Résumé du contenu de la page N° 1
BRAKE CALIPER WIND BACK
TOOL SET
Model 97456
SET uP AND OPERATINg INSTRuCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MAN
Résumé du contenu de la page N° 2
NOTICE is used to SAVE THIS MANuAL Notice address practices Keep this manual for the safety warn- not related to personal injury. ings and precautions, assembly, operat- CAuTION, without ing, inspection, maintenance and cleaning CAuTION the safety alert procedures. Write the product’s serial symbol, is used to address number in the back of the manual near the practices not related to assembly diagram (or month and year of personal injury. purchase if product has no number). Keep t
Résumé du contenu de la page N° 3
tion while operating pneumatic tools be controlled with the Trigger is may result in serious personal injury. dangerous and must be repaired. b. Use safety equipment. Always c. Disconnect the air hose from the wear ANSI-approved safety impact pneumatic tool and release any goggles and NIOSH-approved dust remaining air pressure before mask/respirator. Safety equipment making any adjustments, changing such as non-skid safety shoes, hard accessories, or storing pneumatic hat, or hearing pro
Résumé du contenu de la page N° 4
abnormal vibration occurs, stop use Vibration Hazard immediately. This tool vibrates during use. Repeated or long-term exposure to Specific Safety Rules vibration may cause temporary or permanent physical injury, particularly 1. Maintain labels and nameplates to the hands, arms and shoulders. To on the Caliper Wind Brake Tool reduce the risk of vibration-related Set. These carry important safety injury: information. If unreadable or missing, contact Harbor Freight Tools for a 1. Any
Résumé du contenu de la page N° 5
TO PREVENT SPECIFICATIONS WARNINg SERIOuS INjuRY Product Universal fit. Works with most European, FROM ACCIDENTAL Application Asian, and United States made vehicles. OPERATION: Operating Air 72 PSI to 110 PSI Pressure Disconnect the Caliper Wind Brake Tool from its Air Inlet Size 1/4” - 18 NPT compressed air supply Forged steel Disc Adapters. Fabrication Die Cast Aluminum Gun with stamped source, and release any steel and machined steel. compressed air from the tool Rotates left or
Résumé du contenu de la page N° 6
® 518i, 525i, 1x, 740i, 850ci, Sri (R), Toyota Celica, Co- ® M5 (F), Mercedes Benz 190, rolla, GT, MR2 (R), VW Golf Gti, Jetta, Synchro, 200, 300, 420, 560 (F), ® ® Jetta Gti, Passat CL, GL, Mitsubishi Colt (F), Nissan GT, Corrado, Scirroca, GTX. Mlera, Stanza, Sunny (F), ® ® Range Rover Austin, Metro, Pad 8: General Motors most 1-7/8” 200
Résumé du contenu de la page N° 7
general Operating Instructions DIRECTION HANDLE (18A) 1. Place the proper Pad on the Sliding Bar (2A) of the tool. (See Figure C.) FIguRE C PAD TRIggER (6A) FIguRE E SLIDINg BAR (2A) 5. When finished, release pressure on the Trigger (6A). Then pull out on the Sliding Bar (2A) to remove the Pad 2. Connect an air hose to the Air from the caliper. (See Figure F.) Connector (5A) of the tool. Turn 6. Turn off the air compressor. on the air compressor, and set its Disconnect the air hose
Résumé du contenu de la page N° 8
WARNINg TO PREVENT SERIOuS INjuRY FROM ACCIDENTAL OPERATION: Disconnect the tool from its compressed air supply source before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOuS INjuRY FROM TOOL FAILuRE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. BEFORE EACH uSE, inspect the general condition of the tool.
Résumé du contenu de la page N° 9
PARTS LIST & ASSEMBLY DIAgRAM REV 08c SKU 97456 For technical questions, please call 1-800-444-3353. Page 9 22A 23A 25A 9A 15A 2A 1A 7A 8A 13A 6A 14A 31A 5A 20A 28A 29A 24A 21A 11A 17A 12A Part # Description 1A Body 2A Sliding Bar 3A O-Ring 4A Bottom Cap 5A Air Connector 6A Trigger 7A Hollow Pin 8A Spring 9A O-Ring 10A Air Control Pin 11A O-Ring 12A Base Nut 13A O-Ring 14A Adapter 15A Steel Ball 16A Spring 17A Hex Set Screw 18A Direction Handle 19A Rivet 20A Piston O-Ring 21A Piston 3A 22A Bolt
Résumé du contenu de la page N° 10
LIMITED 1 YEAR WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase (90 days if used by a professional contractor or if used as rental equipment). This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repair
