Instruction d'utilisation Harbor Freight Tools 47869

Résumé du contenu de la page N° 1

®
AIR MICRO
DIE GRINDER
Model 47869
ASSEMBLY and OPERATING
INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright 2002 by Harbor Freight Tools . All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353

Résumé du contenu de la page N° 2

Specifications Collet Size 1/8” Air Inlet 1/4”-18 NPT Maximum Air Pressure 90 PSI Maximum Rpm’s 56,000 Air Consumption 2 CFM @ 90 PSI Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. Safety Warn

Résumé du contenu de la page N° 3

8. Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. 9. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines or air hoses. 10. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lub

Résumé du contenu de la page N° 4

Note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool perfor- mance. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be under- stood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Addit

Résumé du contenu de la page N° 5

Operation Operational Warnings!! 1. Never install a carbide tipped or steel circular saw blade for use on this Die Grinder. 2. Never install a wood carving blade, carving disc with chain saw cutters, or a cutting carving disc on this Die Grinder. 3. All accessories must be rated for at least 56,000 rpm’s. Wheels and other accessories running over rated speed can fly apart and cause injury. 1/4”-18 NPT Die Grinder For best service you should incorporate an oiler, regulator, and inline filter,

Résumé du contenu de la page N° 6

Operation (continued) Usage. Note: Always disconnect the Die Grinder from the air compressor hose before changing or adjusting accessories. 1. Use the two Wrenches (#30) to attach accessories. Place the Wrench (#30) on the notch of the Clamping Nut (#25) to secure it. Use the other Wrench (#30) to turn the Collet (#24). 2. Insert the desired 1/8” mandrel into the Collet (#24) at least 5/8”. 3. Using the Wrenches (#30), tighten the Clamping Nut (#25). Note: Before each use check the Collet

Résumé du contenu de la page N° 7

Parts List Part No. Description Qty. Part No. Description Qty. 1 End Holder 1 16 Spacer 1 2 Screw 1 17 Lateral Disc 1 3 0-ring 2 18 Ball Bearing 2 4 Sliding Knob 1 19 Inner Bearing/Bushing 1 5 0-ring 1 20 Outer Bearing/Bushing 1 6 Hose Plug 1 21 Collet Foundation 1 7 Pin 1 22 Sleeve 1 8 Plug 1 23 Front Cover 1 9 Intake Plate 1 24 Collet 1 10 Ball Bearing 1 25 Clamping Nut 1 11 Bearing Plate 1 26 Muffler Tube 1 12 P

Résumé du contenu de la page N° 8

Assembly Drawing 29 28 27 27 1 2 3 26 6 4 7 14 5 3 15 8 16 9 17 10 18 11 12 19 22 20 13 18 23 24 30 21 25 Note: The second Wrench (#30), the tool oil, and the entire length of the Air Hose (#28) are not shown. Page 8 SKU 47869