Résumé du contenu de la page N° 1
10” Bench Grinder
6510
Set up and OperatinG inStructiOnS
®
distributed exclusively by harbor Freight t ools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
SaVe thiS manual.
© ®
Copyright 1997 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the
Résumé du contenu de la page N° 2
unpackinG .................................. 9 cOntentS aSSemBl Y .................................. 10 impOrtant SaFetY tOOl reSt aSSemBl Y .................10 inFOrmatiOn ............................ 3 eYe Shield aSSemBl Y ................10 General tOOl SaFetY WarninGS ......................................3 GrindinG Wheel aSSemBl Y ...... 11 GrOundinG inStructiOnS ..... 5 OperatiOn ................................ 13 110-120 V~ GrOunded tOOlS: OperatiOn nOteS ........................13 tO
Résumé du contenu de la page N° 3
nOtice is used to SaVe thiS manual address practices Keep this manual for the safety warn- not related to personal injury. ings and precautions, assembly, operat- cautiOn, without ing, inspection, maintenance and cleaning the safety alert procedures. Write the product’s serial symbol, is used to address number in the back of the manual near the practices not related to assembly diagram (or month and year of personal injury. purchase if product has no number). Keep this manual and
Résumé du contenu de la page N° 4
7. DON’T FORCE TOOL. It will do the glasses only have impact resistant job better and safer at the rate for lenses, they are NOT safety glasses. which it was designed. 12. SECURE WORK. Use clamps or a 8. USE RIGHT TOOL. Don’t force tool vise to hold work when practical. It’s or attachment to do a job for which it safer than using your hand and it was not designed. frees both hands to operate tool. recOmmended minimum Wire 13. DON’T OVERREACH. Keep proper GauGe FOr eXtenSiOn cOrdS footing
Résumé du contenu de la page N° 5
or other part that is damaged should equipment-grounding conductor to a be properly repaired or replaced. live terminal. 20. DIRECTION OF FEED. Feed work 4. Check with a qualified electrician or into a blade or cutter against the di- service personnel if the grounding rection of rotation of the wheel only. instructions are not completely under- stood, or if in doubt as to whether the tool is properly grounded. GrOundinG inStructiOnS 5. Use only 3-wire extension cords that tO preVent have
Résumé du contenu de la page N° 6
7. Adjust distance between wheel and 110-120 V~ double insulated work rest to maintain 0.125 inch or t ools: t ools with t wo prong less separation as the diameter of the plugs wheel decreases with use. 8. Frequently clean grinding dust from beneath grinder. 9. Wear a full face shield over ANSI- approved safety goggles during use. 10. Do not grind with side of wheel un- less wheel is specifically designed for that type of grinding. Outlets for 2-prong plug 11. dO nOt Operate With anY 1.
Résumé du contenu de la page N° 7
17. Avoid unintentional starting. Prepare 21. The warnings, precautions, and in- to begin work before turning on the structions discussed in this instruction tool. manual cannot cover all possible con- ditions and situations that may occur. 18. People with pacemakers should It must be understood by the operator consult their physician(s) before use. that common sense and caution are Electromagnetic fields in close prox- factors which cannot be built into this imity to heart pacemaker c
Résumé du contenu de la page N° 8
4. Use tools with the lowest vibration when there is a choice between dif- ferent processes. 5. Include vibration-free periods each day of work. 6. Grip tool as lightly as possible (while still keeping safe control of it). Let the tool do the work. 7. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately. SaVe theSe inStructiOnS. Page 8 For technical questions, please call 1-800-444-3353. SKU 6510
Résumé du contenu de la page N° 9
SpeciFicatiOnS 120 V~ / 60 Hz / 8.4 A Electrical Input 1 HP (rated) / 2 HP (peak) No Load Speed 1750 RPM Accessory Dia. 10” Max. Arbor Size 20mm unpackinG When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at 1-800-444-3353 as soon as possible. ref description Quantity 1 Bench Grinder Unit 1 3 Eye Shield 2 4 Shield Supports 2 reV 09e SKU 6510 For technical questions, please call 1-800-444-3353. Page 9
Résumé du contenu de la page N° 10
aSSemBl Y The 10” Bench Grinder requires minor assembly. The assembly instructions below are written for the left side but the right side is identical. Refer to the Parts List, at the back of this manual, for the individual part t ool numbers. rest (7) t ool rest t ool rest assembly nob (8) k 1. Bolt the BENCH GRINDER UNIT (1) FiGure 2 – moving t ool rest to a stable workplace. 3. Pivot the tool rest down and forward so that it is in a horizontal position and replace the front TOOL
Résumé du contenu de la page N° 11
Washers GrindinG Wheel aSSemBl Y (14) Bolt Shield (12) remove Grinding Wheel Supports (4) eye Shield (3) eye nut Wheel Shield (13) cover (6) nut (13) (3) Grinding Wheel (2) Washers (14) Bolt FiGure 4 – (12) attaching the eye Shield Spindle to Wheel cover (9) 2. Remove the BOLT (12) and NUT (13) from the upper grinder housing as Wheel Wheel shown in Figure 4. mounting mounting Washer (11) nut (10) 3. Align the EYE SHIELD Assembly FiGure 5 – assembling the Grinder with holes
Résumé du contenu de la page N° 12
installing Grinding Wheel 2. With the Bench Grinder running, grip the handle of the dresser firmly with note: Do not use aluminum oxide grind- one hand and the arm of the dresser ing wheels when grinding nonferrous with the other. metals such as aluminum and brass. Use silicon carbide grinding wheels 3. Using the TOOL REST (7) as sup- for all nonferrous metals port, apply the dresser evenly to all surfaces of the GRINDING WHEEL. 1. Make sure the inside WHEEL MOUNTING WASHER (11) is on th
Résumé du contenu de la page N° 13
General Operation OperatiOn 1. Obtain a tray that is large enough caution: The grinding wheels must al- for the workpiece to fit into, fill it with ways be checked for cracks of imper- water and place it near the Bench fections. This is done with the “ring Grinder. test”. Tap the wheel gently near the outer rim with the handle of a screw- 2. Turn the Bench Grinder on. driver; you should hear a clear bell- like ringing. if a dull thud occurs do 3. Once the GRINDING WHEEL has not use the
Résumé du contenu de la page N° 14
pleaSe read the FOllOWinG careFull Y THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/ OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACE
Résumé du contenu de la page N° 15
aSSemBl Y diaGram reV 99h SKU 6510 For technical questions, please call 1-800-444-3353. Page 15 1 2 3 4 5 4 6 19 7 9 19 42 46 8 18 17 19 11 7 21 45 7 10 11 12 13 14 15 16 15 22 19 7 23 39 24 20 26 25 27 34 35 31 38 11 10 19 11 18 4 28 4 29 30 1 36 11 1 37 40 19 32 43 44 19 9 46
Résumé du contenu de la page N° 16
limited 1 Year / 90 da Y WarrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship. Har- bor Freight Tools also warrants to the original purchaser, for a period of one year from date of purchase, that al
