Résumé du contenu de la page N° 1
OWNER’S MANUAL
The Basics
of Metal Detecting
Your Fast Tracker Metal Detector is a MOTION metal detector; movement over
an object is required in order for the machine to detect an object and emit a tone.
The Fast Tracker has eliminated the two most difficult aspects of detecting -
ground balancing and target tuning. Both of these functions are automatic. With
only two operating knobs, you are on the Fast Track to finding buried treasure!
CAUTION:
FOR OUTDOOR USE ONLY:
• If demonstrating ind
Résumé du contenu de la page N° 2
FAST TRACKER FEATURES Fast Tracker FEATURES Padded Armrest Discriminate Control S-Rod Handle System Detector Stand Comfort Hand-grip Headphone Jack Sensitivity Control Interchangeable Coil System 7" Waterproof Coil 2
Résumé du contenu de la page N° 3
EASY ASSEMBLY Search Coil Assembling your Fast Tracker Metal Detector is easy and requires no tools. Just follow these steps: 1 Using the supplied bolt and knurled knob, attach the search coil to the lower stem. Bottom side 2 Press the button on the upper end of the lower stem and slide the Lower Search Stem lower stem into the upper stem. Coil Cable Adjust the stem to a length Upper Stem that lets you maintain a com- Lower fortable upright posture, with Stem your arm relaxed at your side.
Résumé du contenu de la page N° 4
BATTERIES Use ALKALINE batteries only. Follow these steps to install the batteries. 1 Carefully remove the battery compartment door by pressing the release clip on the right side of the door. 2 Snap one battery on to each of the terminals and place the batteries inside the compartment. The battery compartment is a tight fit. Insert one battery with the terminals facing down, and the second battery with the terminals facing outward. See illustration. 3 Replace the compartment door by f
Résumé du contenu de la page N° 5
FAST DEMONSTRATION Here is a quick way to demonstrate the basic features of your FAST TRACKER. Supplies Needed a. A small nail d. A nickel b. A small piece of foil e. A dime c. A quarter f. A penny Position your Fast Tracker Keep the detector away from metal objects. Have a friend hold the detector while you pass the objects over the search coil. Or, hang the detector over the edge of a chair or table, away from walls, floors and other metal objects. Remove your jewelry and watch (they also cont
Résumé du contenu de la page N° 6
OPERATION The Fast Tracker is a MOTION metal detector; the search coil must be in motion over the targeted object in order for the machine to detect the object and emit a tone. Motion is required in order for the detector to automatically GROUND BALANCE. All soil and sand is different, containing varying amounts of naturally occurring minerals. As you sweep the search coil over the ground, your metal detector is constantly READING and AVERAGING the ground’s mineralization, in order to differe
Résumé du contenu de la page N° 7
OPERATION Select the MODE OF OPERATION The Fast Tracker has two operating modes, ALL METAL and DISCRIMINATION. ALL METAL To enter the ALL METAL mode, click the right knob (Discriminate) off, 100% counterclockwise. In the full counterclockwise position, you will detect all types of metal. In the ALL METAL mode, your detector will emit only one tone, regardless of the type of metal detected. It will detect low-grade metals like iron (a nail) or aluminum (foil). It will also detect more valuable i
Résumé du contenu de la page N° 8
IN THE FIELD TECHNIQUES SWEEP TECHNIQUE Sweep the search coil in a slow, consistent, side-to-side motion. The detector’s circuitry is constantly calculating the ground’s mineralization. A steady, consistent coil speed is required for the detector to make an accurate calculation. Keep the search coil about one inch above the ground. Keep the coil even with the ground. Do not raise the coil at the ends of your sweep. WRONG CORRECT TONE RESPONSE Only dig up targets that induce repeatable tones.
Résumé du contenu de la page N° 9
IN THE FIELD TECHNIQUES PINPOINTING Accurate pinpointing takes practice and is best accomplished by “X-ing” the sus- pected target area. 1 Once a buried target is identified by a good tone response, continue sweeping the coil over the target in a narrowing side-to-side pattern. 2 Take visual note of the place on the ground where the “beep” occurs as you move the coil slowly from side to side. 3 Stop the coil directly over this spot on the ground. 4 Now move the coil straight forward and
Résumé du contenu de la page N° 10
CARE AND MAINTENANCE Your Fast Tracker Metal Detector is an example of superior design and craftsmanship. The following suggestions will help you care for your metal detector so that you can enjoy it for years. Handle the metal detector gently and carefully. Dropping it can damage electronic components. Use and store the metal detector only in normal temperature environments. Temperature extremes can shorten the life of electronic devices and distort or melt plastic parts. Wipe the metal detect
Résumé du contenu de la page N° 11
METAL DETECTING APPLICATIONS COIN SHOOTING Searching for coins is the most popular metal detecting application. We receive testimonials every day from BOUNTY HUNTER users finding very old coins — many times from the 1800’s or earlier — in old school yards, parks, and even their own back yards. To adjust your detector for coin shooting, you want to click on the ALL METAL control knob to about the 1:00 position. Find an older pull tab, and adjust the discrimination control to the point where yo
Résumé du contenu de la page N° 12
TREASURE HUNTER’S CODE OF ETHICS: 1. Respect the rights and property of others. 2. Observe all laws, whether national, state or local. 3. Never destroy historical or archaeological treasures. 4. Leave the land and vegetation as it was. Fill in the holes. 5. All treasure hunters may be judged by the example you set. Always obtain permission before searching any site. Be extremely careful while probing, picking up, or discarding trash items. And ALWAYS COVER YOUR HOLES! FIRST TEXAS PRODUCTS, LP 5-
