRUCTIONS
980-314
2-3
IMPORTANT NOTE
INSTRUCTIONS
This stopwatch can store up to 500 split/lap times.
Introduction
However please note when there are 5 free mem-
You are about to enjoy an advanced Cumula-
ories left, the icon “FULL ” will
Résumé du contenu de la page N° 2
4-5 • Three operating modes (Countdown Repeat, General Features Countdown Stop, Countdown then count up) • ACCUSPLIT X case with ergonomic design and for countdown timer no-fail buttons • Stroke/Stride measurement basing on “3” • 4 button operation • Speed measurement (AX602M500 Model only) • Large LCD display with contrast adjustment • Decimal second, minute and hour chronograph • 12/24 hour display (AX602M500DEC Model only) • Time of day and chime • Beep sound selectable • Daily alarm
Résumé du contenu de la page N° 3
8-9 This is only a brief description of these buttons. Time of Day Mode Detailed uses of the buttons are different in The starting point for operating your stopwatch particular functions and will be described later in is TIME OF DAY. If TIME OF DAY is not displayed, the instructions. press [Mode] until it is. Pressing [MODE] button will toggle among the Year : - 2008 modes above. Note that there is no auto-return Date : - January 1 function in the stopwatch. Whenever you change Day of
Résumé du contenu de la page N° 4
12-13 date-month (d-m), Sound ON or OFF, Contrast Press [START • SPLIT] conse- C O n T (darkness of the digits - default is 9), then back to cutively to advance the contrast 1 6 Second, and recycles again. up to 16, then cycle back to 1. The contrast setting will be Note: when the second is to be set, press [START shown on the display. • SPLIT] to reset the second digits to zero. At the end of setting, press [RECALL] (S4) or [MODE] to NOTE: exit from the setting mode and back to Time of
Résumé du contenu de la page N° 5
16-17 The upper line shows the split time, the middle Chronograph and Recall Mode line shows the lap time and the accumulated Press [MODE] until you enter the Chrono mode. elapsed time is displayed on the lower line. Whenever the stopwatch stops running, the “STOP” indicator will be ON. Press the button [START • SPLIT] to start the stopwatch. As it runs, the current elapsed time is shown on the lower line. ° Split time Split The stopwatch can measure up to 19 hours, counter ° Lap
Résumé du contenu de la page N° 6
20-21 When there are 5 free memories left, the icon Decimal Timing “FULL ” will blink to remind you of the nearly (AX602M500DEC model only) full situation. Whenever the storage is full, extra split/lap times will not be stored into memory but 1. The DEC Model can operate as a normal 1/100 will still be shown on the display. Any fastest and second chronograph as well as decimal minute, decimal second, and decimal hour chronograph. slowest laps will not be stored. The memory coun- ter will
Résumé du contenu de la page N° 7
24-25 Please note that if the stopwatch is running, no Chronograph Data Recall Mode selection for chronograph operating modes can Press [RECALL] in Chronograph mode to recall be made until the stopwatch has been stopped stored split/lap time memories. The mode message and reset. will be shown up for one to two seconds as mode Segmented run memory for lap/split time storage. message display is enabled. A header consisting of the date/time stamp is attached to each segment to indicate the m
Résumé du contenu de la page N° 8
28-29 [RECALL] [RECALL] Note: watch is [RECALL] still running [RECALL] so run time continues to advance. After recalling the fi rst record, press [RECALL] once more to exit from Recall mode and go back [RECALL] to chronograph mode. The “RECALL ” icon will turn OFF. 28 29 30-31 Recall indicator turns off DATA Mode when watch returns to Press [MODE] until you enter DATA mode. The regular Chronograph mode. mode message “DATA” will be shown for one to two seconds before the number of f
Résumé du contenu de la page N° 9
32-33 The header consisting of the date/time stamp will As you continue to press [RECALL] during the dis- be shown. The number of laps in the segment will play of the last lap, you can advance to the next appear in the upper left while the segment num- segment by pressing [START • SPLIT]. The front ber is displayed in the middle left. If the segment page of the segment will be shown. Say the next shown is not your desired segment, press [START segment is SEG 1. • SPLIT] to reach the desired
Résumé du contenu de la page N° 10
36-37 Note: You cannot delete all segments while the Timer Mode stopwatch is running. If nothing happens when Press [MODE] until you enter the Timer mode. you push and hold [STOP • RESET] check to 3 count-down operation modes are available on make sure the stopwatch is stopped. this stopwatch: • Count down repeat (CR) • Count down stop (CS) • Count down, then count up (CU) The timer is set at the factory to the count-down repeat (CR) mode. At entering timer mode, the mode message “TIME
Résumé du contenu de la page N° 11
40-41 How to set the timer Press [STOP • RESET] (S2) to move to minute digits. Press and hold [RECALL] (S1) for 2 seconds to activate timer setting. Timer setting starts with Press [STOP • RESET] (S2) second digits, which are shown blinking. You can further to go to hour digits. press [START • SPLIT] (S3) to advance the fl ashing Hour digits can be adjusted digits. Or you can press [STOP • RESET] (S2) to from 0 to 19. select other digits. The setting follows the sequence: second, minute
Résumé du contenu de la page N° 12
44-45 Stroke/Stride Measurement STROkE 180.0 Press [MODE] until you enter the Stroke Measure- ment mode. The display will be as follows. At the end of the fi rst second, the display will become steady. STROkE 0.0 If measurement is stopped in the fi rst second (stroke frequency > 180), error signal “ Err “ will In the Stroke or Strides Measurement mode, be shown. After the fi rst second has elapsed, the duration of 3 strokes is taken and the stroke the instantaneous measurement r
Résumé du contenu de la page N° 13
48-49 Press [START • SPLIT] (S3) to toggle between Speed Mode Running KM and MILE. To select the following digits, Press [START • SPLIT] to start the Speed timer. press [STOP • RESET] (S2). The far right digit will The “STOP” indicator is OFF. The maximum time blink and you can set the distance from the least can be up to 19 hr. 59 min. 59.99 sec. signifi cant digit to the most signifi cant digit. The distance can be set in the range 0.000 to 1999.999 km (or ML) using [START • SPLIT] (S3).
Résumé du contenu de la page N° 14
52-53 Before starting again, you can reset the timer by both the speed and elapsed time can be retrieved. pressing [STOP • RESET]. Lap Time & Speed Recall Similar to the Chrono Recall mode, during speed Speed Mode measurement or Stop state, you can press after reset. [RECALL] to recall the speed/lap memories. The Mode message will be shown for one to two seconds as the Mode message display is displayed. Note: When you reset the Speed timer, the speed measurement starts again from a reset s
