Résumé du contenu de la page N° 1
2650 PSI Pressure Washer
Operator’s Manual / Manual del Operario
WARNING ADVERTENCIA
Before using this product, read this manual and follow all Antes de utilizar el producto, lea este manual y siga todas las
Safety Rules and Operating Instructions. Reglas de Seguridad e Instrucciones de Uso.
Snapper™ is a licensed trademark of Briggs & Stratton Power Products.
Snapper™ se usa abajo licencia a Briggs & Stratton Power Products.
Questions? Help is just a moment away!
Preguntas? La ayuda es justa
Résumé du contenu de la page N° 2
2650 PSI Pressure Washer SAVE THESE INSTRUCTIONS TABLE OF CONTENTS SAFETY RULES Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 This is the safety alert symbol. It is used to Know Your Pressure Washer. . . . . . . . . . . . . . . . . . . . . . . . 6 alert you to potential personal injury hazards. Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9 Obey all safety messages that follow this Operation . . . . . . . . . . .
Résumé du contenu de la page N° 3
2650 PSI Pressure Washer WARNING WARNING Running engine gives off carbon monoxide, an Fuel and its vapors are extremely flammable and odorless, colorless, poison gas. explosive. Breathing carbon monoxide can cause nausea, Fire or explosion can cause severe burns or fainting or death. death. Some chemicals or detergents may be harmful if WHEN ADDING FUEL inhaled or ingested, causing severe nausea, Turn pressure washer OFF and let it cool at least 2 minutes fainting or poisoning. before removing
Résumé du contenu de la page N° 4
2650 PSI Pressure Washer WARNING WARNING Rapid retraction of starter cord (kickback) will The high pressure stream of water that this pull hand and arm toward engine faster than equipment produces can pierce skin and its you can let go. underlying tissues, leading to serious injury and possible amputation. Broken bones, fractures, bruises or sprains could result. Spray gun traps high water pressure, even when engine is stopped and water is disconnected, ALWAYS point gun in safe direction and s
Résumé du contenu de la page N° 5
2650 PSI Pressure Washer CAUTION CAUTION Improper treatment of pressure washer can damage it Excessively high or low operating speeds increase risk and shorten its life. of injury and damage to pressure washer. If you have questions about intended use, ask dealer or DO NOT tamper with governed speed. contact Briggs & Stratton Power Products. DO NOT operate pressure washer above rated pressure. NEVER operate units with broken or missing parts, or without protective housing or covers. CAUT
Résumé du contenu de la page N° 6
2650 PSI Pressure Washer KNOW YOUR PRESSURE WASHER Read this operator’s manual and safety rules before operating your pressure washer. Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. Spray Gun Spray Tips High Pressure Hose Nozzle Extension with Quick Connect Recoil Starter Fuel Tank Oil Fill Cap/Dipstick Choke Knob High Pressure Outlet Throttle Lever & Water Inlet Air Filter
Résumé du contenu de la page N° 7
2650 PSI Pressure Washer ASSEMBLY PREPARING PRESSURE IMPORTANT: Read entire operator’s manual before you WASHER FOR USE attempt to assemble or operate your new pressure washer. If you have any problems with the assembly of your pressure washer or if parts are missing or damaged, call the Remove Pressure Washer From pressure washer helpline at 1-800-317-7833. Carton To prepare your pressure washer for operation, you 1. Remove parts bag packed with pressure washer. will need to perform these tasks
Résumé du contenu de la page N° 8
2650 PSI Pressure Washer 3. Insert one “L” hook through hole just above billboard Connect Hose and Water Supply to on left side of handle (viewing from front of unit). Hold Pump hook in place and attach a plastic knob from inside of IMPORTANT: To avoid pump damage, you must assemble unit (Figure 3).Tighten by hand. the nozzle extension to the spray gun and attach all hoses Figure 3 — Attach “L” Hooks to Handle before you start the engine. 1. Uncoil high pressure hose and attach one end of hose S
Résumé du contenu de la page N° 9
2650 PSI Pressure Washer 3. Before connecting garden hose to water inlet, inspect 6. Turn ON water, point gun in a safe direction and inlet screen (Figure 6). Clean screen if it contains debris squeeze trigger to purge pump system of air and or replace if damaged. Refer to “O-Ring Maintenance” impurities. section if inlet screen is damaged. DO NOT run WARNING pressure washer if inlet screen is damaged. Figure 6 — Connect Garden Hose to Water Inlet High pressure spray can cause paint chips or Ins
Résumé du contenu de la page N° 10
2650 PSI Pressure Washer How to Start Pressure Washer HOW TO USE YOUR To start your pressure washer for the first time, follow PRESSURE WASHER these instructions step-by-step.This starting information If you have any problems operating your pressure washer, also applies if you have let the pressure washer sit idle for please call the pressure washer helpline at 1-800-317-7833. at least a day. 1. Place pressure washer near an outside water source Pressure Washer Location capable of supplying wate
Résumé du contenu de la page N° 11
2650 PSI Pressure Washer 9. Engage trigger lock to spray gun trigger (Figure 10). NOTE: Always keep the throttle lever in the “Fast” position when operating the pressure washer. Figure 10 — Spray Gun with Trigger Lock Engaged WARNING Running engines produce heat.Temperature of Trigger Lock muffler and nearby areas can reach or exceed 150°F (65°C). Severe burns can occur on contact. 10. When starting engine, position yourself as recommended Exhaust heat/gases can ignite combustibles, in Figure 11
Résumé du contenu de la page N° 12
2650 PSI Pressure Washer 4. Pull back on collar, insert new spray tip and release How to Use Spray Tips collar.Tug on spray tip to make sure it is securely in The quick–connect on the nozzle extension allows you to place. switch between four different spray tips.The spray tips vary the spray pattern as shown (Figure 12). 5. For most effective cleaning, keep spray tip from 8 to 24 inches away from cleaning surface. If you get spray Follow these instructions to change spray tips: tip too close, yo
Résumé du contenu de la page N° 13
2650 PSI Pressure Washer 7. Allow detergent to soak in between 3–5 minutes 5. Apply a high pressure spray to a small area and then before washing and rinsing. Reapply as needed to check the surface for damage. If no damage is found, prevent surface from drying. Do Not allow detergent you can assume it is okay to continue rinsing. to dry on (prevents streaking). 6. Start at top of area to be rinsed, working down with IMPORTANT: You must flush the chemical injection same overlapping strokes as you
Résumé du contenu de la page N° 14
2650 PSI Pressure Washer SPECIFICATIONS PRESSURE WASHER Outlet Pressure . . . . . . . . . . . . . . . . . . . . . . . . . 2650 psi MAINTENANCE Flow Rate . . . . . . . . . . . . . . 2.5 gallons per minute (gpm) Detergent Use detergent approved for pressure washers Check and Clean Inlet Screen Water Supply Temperature . . . . Not to Exceed 100°F Examine the screen on the water inlet. Clean it if the Automatic Cool . . . . . . . . . . . . . Will cycle when water screen is clogged or replace it if
Résumé du contenu de la page N° 15
2650 PSI Pressure Washer 1. Detach spray gun and nozzle extension from high 6. Reinstall spray tip and in-line filter into nozzle pressure hose. Detach nozzle extension from spray extension. gun and remove o-ring and screen from nozzle 7. Reconnect nozzle extension to spray gun. extension. Flush screen, spray gun, and nozzle 8. Reconnect water supply, turn on water, and start extension with clean water to clear debris. engine. 2. Place in-line filter screen into threaded end of nozzle 9. Test pr
Résumé du contenu de la page N° 16
2650 PSI Pressure Washer PREPARING THE UNIT CAUTION You must protect your unit from freezing temperatures. FOR STORAGE Failure to do so will permanently damage your pump and Water should not remain in the unit for long periods of render your unit inoperable. time. Sediments or minerals can deposit on pump parts and Freeze damage is not covered under warranty. “freeze” pump action. If you do not plan to use the pressure washer for more than 30 days, follow this procedure: CAUTION 1. Flush det
Résumé du contenu de la page N° 17
2650 PSI Pressure Washer NOTES 17
Résumé du contenu de la page N° 18
2650 PSI Pressure Washer TROUBLESHOOTING Problem Cause Correction 1. Low pressure spray tip installed. 1. Replace spray tip with high pressure spray tip. 2. Water inlet is blocked. 2. Clear inlet. 3. Inadequate water supply. 3. Provide adequate water flow. 4. Inlet hose is kinked or leaking. 4. Straighten inlet hose, patch leak. Pump has following problems: 5. Clogged inlet hose strainer. 5. Check and clean inlet hose failure to produce pressure, erratic strainer. pressure, chattering, loss of 6
Résumé du contenu de la page N° 19
SNAPPER™ OWNER WARRANTY POLICY Effective August 1, 2004 LIMITED WARRANTY “Snapper™ is a licensed trademark of Briggs & Stratton Power Products. Briggs & Stratton Power Products will repair or replace, free of charge, any part, or parts of the equipment** that are defective in material or workmanship or both.Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser.This warranty is effective for the time periods and subject to the conditi
Résumé du contenu de la page N° 20
Lavadora de Presión 2650 PSI CONSERVE ESTAS INSTRUCCIONES TABLA DE CONTENIDOS REGLAS DE SEGURIDAD Reglas De Seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-23 Éste es el símbolo de alerta de seguridad. Sirve Conozca Su Lavadora de Presión . . . . . . . . . . . . . . . . . . . . . . . . 24 para advertir al usuario de un posible riesgo para Montaje . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-27 su integridad física. Siga todos
